Magtek Excella User manual
4. Run Excella Demo
• Navigate to and run C:\Program Files (x86)\MagTek\Excella-STX-
ImageSafe\ Excella-STX_Demo.exe
• Click on the Excella Demo icon to run the demo; the main screen will be
displayed (see Figure 2).
• In the Select Device pull-down menu, choose Excella.EXC001.
• Click on the Connect button.
• Based on the documents you want to read, click on one of the buttons:
• Auto-All: to read and scan a batch of checks from the auto-feeder
• Auto-1: to read and scan a single check from the auto-feeder
• Manual: to read and scan a single check from the Manual Input Slot
5. Reading Checks
Preparing the Checks
When you have a deck of checks that needs to be processed, prepare the
checks as described below:
• Grab the entire deck of checks and lightly tap the bottom of the deck
against a at surface with the objective of aligning the bottom edge of
all the checks in the deck.
• Also, grab the entire deck of checks and lightly tap with your hand the
right edge of the deck with the objective of aligning the leading edge of
all the checks in the deck.
Feeding the Checks Automatically
The Input Hopper can hold up to 70 checks. To feed a deck of checks,
proceed as follows:
• Stack the checks in the Input Hopper as shown in Figure 1.
• Slide the deck forward to the Loading Zone Marker so that all leading
edges are between the arrows as shown in Figure 1.
With a small footprint and striking modern design, Excella is an auto-feed
check reader which captures both the front and back image of checks in
a single pass at 45+ DPM. The automatic feeder has a capacity of up to
70 documents to easily support even the most active check processing
applications. Excella will communicate with the Host system using a USB 2.0
(USB 1.1 compatible) or Ethernet interface.
1. Installation Steps
• Unpack Excella.
• Install ink cartridge (the cartridge is shipped uninstalled).
• Before connecting the Excella scanner, download and unzip the
installation package from here: https://www.magtek.com/support/
excella?tab=software
• Once unzipped, run the Setup.exe installation program. Choose both
the drivers and demo during the installation.
• Depending on your interface, continue with USB CONNECTION, step 2,
or ETHERNET CONNECTION, step 3, below.
2. USB Connection
• Connect the USB interface cable to Excella.
• Connect the round connector from the power supply to Excella.
• Connect the power cord to the socket on the power supply block.
• Connect the three-prong power cord to the AC wall outlet.
• Wait until the three LED’s are illuminated with a steady green.
• Connect the USB interface cable to the PC.
NOTE: When the device is plugged in and detected by the PC, the USB
drivers will be automatically installed.
3. Ethernet Connection
• Connect interface cable (Ethernet) and power cable to Excella.
• Connect power cord to AC wall outlet. Connect interface cable to PC.
• Wait until the three LED’s are illuminated with a steady green.
• Connect the USB interface cable to the PC.
Excella is a web appliance and it offers several functions and features in
a built-in Web page accessible through a Web browser. For example, if
Excella’s default Ethernet device IP address is 192.168.10.100, type the
“http://192.168.10.100” in your web browser to access Excella’s web page.
On the main menu, the Conguration page offer options to setup the
Network and Ethernet congurations. Additionally, an option is provided to
save and restore device congurations.
Excella - USB or Ethernet
Small Document Scanner
Quick Installation Guide
Setup and Installation
MagTek®Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com
Install Print Cartridge
• Pull the Printer/Cartridge cover open to expose the Printer/Cartridge.
• Push the Printer/Cartridge green latch down.
• Locate the alignment pegs on the Printer/Cartridge and the guide
holes on the Printer Base.
• Install the Printer/Cartridge on the Printer Base by sliding the
alignment pegs into the guide holes.
• Raise the green latch to lock the Printer/Cartridge in position.
• Close the Printer/Cartridge cover.
Troubleshooting/LEDs
The LED indicators are shown in Figure 5. All three LEDs are able to show
three colors: green, red, or amber. Each LED indicator has been assigned a
specic reporting function.
• Front LED: reports MICR read status
• Middle LED: reports path status
• Rear LED: reports unit status
Front LED
(MICR status)
Middle LED
(Path status)
Rear LED
(Unit status)
Description
Amber Amber Amber Unit is initializing
Green Green Green Power on, everything is OK
X X Flash Amber Initializing network con-
nection
Flash Red X X After check read: MICR
read error
Flash Green X X After check read: good
MICR read
Flash Red/
Green
X X MICR noise detected (if
enabled): relocate unit
XAmber XLeft or right access door
unlatched (if feature is
installed): close and latch
access guides
XFlash Red XPaper jam: remove jam and
hit operator button to clear
Note: More detailed instructions can be found in Excella’s Installation and
Operation Manual (P/N 99875310).
Opening and Closing the Unit
OPENING THE UNIT
• The Left Access Door, the Right Access Door and the Printer/Cartridge
Cover, shown in Figure 2, can be opened to provide access to the
check path and both scan bars. Open the unit as described as follows:
• Open the Left Access Door by placing the thumb on the Indent and
the nger(s) on the Tab as shown in Figure 2 and squeezing, and then
gently pull the Door open.
• Open the Right Access Door, in the same manner, by placing the
thumb on the Indent and the nger(s) on the tab, and squeezing and
then gently pull the guide open.
• Open the Printer/Cartridge Cover by pulling the Cover from the Left
Door as shown in Figure 3.
CLOSING THE UNIT
• If the Left Access Door or the Right Access Door has been opened,
close the access door as described below:
• Push to close the access door (Left or Right) to its normal operating
position (as show in Figure 4).
• If the Printer/Cartridge Cover is open on the Left Access Door, rst
close the printer cover and then close the access door as described in
step 1 above.
• Push down on the tab of the access door (as shown in Figure 4) If
the tab was not latched, a “click” sound will be heard as feedback to
indicate the access guide is securely closed.
• The LED indicator will ash if the access door is improperly closed.
MagTek®, MagnePrint®, and MagneSafe® are registered trademarks of MagTek, Inc.
MAGTEK: Registered to ISO 9001:2015 © Copyright 2021 MagTek, Inc. PN D99800048 rev 30 3/21
MagTek®Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com
Use and LEDs
Other Magtek Scanner manuals
