Magtek DynaFlex User manual

MagTek I 1710 Apollo Court I Seal Beach, CA 90740 I Phone: [phone] I Technical Support: [phone]
www.magtek.com
DynaFlex, DynaProx
Utility BCR
Manual ( Windows )
June 15 2022
Document Number:
D100005916-10
REGISTERED TO ISO 9001:2015

DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 2 of 16 (D100005916-10)
Copyright © 2006 - 2022 MagTek, Inc.
Printed in the United States of America
INFORMATION IN THIS PUBLICATION IS SUBJECT TO CHANGE WITHOUT NOTICE AND
MAY CONTAIN TECHNICAL INACCURACIES OR GRAPHICAL DISCREPANCIES. CHANGES
OR IMPROVEMENTS MADE TO THIS PRODUCT WILL BE UPDATED IN THE NEXT
PUBLICATION RELEASE. NO PART OF THIS DOCUMENT MAY BE REPRODUCED OR
TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRONIC OR MECHANICAL, FOR
ANY PURPOSE, WITHOUT THE EXPRESS WRITTEN PERMISSION OF MAGTEK, INC. SOME
FEATURES AND FUNCTIONS MAY BE DOCUMENTED, BUT NOT AVAILABLE WITH THE
CURRENT RELEASE OF THE PRODUCT. PLEASE CONTACT YOUR MAGTEK
REPRESENTATIVE FOR QUESTIONS ABOUT SPECIFIC FEATURES AND FUNCTIONS AND
WHEN THEY ARE SCHEDULED TO BECOME AVAILABLE.
MagTek®, MagnePrint®, and MagneSafe® are registered trademarks of MagTek, Inc.
Magensa™ is a trademark of MagTek, Inc.
DynaFlex, and DynaProxare trademarks of MagTek, Inc.
AAMVA™ is a trademark of AAMVA.
American Express® and EXPRESSPAY FROM AMERICAN EXPRESS® are registered trademarks of
American Express Marketing & Development Corp.
D-PAYMENT APPLICATION SPECIFICATION® is a registered trademark to Discover Financial
Services CORPORATION
MasterCard® is a registered trademark and PayPass™and Tap & Go™are trademarks of MasterCard
International Incorporated.
Visa® and Visa payWave® are registered trademarks of Visa International Service Association.
ANSI®, the ANSI logo, and numerous other identifiers containing "ANSI" are registered trademarks,
service marks, and accreditation marks of the American National Standards Institute (ANSI).
ISO® is a registered trademark of the International Organization for Standardization.
UL™and the UL logo are trademarks of UL LLC.
PCI Security Standards Council® is a registered trademark of the PCI Security Standards Council, LLC.
EMV® is a registered trademark in the U.S. and other countries and an unregistered trademark elsewhere.
The EMV trademark is owned by EMVCo, LLC. The Contactless Indicator mark, consisting of four
graduating arcs, is a trademark owned by and used with permission of EMVCo, LLC.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by MagTek is under license.
Google Play™ store, Google Wallet™ payment service, and Android™ platform are trademarks of
Google Inc.
Apple Pay®, iPhone®, iPod®, Mac®, and OS X® are registered trademarks of Apple Inc., registered in
the U.S. and other countries. iPad™ is a trademark of Apple. Inc. App StoreSM is a service mark of
Apple Inc., registered in the U.S. and other countries. IOS is a trademark or registered trademark of
Cisco in the U.S. and other countries and is used by Apple Inc. under license.
Microsoft®, Windows®, and .NET® are registered trademarks of Microsoft Corporation.
All other system names and product names are the property of their respective owners.

DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 3 of 16 (D100005916-10)
Table 0-1 - Revisions
Rev Number
Date
Notes
10
June 15, 2022
Initial Release

DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 4 of 16 (D100005916-10)
LIMITED WARRANTY
MagTek warrants that the products sold pursuant to this Agreement will perform in accordance with
MagTek’s published specifications. This warranty shall be provided only for a period of one year from
the date of the shipment of the product from MagTek (the “Warranty Period”). This warranty shall apply
only to the “Buyer” (the original purchaser, unless that entity resells the product as authorized by
MagTek, in which event this warranty shall apply only to the first repurchaser).
During the Warranty Period, should this product fail to conform to MagTek’s specifications, MagTek
will, at its option, repair or replace this product at no additional charge except as set forth below. Repair
parts and replacement products will be furnished on an exchange basis and will be either reconditioned or
new. All replaced parts and products become the property of MagTek. This limited warranty does not
include service to repair damage to the product resulting from accident, disaster, unreasonable use,
misuse, abuse, negligence, or modification of the product not authorized by MagTek. MagTek reserves
the right to examine the alleged defective goods to determine whether the warranty is applicable.
Without limiting the generality of the foregoing, MagTek specifically disclaims any liability or warranty
for goods resold in other than MagTek’s original packages, and for goods modified, altered, or treated
without authorization by MagTek.
Service may be obtained by delivering the product during the warranty period to MagTek (1710 Apollo
Court, Seal Beach, CA 90740). If this product is delivered by mail or by an equivalent shipping carrier,
the customer agrees to insure the product or assume the risk of loss or damage in transit, to prepay
shipping charges to the warranty service location, and to use the original shipping container or equivalent.
MagTek will return the product, prepaid, via a three (3) day shipping service. A Return Material
Authorization (“RMA”) number must accompany all returns. Buyers may obtain an RMA number by
contacting MagTek Support Services at [phone].
EACH BUYER UNDERSTANDS THAT THIS MAGTEK PRODUCT IS
OFFERED AS-IS. MAGTEK MAKES NO OTHER WARRANTY, EXPRESS OR
IMPLIED, AND MAGTEK DISCLAIMS ANY WARRANTY OF ANY OTHER
KIND, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
IF THIS PRODUCT DOES NOT CONFORM TO MAGTEK’S
SPECIFICATIONS, THE SOLE REMEDY SHALL BE REPAIR OR
REPLACEMENT AS PROVIDED ABOVE. MAGTEK’S LIABILITY, IF ANY,
SHALL IN NO EVENT EXCEED THE TOTAL AMOUNT PAID TO MAGTEK
UNDER THIS AGREEMENT. IN NO EVENT WILL MAGTEK BE LIABLE TO
THE BUYER FOR ANY DAMAGES, INCLUDING ANY LOST PROFITS, LOST
SAVINGS, OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OF, OR INABILITY TO USE, SUCH PRODUCT,
EVEN IF MAGTEK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY.

DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 5 of 16 (D100005916-10)
LIMITATION ON LIABILITY
EXCEPT AS PROVIDED IN THE SECTIONS RELATING TO MAGTEK’S LIMITED WARRANTY,
MAGTEK’S LIABILITY UNDER THIS AGREEMENT IS LIMITED TO THE CONTRACT PRICE OF
THIS PRODUCT.
MAGTEK MAKES NO OTHER WARRANTIES WITH RESPECT TO THE PRODUCT, EXPRESSED
OR IMPLIED, EXCEPT AS MAY BE STATED IN THIS AGREEMENT, AND MAGTEK
DISCLAIMS ANY IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
MAGTEK SHALL NOT BE LIABLE FOR CONTINGENT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES TO PERSONS OR PROPERTY. MAGTEK FURTHER LIMITS ITS LIABILITY OF ANY
KIND WITH RESPECT TO THE PRODUCT, INCLUDING NEGLIGENCE ON ITS PART, TO THE
CONTRACT PRICE FOR THE GOODS.
MAGTEK’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDIES ARE STATED IN THIS
SECTION AND IN THE SECTION RELATING TO MAGTEK’S LIMITED WARRANTY.

DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 6 of 16 (D100005916-10)
SOFTWARE LICENSE AGREEMENT
IMPORTANT: YOU SHOULD CAREFULLY READ ALL THE TERMS, CONDITIONS AND
RESTRICTIONS OF THIS LICENSE AGREEMENT BEFORE INSTALLING THE SOFTWARE
PACKAGE. YOUR INSTALLATION OF THE SOFTWARE PACKAGE PRESUMES YOUR
ACCEPTANCE OF THE TERMS, CONDITIONS, AND RESTRICTIONS CONTAINED IN THIS
AGREEMENT. IF YOU DO NOT AGREE WITH THESE TERMS, CONDITIONS, AND
RESTRICTIONS, PROMPTLY RETURN THE SOFTWARE PACKAGE AND ASSOCIATED
DOCUMENTATION TO THE ADDRESS IN THIS DOCUMENT, ATTENTION: CUSTOMER
SUPPORT.
TERMS, CONDITIONS, AND RESTRICTIONS
MagTek, Incorporated (the "Licensor") owns and has the right to distribute the described software and
documentation, collectively referred to as the "Software."
LICENSE: Licensor grants you (the "Licensee") the right to use the Software in conjunction with
MagTek products. LICENSEE MAY NOT COPY, MODIFY, OR TRANSFER THE SOFTWARE IN
WHOLE OR IN PART EXCEPT AS EXPRESSLY PROVIDED IN THIS AGREEMENT. Licensee
may not decompile, disassemble, or in any other manner attempt to reverse engineer the Software.
Licensee shall not tamper with, bypass, or alter any security features of the software or attempt to do so.
TRANSFER: Licensee may not transfer the Software or license to the Software to another party without
the prior written authorization of the Licensor. If Licensee transfers the Software without authorization,
all rights granted under this Agreement are automatically terminated.
COPYRIGHT: The Software is copyrighted. Licensee may not copy the Software except for archival
purposes or to load for execution purposes. All other copies of the Software are in violation of this
Agreement.
TERM: This Agreement is in effect as long as Licensee continues the use of the Software. The Licensor
also reserves the right to terminate this Agreement if Licensee fails to comply with any of the terms,
conditions, or restrictions contained herein. Should Licensor terminate this Agreement due to Licensee's
failure to comply, Licensee agrees to return the Software to Licensor. Receipt of returned Software by
the Licensor shall mark the termination.
LIMITED WARRANTY: Licensor warrants to the Licensee that the disk(s) or other media on which
the Software is recorded are free from defects in material or workmanship under normal use.
THE SOFTWARE IS PROVIDED AS IS. LICENSOR MAKES NO OTHER WARRANTY OF ANY
KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Because of the diversity of conditions and hardware under which the Software may be used, Licensor
does not warrant that the Software will meet Licensee specifications or that the operation of the Software
will be uninterrupted or free of errors.
IN NO EVENT WILL LICENSOR BE LIABLE FOR ANY DAMAGES, INCLUDING ANY LOST
PROFITS, LOST SAVINGS, OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE, OR INABILITY TO USE THE SOFTWARE. Licensee's sole remedy in

DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 7 of 16 (D100005916-10)
the event of a defect in material or workmanship is expressly limited to replacement of the Software
disk(s) if applicable.
GOVERNING LAW: If any provision of this Agreement is found to be unlawful, void, or
unenforceable, that provision shall be removed from consideration under this Agreement and will not
affect the enforceability of any of the remaining provisions. This Agreement shall be governed by the
laws of the State of California and shall inure to the benefit of MagTek, Incorporated, its successors or
assigns.
ACKNOWLEDGMENT: LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS
AGREEMENT, UNDERSTANDS ALL OF ITS TERMS, CONDITIONS, AND RESTRICTIONS, AND
AGREES TO BE BOUND BY THEM. LICENSEE ALSO AGREES THAT THIS AGREEMENT
SUPERSEDES ANY AND ALL VERBAL AND WRITTEN COMMUNICATIONS BETWEEN
LICENSOR AND LICENSEE OR THEIR ASSIGNS RELATING TO THE SUBJECT MATTER OF
THIS AGREEMENT.
QUESTIONS REGARDING THIS AGREEMENT SHOULD BE ADDRESSED IN WRITING TO
MAGTEK, INCORPORATED, ATTENTION: CUSTOMER SUPPORT, AT THE ADDRESS LISTED
IN THIS DOCUMENT, OR E-MAILED TO SUPPOR[email protected].
DEMO SOFTWARE / SAMPLE CODE: Unless otherwise stated, all demo software and sample code
are to be used by Licensee for demonstration purposes only and MAY NOT BE incorporated into any
production or live environment. The PIN Pad sample implementation is for software PIN Pad test
purposes only and is not PCI compliant. To meet PCI compliance in production or live environments, a
third-party PCI compliant component (hardware or software-based) must be used.

0 - Table of Contents
DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 8 of 16 (D100005916-10)
Table of Contents
Limited Warranty .............................................................................................................................................. 4
SOFTWARE LICENSE AGREEMENT ................................................................................................................. 6
Table of Contents .............................................................................................................................................. 8
1Introduction ............................................................................................................................................... 9
1.1 About This Document ...................................................................................................................... 9
1.2 System Requirements ..................................................................................................................... 9
1.3 How to Download, Install, and Launch the Software.................................................................. 9
2How to Connect to Devices ...................................................................................................................10
2.1 How to Connect Using the USB Connection ............................................................................... 10
2.2 How to Connect Using the Serial Connection ............................................................................12
3How to use the Barcode Reader........................................................................................................... 13
3.1 Barcode Returned Unencrypted...................................................................................................13
3.2 Barcode Returned Encrypted........................................................................................................14
3.3 Settings............................................................................................................................................ 15

1 - Introduction
DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 9 of 16 (D100005916-10)
1Introduction
1.1 About This Document
This document provides instructions to use the DynaFlex, DynaProx Utility BCR software for
demonstrating barcode reading operations. It is part of a larger library of documents designed to assist
implementers. For details, see the product Support pages on www.magtek.com.
1.2 System Requirements
A Windows 10 host with available USB port
Microsoft .NET 4.6.1 and above installed on the host
DynaFlex, DynaFlex Pro, or DynaProx device(s)
USB-C cable with USB Type-A or USB-C, Serial to USB adapter cable
Software 1000008341 DynaFlex, DynaProx Utility BCR, provided by MagTek
1.3 How to Download, Install, and Launch the Software
To download DynaFlex, DynaProx Utility BCR software, follow these steps.
1) Download the software with the name 1000008341.zip (DynaFlex, DynaProx Utility BCR) from
MagTek.
2) Extract the .zip file on the host’s hard drive.
3) If needed, download and install Microsoft .NET 4.6.1 or above from
https://dotnet.microsoft.com/download/dotnet-framework.
4) Launch BCRUtility.
5) See the steps in the sections below to connect to a device.

2 - How to Connect to Devices
DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 10 of 16 (D100005916-10)
2How to Connect to Devices
To connect via an interface listed in the Device list box, follow these steps.
2.1 How to Connect Using the USB Connection
1) For best results, use the cable that is included with the device.
2) Connect the USB-C end of the cable to DynaFlex or DynaProx device.
Figure 2-1 - Connecting DynaFlex / DynaProx to a USB Host
3) If you plan to route the cable out the back of the device, route the cable through the cable
management clip to change its direction. Even if you are not routing out the back, you may use the
cable clip for strain relief to help stabilize the mechanical connection when cardholders or operators
move the device or the cable.
4) Route the cable in the desired direction (e.g., out the back, left, right, or down into the countertop).
5) Connect the other end of the USB cable to the host’s USB port.
6) As soon as the device starts receiving power through USB, it automatically powers on.

2 - How to Connect to Devices
DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 11 of 16 (D100005916-10)
7) Launch the DynaFlex/DynaProx Utility BCR and select a DynaFlex or DynaProx device in the list,
then press the connect button.
8) The Log Messages shows the status of the connection.
9) To disconnect the device, press the Disconnect button.

2 - How to Connect to Devices
DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 12 of 16 (D100005916-10)
2.2 How to Connect Using the Serial Connection
1) For best results, use the cable that is included with the device.
2) Connect the USB-C end of the cable to the DynaProx device and the other end to the PC. This cable
is for powering the device.
3) Connect the 6-pin header end of the Serial cable to the DynaProx device and the other end to the PC
Com port. This cable is for communicating with the device as a COM port. A USB to Serial adapter
cable may be used if the PC is not equipped with a COM port.
4) Launch the DynaFlex/DynaProx Utility BCR and select a Serial DynaProx device in the list, then
press the connect button.
5) The Log Messages shows the status of the connection.
6) To disconnect the device, press the Disconnect button.

3 - How to use the Barcode Reader
DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 13 of 16 (D100005916-10)
3How to use the Barcode Reader
3.1 Barcode Returned Unencrypted
1) Locate a barcode that can be scanned by the device such as a mobile app, screen, or print out.
2) Uncheck Auto-arm Barcode Reader and Encrypt Scan Data.
3) Press the Scan button to begin scanning a barcode.
4) The BCR LED will turn on. Present a barcode near the top center of the device.
5) The BCR LED will turn off after the BCR scan is complete.
Note, if the barcode does not scan, slowly center the barcode. If centered, slowly move the barcode
away from the device. The larger the barcode size, the further away it should be.
6) Barcode data will be shown similar as below.

3 - How to use the Barcode Reader
DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 14 of 16 (D100005916-10)
3.2 Barcode Returned Encrypted
To return the barcode data as encrypted, follow these steps.
1) Locate a barcode that can be scanned by the device such as a mobile app, screen, or print out.
2) Check on Encrypt Scan Data.
3) Press the Scan button to begin scanning a barcode.
4) The BCR LED will turn on. Present a barcode near the top center of the device.
5) The BCR LED will turn off after the BCR scan is complete.
Note, if the barcode does not scan, slowly center the barcode. If centered, slowly move the barcode
away from the device. The larger the barcode size, the further away it should be.
6) Encrypted Barcode data will be shown similar as below.

3 - How to use the Barcode Reader
DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 15 of 16 (D100005916-10)
3.3 Settings
This section describes the settings for this app.
1. Auto-launch URL: When checked, a browser launches if the scanned barcode is a URL, or the app
will launch the browser with the search URL to search for the barcode data if it's a non-URL
2. Auto-arm: When checked, the barcode reader will continuously scan barcodes.
3. Encrypt Scan Data: When checked, the barcode data is returned encrypted. ASCII text is blank.
KSN and Encryption type is filled in.
4. Timeout: Time in seconds from 0 to 255 to re-arm the barcode reader. 0 means no timeout.
5. Default settings: Restores the settings to the default.
6. Save settings: Saves the settings.
7. Collapse Output: Collapses / expands the Output panel.
(1)
(2)
(3)
(7)
(6)
(4)
(5)

3 - How to use the Barcode Reader
DynaFlex, DynaProx| Utility BCR | Manual ( Windows )
Page 16 of 16 (D100005916-10)