Majestic Sc36 Mounting instructions

Majestic Fireplaces®SR/SC Series

12345678901234567890123

234567890123456789012

12345678901234567890123

SR/SC Series

Woodburning Fireplace

For Models:

SR36

SR42

SC36

SC42

For use in U.S./Canada

Underwriter's Laboratories Report No. MH6018 DO NOT DISCARD THIS MANUAL:

Retain for future use.

™

7412948 4/02 Rev. 7

Homeowner's Installation and Operating Manual

Majestic Fireplaces®SR/SC Series

Safety Information

PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING FIREPLACE.

IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to

follow these instructions may result in a possible fire hazard and will void the warranty.

Description

The SR/SC Series fireplaces are solid fuel, woodburn-

ing premium fireplaces. The SR36/42 are radiant

clean-face models and the SC36/42 are circulating

models with removable grilles (louvers). Both models

are fully insulated fireplaces.

Precautions

Vermont Castings, Majestic Products fireplaces and

component parts have been highly tested and will

operate safely when installed in accordance with

instructions provided in this manual. Carefully read

and understand all instructions before beginning

installation.

If you notice any damage to fireplace or component

parts, immediately report damage to your Vermont

Castings, Majestic Products dealer.

Only use Vermont Castings, Majestic Products compo-

nents or the warranty will be voided and a fire hazard

may be created.

Vermont Castings, Majestic Products warranty will be

voided by and Vermont Castings, Majestic Products

disclaims any responsibility for the following actions:

• Installation of any damaged fireplace or

chimney component;

• Modification of fireplace, chimney assembly

or any component parts thereof; (except for

chase flashings as detailed in Vermont Castings,

Majestic Products Chimney Top installation

instructions).

• Installation other than as instructed by

Vermont Castings, Majestic Products; or

• Installation and/or use of any component

part not manufactured or approved by

Vermont Castings, Majestic Products in

combination or assembly with a Vermont

Castings, Majestic Products fireplace sys-

tem, notwithstanding any independent

testing laboratory or other third party ap-

proval of such component parts or acces-

sory.

Any such action may possibly cause a fire hazard.

Consult local building codes to ensure that you are in

compliance before installing the fireplace.

Fireplaces must be vented to the out-of-doors.

Do not obstruct or modify air inlets/outlets in any

manner.

Do not install combustible materials on any of the

black fireplace surround.

Burn only solid wood fuel or gas logs.

Do not install a solid fuel burning insert or other

products not specified for use with this fireplace.

These fireplaces are not approved for installation

in mobile homes.

Drafts

The fireplace should not be located in areas that

create drafts (ie: frequently opened doors and central

heating air inlets/outlets) that hamper the normal flow

of air into the fire.

Gas Logs

If you plan to install a gas log, the gas line should be

installed before framing the fireplace. The gas line

must be installed by a certified gas line installer.

Safety Information . . . . . . . . . . . . . . . . . . 2

Specifications and Framing. . . . . . . . . . . 3

Parts Identification. . . . . . . . . . . . . . . . . . 5

Chimney Requirements. . . . . . . . . . . . . . 6

Planning Information . . . . . . . . . . . . . . . . 7

Installation . . . . . . . . . . . . . . . . . . . . . . . . 8

Replacement Parts . . . . . . . . . . . . . . . . 19

Accessories. . . . . . . . . . . . . . . . . . . . . . 20

Table Of Contents

SR36 / SR42

SC36 / SC42

Listed

UL / ULc127

Standard for Factory Built Fireplaces

Majestic Fireplaces®SR/SC Series

FP590

FP589

Fig. 2 SC36 Series specifications and framing.

SC36 Series Woodburning Fireplace — Circulating Model

SR36 Series Woodburning Fireplace

Fig. 1 SR36 Series specifications and framing.

36"

(914mm)

14⁵⁄₈"

(372mm)

15 ³⁄₈"

(391mm)

9¹⁄₂"

(241mm)

40"

(1016mm)

36⁵⁄₈"

(930mm)

(76mm)

⁵⁄₈"

(16mm)

⁵⁄₈" (16mm)

48¹⁄₂" (1232mm)

¹⁄₂" (13mm)

¹⁄₂"

68¹⁄₂" (1740mm)

8¹⁄₄"

(210mm)

22"

(559mm)

22¹⁄₂"

(572mm)

22" (559mm)

19 ³⁄₄"

(502mm)

21"

(533mm)

40³⁄₄"

(1035mm)

(203mm)

7³⁄₄"

(197mm)

7¹⁄₂"

(191mm)

7¹⁄₂"

(191mm)

Outside

Air

Gas Line

Access

Gas Line

Access

Electrical

Access

Recessed

Nailing

Flange

11" DIA.

Rough Opening Width 41"

Rough

Opening

Height

Rough

Opening

Depth

34¹⁄₂" (876mm)

(1041mm)

⁵⁄₈" (16mm)

¹⁄₂" (13mm)

¹⁄₂"

36"

(914mm)

35¹⁄₄"

(895mm)

40" (1016mm)

⁵⁄₈"

(16mm)

19 ³⁄₄"

(502mm)

1³⁄₄"

(45mm)

35¹⁄₂" (902mm)

21"

(533mm)

7³⁄₄"

(197mm)

7¹⁄₂"

(191mm)

Recessed

Nailing

Flange

11" DIA.

Rough Opening Width 41"

Rough

Opening

Height

Rough

Opening

Depth

Gas Line

Access

48¹⁄₂" (1232mm)

34¹⁄₂" (876mm)

68¹⁄₂" (1740mm)

8¹⁄₄"

(210mm)

22"

(559mm)

22¹⁄₂"

(572mm)

22" (559mm)

40³⁄₄"

(1035mm)

14⁵⁄₈"

(372mm)

15 ³⁄₈"

(391mm)

9¹⁄₂"

(241mm)

36⁵⁄₈"

(930mm)

(76mm)

(203mm)

7¹⁄₂"

(191mm)

Outside Air

Gas Line

Access

(1041mm)

Electrical Access

Majestic Fireplaces®SR/SC Series

SR42 Series Woodburning Fireplace

Fig. 3 SR42 Series specifications and framing.

FP591

Fig. 4 SC42 Series specifications and framing.

SC42 Series Woodburning Fireplace — Circulating Model

FP592

42"

(1067mm)

46"

(1168mm)

36⁵⁄₈"

(930mm)

⁵⁄₈"

(16mm)

⁵⁄₈" (16mm)

¹⁄₂" (13mm)

¹⁄₂"

19³⁄₄"

(502mm)

21"

(533mm)

7³⁄₄"

(197mm)

7¹⁄₂"

(191mm)

Gas Line

Access

Recessed

Nailing

Flange

11" DIA.

Rough Opening Width 47"

Rough

Opening

Height

Rough

Opening

Depth

50" (1270mm)

36" (914mm)

70¹⁄₂" (1791mm)

8¹⁄₄"

(210mm)

22"

(559mm)

22¹⁄₂"

(572mm)

26¹⁄₄"

(667mm)

40³⁄₄"

(1035mm)

14⁵⁄₈"

(372mm)

15⁵⁄₈"

(397mm)

9¹⁄₂"

(241mm)

(76mm)

(203mm)

7¹⁄₂"

(191mm)

Outside

Air

Gas Line

Access

Electrical

Access

(1194mm)

7¹⁄ ₂ "

(191mm)

50" (1270mm)

42"

(1067mm)

35¹⁄₄"

(895mm)

46" (1168mm)

⁵⁄₈"

(16mm)

⁵⁄₈" (16mm)

¹⁄₂" (13mm)

¹⁄₂"

19³⁄₄"

(502mm)

1³⁄₄"

38" (965mm)

21"

(533mm)

7³⁄₄"

(197mm)

Recessed

Nailing

Flange

11" DIA.

Rough Opening Width 47"

Rough

Opening

Height

Rough

Opening

Depth

Gas Line

Access

50" (1270mm)

36" (914mm)

70¹⁄₂" (1791mm)

8¹⁄₄"

(210mm)

22"

(559mm)

22¹⁄₂"

(572mm)

26¹⁄₄"(667mm)

40³⁄₄"

(1035mm)

14⁵⁄₈"

(372mm)

15³⁄₈"

(397mm)

9¹⁄₂"

(241mm)

36⁵⁄₈"

(930mm)

(76mm)

(203mm)

7¹⁄₂"

(191mm)

Outside Air

Gas Line

Access

Electrical

Access

(1194mm)

Majestic Fireplaces®SR/SC Series

Chase Installation

Insulation methods shown are optional

for cold climate, not a requirement for

unit operation.

FP554

Fig. 5 Fireplace and chase parts identification.

;;

;

TERMINATION CAP

STORM COLLAR

PAN FLASHING

DRAFTSTOP

FIRESTOP

STANDOFF

NAILING FLANGE

GAS LINE ACCESS

(both sides)

ELECTRICAL

ACCESS

OUTSIDE AIR

COVER PLATE

DAMPER CONTROL

SURROUND

METAL SAFETY STRIPS

(1, 2 or 3 pieces)

GAS LINE

KNOCKOUT

(both sides)

;

;;

;

BATT INSULATION

(cut out around

firestop)

SCREEN

GRATE

FIREBOX

CEILING LEVEL

Majestic Fireplaces®SR/SC Series

Chimney Requirements - Offset Installations

0000 0 3" 11"

1000 0 8¹⁄₄"20"

0100 0 11¹⁄₄"25¹⁄₄"

2000 0 13¹⁄₂"29¹⁄₄"

1100 0 16¹⁄₂"34¹⁄₄"

0010 0 20¹⁄₄"40³⁄₄"

2100 0 21³⁄₄"43¹⁄₂"

0001 0 26¹⁄₄"51¹⁄₄"

0110 0 28¹⁄₂"55¹⁄₄"

1001 0 31¹⁄₂"60¹⁄₄”

0101 0 34¹⁄₂"65¹⁄₂"

0020 0 37¹⁄₂"70³⁄₄"

1101 1 41¹⁄₂"77³⁄₄"

0011 1 45" 83³⁄₄"

0120 1 47¹⁄₄"87¹⁄₂"

0002 1 51" 94"

0111 1 53¹⁄₄"98"

0030 1 56¹⁄₄"103¹⁄₄"

0102 1 59¹⁄₄"108¹⁄₂"

0021 1 62¹⁄₄"113¹⁄₂"

0130 1 64¹⁄₂"117¹⁄₂"

0012 1 68¹⁄₄"124"

0121 1 70¹⁄₂"128"

0003 1 74¹⁄₄"134¹⁄₂"

01122 78"140³⁄₄"

00312 81" 146"

01032 84"151¹⁄₄"

00222 87"156¹⁄₂"

01312 89¹⁄₄"160¹⁄₄"

00132 93"166³⁄₄"

01222 95¹⁄₄"170³⁄₄"

00042 99¹⁄₄"177³⁄₄"

01132101¹⁄₄"181³⁄₄"

00322104¹⁄₄"186¹⁄₄"

01042107¹⁄₄"191¹⁄₂"

00232110¹⁄₄"196³⁄₄"

01323 114" 203¹⁄₄"

00143117³⁄₄"209³⁄₄"

01233 120" 213¹⁄₂"

00053123³⁄₄"220"

30˚ Elbow Offsets

1' 1¹⁄₂'3' 4'

Chimney

Support

Offset Rise

Notes: G + H cannot exceed 20 feet.

Air Space Clearances: SK8 (2-wall) = 1¹⁄₂" and "S" Series (3-wall) = 2"

Illustration Key

The following safety rules apply to

offset installations (letters correspond

with illustration above):

A. Height of the chimney is measured

from the hearth to the chimney exit.

SR/SC36 SR/SC42

Maximum: 90' 90'

Minimum:

Without Elbows 12' 6" 12' 6"

With 2 Elbows* 14' 6" 14' 6"

With 4 Elbows* 21' 0" 21' 0"

B. Do not use more than 4 elbows per

chimney.

Attach the straps of the return (top)

elbow to a structural framing member.

The offset (first) elbow of any pair does

not have straps.

IWF269

C. The chimney cannot be more than 30˚

(45˚ in Canada) from the vertical plane in

any installation*.

D. The maximum length of the angled run

of the total chimney system is 20 feet. (G

plus H cannot exceed 20 feet.)

E. A chimney support (Model SKCS8) is

required every 6 feet of angled run of

chimney. Chimney supports are required

for every 30 feet and 60 feet (SK8 pipe)

or 20 feet and 40 feet (3-wall pipe) of

vertical chimney height above the hearth.

Determine the offset distance of your

chimney arrangement from the centerline

of the fireplace to the centerline of the

chimney where it is to pass through the

first ceiling.

Note: This offset distance may not be

your full offset distance. See Examples 2

and 3.

OFFSET

RISE

IWF282

*In Canada, two (2) SK845 are allowed.

Fig. 6 Chimney system requirements.

DRISE

OFFSET

6 FT.

HEARTH

FLOOR

CHIMNEY

SECTION

CHIMNEY FLUE EXIT

ELBOW

30˚

OFFSET

ELBOW

30˚

OFFSET

ELBOW

30˚

RETURN

ELBOW

30˚

RETURN

ELBOW

SKCS8

SUPPORT

Example 1 Example 2 Example 3

Majestic Fireplaces®SR/SC Series

Planning Information

Preplanning an installation is very important to ensure

safety and to save time and money. An installer must

predetermine where a fireplace will be set and how the

chimney system will be run.

Mounting The Fireplace

A fireplace may only be mounted on the following

surfaces:

1. Aflat combustible surface.

2. A raised wooden platform.

3. A concrete block or other solid object placed be-

neath each of the four (4) corners of the fireplace.

The fireplace must be spaced 1/2 inch from a com-

bustible back wall and 1/2 inch from a combustible

side wall or support. (Fig. 20, Page 14)

Planning The Chimney Run

5. No more than 2 offsets (4 total 30˚ elbows in U.S./or

2 total 45˚ elbows in Canada) per fireplace may be

used.

6. A guy wire stabilizer is required for chimneys

extending more than 6 feet above a roof line.

The Ten Foot Rule

Major U.S. building codes specify a minimum chimney

height above the roof top. The “Ten Foot Rule” is a fire

safety rule and not a draft rule. To ensure proper draft,

it is recommended that you always meet or exceed the

“Ten Foot Rule,” especially when installing a termina-

tion on a high pitch roof. (Fig. 8)

The key points of the "Ten Foot Rule" are:

1. If the horizontal distance from the center of the

chimney to the peak of the roof is 10 feet or less,

the top of the chimney must be at least 2 feet above

the peak of the roof, but never less than 3 feet in

height above the highest point where it passes

through the roof.

2. If a horizontal distance from the center of the

chimney to the peak of the roof is more than 10 feet,

a chimney height reference point is established that

is on the surface of the roof a distance of 10 feet

from the center of the chimney in a horizontal plane.

The top of the chimney must be at least 2 feet

above the reference point, but never less than 3 feet

in height above the highest point where it passes

through the roof.

Determine how the chimney will be run, length of run

and chimney components required to complete the

job. (Fig. 6) Never install a chimney below minimum

heights.

In planning a chimney system, it is important to know:

1. The height of a chimney is measured from the

hearth to the exit point on the termination.

2. A chimney cannot be offset more than 30 degrees

from a vertical plane.

3. A chimney may run straight up or it may be neces-

sary to offset it to avoid obstructions.

4. The maximum length of an angled run (total chim-

ney system) is 20 feet.

LTMODEL SK

2WALL CHIMNEY

TOTAL

LENGTH

(LT)

INSTALLED

LENGTH

(L1)

SK81

SK818

SK83

SK84

11¹⁄₂

17¹⁄₂

35¹⁄₂

47¹⁄₂

10¹⁄₂

16¹⁄₂

34¹⁄₂

46¹⁄₂

Fig. 7 Installed lengths of chimney sections. WF288

AC246

Fig. 8 Ten Foot Rule illustration.

2' MIN.

MIN.

0 TO10'

MIN.

0 TO10'

REFERENCE

POINT

Majestic Fireplaces®SR/SC Series

■1. Insulating Fireplace Enclosure

For Cold Climates

If you live in a cold climate, it is not required but

highly recommended that you insulate fire-

place enclosure to eliminate cold air penetration

as much as possible.

Insulate base of fireplace with a non-combus-

tible insulation rated for a minimum of 300

degrees F. Insulating is very important for

outside wall installations over a concrete slab. If

fireplace is installed on a platform, insulation

should be placed on top of the platform before

fireplace is set. (Fig. 10)

When a fireplace is installed in a chase or on a

outside wall, enclosure should be treated like

any outside wall in a home. Insulation should be

installed on the inside wall as well as the

outside wall(s). In a chase, it is also a good idea

to install a firestop at the first ceiling level above

the fireplace and enclose the chase with

sheeting material. Insulation may then be

installed above sheeting material to assure the

space around the fireplace is totally protected.

(Fig. 5)

When installing the chimney, DO NOT caulk

between outer pipe and firestop. It is vital that

some air be allowed to flow through this very

thin gap.

CAUTION: WHEN INSTALLING A FIRE-

PLACE IN AN INSULATED ENCLOSURE, BE

SURE ALL REQUIRED AIR SPACES ARE

MAINTAINED. (Fig. 20, Page 14)

Installation

Chimney Supports

The chimney system is supported by the fireplace for

vertical chimney heights less than 30 feet above the

hearth. Chimney supports are required if the vertical

height exceeds 30 feet with SK8 chimneys or 20 feet

with 3-wall chimneys. Locate chimney supports at

ceiling holes or other structural framing at 30 foot

(SK8) or 20 foot (3-wall) heights. Spacing between

chimney supports must not exceed 30 feet(SK8) or 20

foot (3-wall). Use Chimney Support Model SKCS8.

(Note: the SKCS8 can not be mounted directly to

the fireplace.) Support provided by elbow straps

fulfills the support requirement only if they are spaced

as previously described. (A chimney support is 2¹⁄₂"

long when installed.)

Angled chimney runs require a support every six (6)

feet in addition to the elbow straps. Chimney supports

are used for this function. (Fig. 9)

Chase Installation

A chase is a vertical box-like structure which encloses

the fireplace and/or chimney. Chases are typically

built on the outside of the house with fireplace opening

cut into the outer wall of a room. (Fig. 5, Page 5)

If you need help in determining fireplace location or

how the chimney system should be run, contact your

Vermont Castings, Majestic Products dealer for

assistance.

FP284

Fig. 9 Chimney support installation

CHIMNEY

SUPPORT

STRAP

SKCS8

Majestic Fireplaces®SR/SC Series

■2. Framing

Framing can be constructed before or after the fire-

place is set in place, however, most installers build the

frame before setting the fireplace.

Frame fireplace with 2 X 4 lumber or heavier materials.

Refer to framing dimensions in Figures 1, 2, 3 or 4 for

basic fireplace specifications.

Note: Framing should be positioned to accommodate

wall covering and fireplace facing material.

■3. Installing Electrical Wire

(for Circulator Models)

If a circulating fireplace is to be installed, run the 120

VAC, 60 Hz wiring to the left side of installation.

Wiring must be completed before the fireplace is

secured and finish material applied.

Remove the cover plate and electrical knock-out on

the lower left side of the fireplace and set aside. Follow

the instructions on Page 10 for proper wiring and

installation of the EB1.

If the fan kit is not being installed with the fireplace, it

is highly recommended that 120 VAC supply be made

available since someone may elect to install a blower

at a later date.

FP555

Fig. 10 Insulating between platform and fireplace.

;;;;

;

;;

INSULATION

PLATFORM

HARD

FLAT

SURFACE

Option For Circulating Models Only —

EB1 (Receptacle) Hook-Up

• Wiring should be installed by a certified

electrician.

• Turn off circuit breaker before wiring models.

Once fireplace is secured, complete wiring the fan

kit. Remove knockout in the center of the back of

the EB1 and install listed cable clamps. Feed

electrical wire through listed cable clamp leaving

approximately six (6) inches of wire exposed

through the EB1. Secure listed cable clamp to the

wire.

Attach white wire from power source to one (1)

wire of receptacle and secure with nut. Attach

black wire from power source to the other wire of

receptacle and secure with nut.Be sure nuts are

secured tightly.

Secure EB1 assembly to inside of electrical box

coverplate using two screws. Attach cover to face

of the EB1 while being careful to position excess

wire completely within the EB1, then attach

coverplate to fireplace.

Install Fan Kit Assembly

Refer to optional Model FK12 fan kit assembly

installation instructions for field installation.

■4. Chimney Set-up

Since you have already preplanned the chimney run,

you should know exactly how the installation is to be

accomplished — how much pipe is required, the

number of elbows, if any, and type of termination to

be used.

CAUTION: REPORT TO YOUR DEALERS ANY

PARTS DAMAGED IN SHIPMENT, SPECIFICALLY

CHECK THE END CONNECTION OF CHIMNEY

SECTIONS AND ELBOWS.

Note: Fireplaces may use Vermont Castings, Majes-

tic Products model SK8, or Model S (three wall)

chimney systems. The SR/SC Series Fireplace will

accept the SK8 chimney system as is; but a TWABR

adapter collar is required when using the Model S

(triple wall) chimney system. The installation proce-

dure described in this manual applies only to the

SK8 system. Either chimney system may be used,

but may not be mixed.

Majestic Fireplaces®SR/SC Series

Straight-Up Chimney Installation

To mark the centerline of the flue, put the fireplace in

final position and measure out from the wall: 9¹⁄₄

inches. Mark a spot on the ceiling directly above the

fireplace. Draw a line parallel to the back wall through

this mark. (Fig. 11)

Using a plumb bob positioned directly over center

point of fireplace flue collar, mark the ceiling to estab-

lish the chimney center point. (Fig. 11)

Offset Installation

In order to clear an obstruction, it may be necessary to

offset chimney from vertical. This is accomplished by

using Majestic elbows. Use the

30˚ Offset Elbow

table

on Page 6 to determine proper offset and parts

required.

Each offset requires two (2) elbows. The second

elbow is equipped with support straps. It is very

important to install the second elbow in each offset as

close to the ceiling or support as possible so that the

elbow straps can be secured to framing members to

help support the weight of the chimney.

Determine offset distance of your chimney arrange-

ment from centerline of fireplace to centerline of

chimney where it is to pass through ceiling.

Locate center point of the chimney on ceiling as

though a straight up chimney arrangement is to be

used. Measure your offset dimension from straight up

chimney center point on ceiling.

Ceiling Chimney Hole/

Possible Obstructions

The size of the hole in ceiling will vary with the angle at

which the chimney passes through ceiling.

Drive a nail up through ceiling at marked chimney

center point. Go to floor above and see where hole

will be cut. Check to see where existing ceiling joists

and other possible obstructions are located...i.e.

wiring, plumbing etc... If necessary, re-position chim-

ney and/or fireplace to avoid obstructions.

Cutting the Hole

Cover fireplace collar opening and cut proper sized

chimney hole in chimney. The SK8 pipe allows you to

run pipe through a typical 16” on center joist without

cutting joists.

Framing the Ceiling Hole

Frame the ceiling chimney hole as shown in Figure 12.

It is good practice to use framing lumber that is the

same size as the ceiling joists; this is a requirement at

attic level.

Fig. 12 Typical frame for ceiling chimney hole.

FP551

;;

;;;;

CEILING

CHIMNEY

HOLE

NEW

FRAMING

MEMBERS

EXISTING

CEILING

JOISTS AB AB

FP556

Fig. 11 Locate centerline of chimney with plumb line.

ACTUAL

CENTERPOINT

CHIMNEY CENTERLINE

IMAGINARY

CENTERPOINT

PLUMB LINE

PLUMB BOB

9¹⁄₄"

This manual suits for next models

Table of contents

Other Majestic Indoor Fireplace manuals

Majestic

Majestic RC36 Planning guide

Majestic

Majestic 300DVB User manual

Majestic

Majestic VL18 User manual

Majestic

Majestic PEARL36STIN User manual

Majestic

Majestic MDVI30IN User manual

Majestic

Majestic ECHEL36IN User manual

Majestic

Majestic 380IDVNVC User manual

Majestic

Majestic Thulman L28A User manual

Majestic

Majestic ASH36 User manual

Majestic

Majestic NVC36 Operating instructions

Majestic

Majestic 500DVM Manual

Majestic

Majestic 400DVBL User manual

Majestic

Majestic 33ISDG User manual

Majestic

Majestic DBDV36IN User manual

Majestic

Majestic B36LA Manual

Majestic

Majestic MHC28 User manual

Majestic

Majestic Royalton BE42 User manual

Majestic

Majestic NVBR36 User manual

Majestic

Majestic MARQUIS MARQ36IN-B User manual

Majestic

Majestic SA36R User manual

Majestic

Majestic 500DVKST User manual

Majestic

Majestic 500DVKHL User manual

Majestic

Majestic MI 1200 Quick start guide

Majestic

Majestic 20ILDVNV User manual

Popular Indoor Fireplace manuals by other brands

Napoleon

Napoleon NEFL42CHD-1 manual

Masport

Masport WOOD FIRE installation guide

JAYLINE

JAYLINE SS280 Installation & operation instructions

Heat-N-Glo

Heat-N-Glo SL-32S Installation

kozy heat

kozy heat Bellingham 52 quick start guide

Paragon Fires

Paragon Fires ROOM SEALED INSET LIVE FUEL EFFECT GAS FIRE owner's manual

Monessen Hearth

Monessen Hearth LCUF32CR-B Installation & owner's manual

PuraFlame

PuraFlame Galena owner's manual

Dimplex

Dimplex Toluca Deluxe instruction manual

SEI

SEI TENNYSON FA8544AO Assembly instructions

Dru

Dru G25 installation manual

Capital fireplaces

Capital fireplaces Designline DL700 Installation and user instructions

IronStrike

IronStrike VINTAGE VINT-DVS-U Installation and operation

ACR Heat

ACR Heat HERITAGE N25 Installation and operating instruction manual

European Home

European Home HVF-42 Installation, operation and owner's manual

Quadra-Fire

Quadra-Fire MTVERNINSAE-MBK Owner's manual operation & care

Harman Home Heating

Harman Home Heating Accentra Insert Installation & operating manual

Trimline Fires

Trimline Fires Zircon 1024 installation instructions

Majestic SC36 Mounting instructions

Popular Indoor Fireplace manuals by other brands