Makita DUC304 User manual

INSTRUCTION MANUAL
MANUEL D'INSTRUCTION
MANUAL DE INSTRUCCIONES
Cordless Chain Saw
Tronçonneuse sans Fil
Electrosierra Inalámbrica
DUC204
DUC254
DUC304
IMPORTANT: Read Before Using.
IMPORTANT : Lire avant usage.
IMPORTANTE: Lea antes de usar.

2ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: DUC204 DUC254 DUC304
Overall length (without guide bar) 256 mm
(10-1/8″)
Rated voltage D.C. 18 V
Net weight 2.7 - 3.2 kg
(6.0 - 7.1 lbs)
Standard guide bar length 200 mm
(8″)
250 mm
(10″)
300 mm
(12″)
Recommended guide
bar length
with 90PX 200 - 300 mm
(8″ - 12")
with 80TXL -250 mm
(10″)
-
Applicable saw chain type
(refer to the table below)
90PX 90PX
80TXL
90PX
Sprocket
(90PX)
Number of teeth 6
Pitch 3/8″
Sprocket
(80TXL)
Number of teeth 7
Pitch 0.325″
Chain speed 0 - 24.8 m/s
(0 - 1,490 m/min)
(0 - 4,880 ft/min)
Chain oil tank volume 140 cm3 (4.7 oz)
• Due to our continuing program of research and development, the specications herein are sub-
ject to change without notice.
• Specications may dier from country to country.
• The weight may dier depending on the attachment(s), including the battery cartridge. The light-
est and heaviest combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge BL1815N / BL1820B / BL1830 / BL1830B /
BL1840B / BL1850B / BL1860B
Charger DC18RC / DC18RD / DC18RE / DC18SD /
DC18SE / DC18SF / DC18SH
• Some of the battery cartridges and chargers listed above may not be available depending on your
region of residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other
battery cartridges and chargers may cause injury and/or re.

3ENGLISH
Saw chain, guide bar, and sprocket combination
Saw chain type 90PX
Number of drive links 33 40 46
Guide bar Guide bar length 200 mm
(8″)
250 mm
(10″)
300 mm
(12″)
Cutting length 171 mm
(6-3/4″)
235 mm
(9-1/4″)
292 mm
(11-1/2″)
Part No. 161848-6 161846-0 165245-8
Pitch 3/8″
Gauge 1.1 mm
(0.043″)
Type Sprocket nose bar
Sprocket Number of teeth 6
Pitch 3/8″
Saw chain type 80TXL
Number of drive links 46
Guide bar Guide bar length 250 mm (10″)
Cutting length 232 mm (9-1/8″)
Part No. 162985-9
Pitch 0.325″
Gauge 1.1 mm (0.043″)
Type Sprocket nose bar
Sprocket Number of teeth 7
Pitch 0.325″
WARNING: Use appropriate combination of the guide bar, saw chain and sprocket. Otherwise
personal injury may result.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings and
all instructions. Failure to follow the warnings
and instructions may result in electric shock,
re and/or serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Work area safety
1. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
3. Keep children and bystanders away
while operating a power tool. Distractions
can cause you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodied plugs
and matching outlets will reduce risk of elec-
tric shock.
2. Avoid body contact with earthed or
grounded surfaces, such as pipes, radia-
tors, ranges and refrigerators. There is an
increased risk of electric shock if your body
is earthed or grounded.

4ENGLISH
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
4. Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
5. When operating a power tool outdoors,
use an extension cord suitable for out-
door use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
6. If operating a power tool in a damp
location is unavoidable, use a ground
fault circuit interrupter (GFCI) protected
supply. Use of a GFCI reduces the risk of
electric shock.
Personal Safety
1.
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the inuence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
2. Use personal protective equipment.
Always wear eye protection. Protective
equipment such as a dust mask, non-skid
safety shoes, hard hat or hearing protection
used for appropriate conditions will reduce
personal injuries.
3. Prevent unintentional starting. Ensure
the switch is in the o-position before
connecting to power source and/or bat-
tery pack, picking up or carrying the tool.
Carrying power tools with your nger on the
switch or energising power tools that have
the switch on invites accidents.
4.
Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
5. Do not overreach. Keep proper footing
and balance at all times. This enables bet-
ter control of the power tool in unexpected
situations.
6. Dress properly. Do not wear loose cloth-
ing or jewellery. Keep your hair, clothing,
and gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
7. If devices are provided for the connec-
tion of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of dust collection
can reduce dust-related hazards.
Power tool use and care
1. Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.
2. Do not use the power tool if the switch
does not turn it on and o. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
3. Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety mea-
sures reduce the risk of starting the power
tool accidentally.
4. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
5.
Maintain power tools. Check for misalign-
ment or binding of moving parts, break-
age of parts and any other condition that
may aect the power tool’s operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
6. Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
7. Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for oper-
ations dierent from those intended could
result in a hazardous situation.
Battery tool use and care
1. Recharge only with the charger specied
by the manufacturer. A charger that is suit-
able for one type of battery pack may create
a risk of re when used with another battery
pack.
2. Use power tools only with specically
designated battery packs. Use of any
other battery packs may create a risk of
injury and re.
3. When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects, that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a re.

5ENGLISH
4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, ush with
water. If liquid contacts eyes, addition-
ally seek medical help. Liquid ejected from
the battery may cause irritation or burns.
5.
Do not use a battery pack or tool that is
damaged or modied. Damaged or modied
batteries may exhibit unpredictable behaviour
resulting in re, explosion or risk of injury.
6. Do not expose a battery pack or tool to
re or excessive temperature. Exposure
to re or temperature above 130 °C may
cause explosion.
7. Follow all charging instructions and do
not charge the battery pack or tool out-
side the temperature range specied in
the instructions. Charging improperly or
at temperatures outside the specied range
may damage the battery and increase the
risk of re.
Service
1. Have your power tool serviced by a qual-
ied repair person using only identical
replacement parts. This will ensure that
the safety of the power tool is maintained.
2. Follow instruction for lubricating and
changing accessories.
3. Keep handles dry, clean and free from oil
and grease.
4. Do not modify or attempt to repair the
appliance or the battery pack except as
indicated in the instructions for use and
care.
Cordless Chain saw safety warnings
1. Keep all parts of the body away from the
saw chain when the chain saw is operat-
ing. Before you start the chain saw, make
sure the saw chain is not contacting
anything. A moment of inattention while
operating chain saws may cause entangle-
ment of your clothing or body with the saw
chain.
2. Always hold the chain saw with your
right hand on the top handle and your
left hand on the front handle. Holding the
chain saw with a reversed hand congura-
tion increases the risk of personal injury and
should never be done.
3. Hold the power tool by insulated grip-
ping surfaces only, because the saw
chain may contact hidden wiring. Saw
chains contacting a "live" wire may make
exposed metal parts of the power tool "live"
and could give the operator an electric
shock.
4. Wear safety glasses and hearing protec-
tion. Further protective equipment for head,
hands, legs and feet is recommended.
Adequate protective clothing will reduce
personal injury by ying debris or accidental
contact with the saw chain.
5. Always keep proper footing.
6. When cutting a limb that is under tension
be alert for spring back. When the tension
in the wood bres is released the spring
loaded limb may strike the operator and/or
throw the chain saw out of control.
7. Use extreme caution when cutting brush
and saplings. The slender material may
catch the saw chain and be whipped toward
you or pull you o balance.
8. Carry the chain saw by the front handle
with the chain saw switched o and
away from your body. When transporting
or storing the chain saw always t the
guide bar cover. Proper handling of the
chain saw will reduce the likelihood of acci-
dental contact with the moving saw chain.
9.
Follow instructions for lubricating, chain
tensioning and changing accessories.
Improperly tensioned or lubricated chain may
either break or increase the chance for kickback.
10. Keep handles dry, clean, and free from
oil and grease. Greasy, oily handles are
slippery causing loss of control.
11. Cut wood only. Do not use chain saw
for purposes not intended. For example:
do not use chain saw for cutting plastic,
masonry or non-wood building materials.
Use of the chain saw for operations dierent
than intended could result in a hazardous
situation.
12.
Causes and operator prevention of kickback:
Kickback may occur when the nose or tip
of the guide bar touches an object, or when
the wood closes in and pinches the saw
chain in the cut. Tip contact in some cases
may cause a sudden reverse reaction, kick-
ing the guide bar up and back towards the
operator. Pinching the saw chain along the
top of the guide bar may push the guide bar
rapidly back towards the operator. Either of
these reactions may cause you to lose con-
trol of the saw which could result in serious
personal injury. Do not rely exclusively upon
the safety devices built into your saw. As
a chain saw user, you should take several
steps to keep your cutting jobs free from
accident or injury.
Kickback is the result of tool misuse and/or
incorrect operating procedures or conditions
and can be avoided by taking proper pre-
cautions as given below:

6ENGLISH
• Maintain a rm grip, with thumbs and
ngers encircling the chain saw han-
dles, with both hands on the saw and
position your body and arm to allow
you to resist kickback forces. Kickback
forces can be controlled by the opera-
tor, if proper precautions are taken. Do
not let go of the chain saw.
Fig.1
• Do not overreach and do not cut above
shoulder height. This helps prevent
unintended tip contact and enables
better control of the chain saw in unex-
pected situations.
• Only use replacement bars and
chains specied by the manufacturer.
Incorrect replacement bars and chains
may cause chain breakage and/or
kickback.
• Follow the manufacturer’s sharpen-
ing and maintenance instructions for
the saw chain. Decreasing the depth
gauge height can lead to increased
kickback.
13. Before starting work, check that the
chain saw is in proper working order
and that its condition complies with the
safety regulations. Check in particular
that:
• The chain brake is working properly;
• The run-down brake is working
properly;
• The bar and the sprocket cover are
tted correctly;
• The chain has been sharpened and
tensioned in accordance with the
regulations.
14. Do not start the chain saw with the
chain cover being installed on it. Starting
the chain saw with the chain cover being
installed on it may cause the chain cover
to thrown out forward resulting in personal
injury and damage to objects around the
operator.
Additional Safety Warnings:
1.
When using the tool with battery adapter, be
careful not to trip over the cord during operation.
2. When using the tool with battery adapter,
keep the cord away from obstacles such
as a workpiece and branches during
operation. The cord caught by obstacles
may cause serious injury.
Top handle chainsaw specic safety
warnings
1. Perform cleaning and maintenance
before storage in accordance with the
instruction manual.
2.
Ensure safe positioning of the chain saw during
car transportation to avoid fuel or chain oil
leakage, damage to the tool and personal injury.
3. Regularly check the functionality of
chain brake.
4. Do not ll the chain oil near re. Never
smoke when you ll the chain oil.
5. National regulation may restrict the use
of the chain saw.
6.
If the equipment gets heavy impact or
fall, check the condition before continu-
ing work. Check the controls and safety
devices for malfunction. If there is any
damage or doubt, ask our authorized ser-
vice center for the inspection and repair.
7. Always activate the chain brake before
starting the chain saw.
8. Hold the saw rmly in place to avoid
skating (skid movement) or bouncing of
the saw when starting a cut.
9. At the end of the cut, be careful to keep
your balance due to the “drop”.
10.
Take into account the direction and speed of
the wind. Avoid sawdust and chain oil mist.
Protective equipment
1.
In order to avoid head, eye, hand or foot
injuries as well as to protect your hearing
the following protective equipment must be
used during operation of the chain saw:
— The kind of clothing should be appro-
priate, i. e. it should be tight-tting
but not be a hindrance. Do not wear
jewelry or clothing which could become
entangled with bushes or shrubs. If you
have long hair, always wear a hairnet!
— It is necessary to wear a protective
helmet whenever working with the
chain saw. The protective helmet is
to be checked in regular intervals for
damage and is to be replaced after 5
years at the latest. Use only approved
protective helmets.

7ENGLISH
— The face shield of the protective hel-
met (or the goggles) protects against
sawdust and wood chips. During oper-
ation of the chain saw always wear a
goggle or a face shield to prevent eye
injuries.
— Wear adequate noise protection
equipment (ear mus, ear plugs, etc.)
— The protective jacket consists of 22
layers of nylon and protects the opera-
tor against cuts. It is always to be worn
when working from elevated platforms
(cherry pickers, lifts), from platforms
mounted on ladders or when climbing
with ropes.
— The protective brace and bib overall
is made of a nylon fabric with 22 layers
and protects against cuts. We strongly
recommend its use.
— Protective gloves made of thick
leather are part of the prescribed
equipment and must always be worn
during operation of the chain saw.
— During operation of the chain saw
safety shoes or safety boots tted
with anti skid sole, steel toe caps and
protection for the leg must always to
be worn. Safety shoes equipped with
a protective layer provide protection
against cuts and ensure a secure
footing. For working in trees the safety
boots must be suitable for climbing
techniques.
Vibration
1. Individuals with poor circulation who are
exposed to excessive vibration may experi-
ence injury to blood vessels or the nervous
system. Vibration may cause the following
symptoms to occur in the ngers, hands or
wrists: “Falling asleep” (numbness), tingling,
pain, stabbing sensation, alteration of skin
colour or of the skin. If any of these symp-
toms occur, see a physician! To reduce
the risk of “white nger disease”, keep your
hands warm during operation and well
maintain the equipment and accessories.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or famil-
iarity with product (gained from repeated
use) replace strict adherence to safety
rules for the subject product. MISUSE or
failure to follow the safety rules stated in
this instruction manual may cause serious
personal injury.
Symbols
The followings show the symbols used for tool.
volts
direct current
meter per second
feet per minute
parts number of applicable saw
chain and guide bar
Wear a helmet, goggles and ear
protection.
Use appropriate protection for
foot-leg and hand-arm.
Do not expose to moisture.
Always use two hands when
operating the chain saw.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all
instructions and cautionary markings
on (1) battery charger, (2) battery, and (3)
product using battery.
2. Do not disassemble or tamper with the
battery cartridge. It may result in a re,
excessive heat, or explosion.
3. If operating time has become exces-
sively shorter, stop operating imme-
diately. It may result in a risk of over-
heating, possible burns and even an
explosion.
4. If electrolyte gets into your eyes, rinse
them out with clear water and seek med-
ical attention right away. It may result in
loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects
such as nails, coins, etc.
(3) Do not expose battery cartridge to
water or rain.
A battery short can cause a large current
ow, overheating, possible burns and
even a breakdown.

8ENGLISH
6. Do not store and use the tool and battery
cartridge in locations where the tempera-
ture may reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge
even if it is severely damaged or is com-
pletely worn out. The battery cartridge
can explode in a re.
8. Do not nail, cut, crush, throw, drop the
battery cartridge, or hit against a hard
object to the battery cartridge. Such con-
duct may result in a re, excessive heat, or
explosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries
are subject to the Dangerous Goods
Legislation requirements.
For commercial transports e.g. by third
parties, forwarding agents, special require-
ment on packaging and labeling must be
observed.
For preparation of the item being shipped,
consulting an expert for hazardous material
is required. Please also observe possibly
more detailed national regulations.
Tape or mask o open contacts and pack up
the battery in such a manner that it cannot
move around in the packaging.
11. When disposing the battery cartridge,
remove it from the tool and dispose of it
in a safe place. Follow your local regula-
tions relating to disposal of battery.
12. Use the batteries only with the products
specied by Makita. Installing the batteries
to non-compliant products may result in a
re, excessive heat, explosion, or leak of
electrolyte.
13. If the tool is not used for a long period of
time, the battery must be removed from
the tool.
14. During and after use, the battery car-
tridge may take on heat which can cause
burns or low temperature burns. Pay
attention to the handling of hot battery
cartridges.
15. Do not touch the terminal of the tool
immediately after use as it may get hot
enough to cause burns.
16. Do not allow chips, dust, or soil stuck
into the terminals, holes, and grooves
of the battery cartridge. It may cause
heating, catching re, burst and malfunction
of the tool or battery cartridge, resulting in
burns or personal injury.
17. Unless the tool supports the use near
high-voltage electrical power lines,
do not use the battery cartridge near
high-voltage electrical power lines. It
may result in a malfunction or breakdown of
the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita bat-
teries. Use of non-genuine Makita batteries,
or batteries that have been altered, may result
in the battery bursting causing res, personal
injury and damage. It will also void the Makita
warranty for the Makita tool and charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before
completely discharged. Always stop tool
operation and charge the battery car-
tridge when you notice less tool power.
2. Never recharge a fully charged battery
cartridge. Overcharging shortens the
battery service life.
3. Charge the battery cartridge with room
temperature at 10 °C - 40 °C (50 °F - 104
°F). Let a hot battery cartridge cool down
before charging it.
4. When not using the battery cartridge,
remove it from the tool or the charger.
5. Charge the battery cartridge if you do
not use it for a long period (more than
six months).

9ENGLISH
PARTS DESCRIPTION
12 34
5
6
12
13
14
7
8
10
9
11
16
17
18
15
Fig.2
1Switch trigger 2Top handle 3Lock-o lever
4Front hand guard 5Guide bar 6Saw chain
7Chain catcher 8Retaining nut 9Chain adjusting screw
10 Chip guide 11 Battery cartridge 12 Main power lamp
13 Main power switch 14
Adjusting screw (for oil pump)
15 Carabiner
16 Front handle 17 Oil tank cap 18 Guide bar cover

10 ENGLISH
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool
is switched o and the battery cartridge is
removed before adjusting or checking func-
tion on the tool.
Installing or removing battery
cartridge
CAUTION: Always switch o the tool
before installing or removing of the battery
cartridge.
CAUTION: Hold the tool and the battery
cartridge rmly when installing or removing
battery cartridge. Failure to hold the tool and
the battery cartridge rmly may cause them to
slip o your hands and result in damage to the
tool and battery cartridge and a personal injury.
1
2
3
Fig.3
► 1. Red indicator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the
tool while sliding the button on the front of the
cartridge.
To install the battery cartridge, align the tongue
on the battery cartridge with the groove in the
housing and slip it into place. Insert it all the way
until it locks in place with a little click. If you can
see the red indicator as shown in the gure, it is
not locked completely.
CAUTION: Always install the battery
cartridge fully until the red indicator cannot
be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone
around you.
CAUTION: Do not install the battery car-
tridge forcibly. If the cartridge does not slide
in easily, it is not being inserted correctly.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
1
2
Fig.4
► 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge
to indicate the remaining battery capacity. The
indicator lamps light up for a few seconds.
Indicator lamps Remain-
ing
capacity
Lighted O Blinking
75% to
100%
50% to
75%
25% to
50%
0% to
25%
Charge
the
battery.
The bat-
tery may
have
malfunc-
tioned.
NOTE: Depending on the conditions of use
and the ambient temperature, the indication
may dier slightly from the actual capacity.
NOTE: The rst (far left) indicator lamp will
blink when the battery protection system
works.

11 ENGLISH
Tool / battery protection system
The tool is equipped with a tool/battery protec-
tion system. This system automatically cuts o
power to the motor to extend tool and battery life.
The tool will automatically stop during operation
if the tool or battery is placed under one of the
following conditions:
Overload protection
When the battery is operated in a manner that
causes it to draw an abnormally high current,
the tool automatically stops and the main power
lamp blinks in green. In this situation, turn the
tool o and stop the application that caused the
tool to become overloaded. Then turn the tool on
to restart.
Overheat protection
When the tool or battery is overheated, the tool
stops automatically and the main power lamp
lights up in red. In this case, let the tool and bat-
tery cool before turning the tool on again.
NOTE: In high temperature environment, the
overheat protection likely to work and the tool
stops automatically.
Overdischarge protection
When the battery capacity is not enough, the tool
stops automatically and the main power lamp
blinks in red. In this case, remove the battery
from the tool and charge the battery.
Main power switch
WARNING: Always turn o the main
power switch when not in use.
To turn on the tool, press the main power switch
until the main power lamp lights up in green. To
turn o, press the main power switch again.
1
2
Fig.5
► 1. Main power lamp 2. Main power switch
NOTE: The main power lamp blinks in green if
the switch trigger is pulled under unoperatable
conditions. The lamp blinks in one of the fol-
lowing conditions.
• When you turn on the main power switch
while holding down the lock-o lever and
the switch trigger.
• When you pull the switch trigger while the
chain brake is applied.
• When you release the chain brake while
holding down the lock-o lever and pulling
the switch trigger.
NOTE: This tool employs the auto power-o
function. To avoid unintentional start up, the
main power switch will automatically shut
down when the switch trigger is not pulled for
a certain period after the main power switch is
turned on.
You can use the tool in the Torque Boost mode
for cutting thick branches or hard branches. To
use the tool in the Torque Boost mode, when the
tool is turned o, press the main power switch for
a few seconds until the main power lamp lights
up in yellow.
NOTE: You can use the tool in the Torque
Boost mode up to 60 seconds. Depending on
the usage conditions, this mode shifts to the
normal mode in less than 60 seconds.
NOTE: If the main power lamp blinks in yellow
when you press the main power switch for a
few seconds, the Torque Boost mode is not
available. In this case, follow the steps below.
• The Torque Boost mode is not available
right after the cutting operation. Wait for
more than 10 seconds, and then press the
main power switch again.
• If you use the Torque Boost mode several
times, the use of the Torque Boost mode
is restricted to protect the battery. If the
Torque Boost mode is not available after
waiting for more than 10 seconds, replace
the battery cartridge with a fully charged
one, or recharge the battery cartridge.
NOTE: If the main power lamp lights up in red
or blinks in red or green, refer to the instruc-
tions for tool/battery protection system.
NOTE: The Torque Boost mode cannot be
used when the battery cartridge BL1815N or
BL1820B is installed.

12 ENGLISH
Switch action
WARNING: For your safety, this tool is
equipped with lock-o lever which prevents
the tool from unintended starting. NEVER
use the tool if it runs when you simply
pull the switch trigger without pressing
the lock-o lever. Return the tool to our
authorized service center for proper repairs
BEFORE further usage.
WARNING: NEVER tape down or defeat
purpose and function of lock-o lever.
CAUTION: Before installing the battery
cartridge into the tool, always check to see
that the switch trigger actuates properly
and returns to the "OFF" position when
released.
NOTICE: Do not pull the switch trigger hard
without pressing the lock-o lever. This can
cause switch breakage.
To prevent the switch trigger from being acci-
dentally pulled, a lock-o lever is provided. To
start the tool, depress the lock-o lever and pull
the switch trigger. The tool speed increases
by increasing pressure on the switch trigger.
Release the switch trigger to stop.
1
2
Fig.6
► 1. Switch trigger 2. Lock-o lever
Checking the chain brake
CAUTION: Hold the chain saw with both
hands when switching it on. Hold the top
handle with your right hand, the front han-
dle with your left. The bar and the chain
must not be in contact with any object.
CAUTION: Should the saw chain not
stop immediately when this test is per-
formed, the saw may not be used under
any circumstances. Consult our authorized
service center.
1. Press the lock-o lever, then pull the switch
trigger. The saw chain starts immediately.
2. Push the front hand guard forwards with the
back of your hand. Make sure that the chain saw
comes to an immediate standstill.
1
23
23
Fig.7
► 1. Front hand guard 2. Unlocked position
3. Locked position
Checking the run-down brake
CAUTION: If the saw chain does not stop
within two seconds in this test, stop using
the chain saw and consult our authorized
service center.
Run the chain saw then release the switch trig-
ger completely. The saw chain must come to a
standstill within two seconds.

13 ENGLISH
Adjusting the chain lubrication
You can adjust the oil pump feed rate with the
adjusting screw using the universal wrench. The
amount of oil can be adjusted in 3 steps.
1
Fig.8
► 1. Adjusting screw
Carabiner (rope attachment point)
You can hang the tool by attaching the rope to
the carabiner. Pull up the carabiner, and then tie
it with the rope.
Electronic function
The tool is equipped with the electronic functions
for easy operation.
• Soft start
The soft-start function minimizes start-up
shock, and makes the tool start smoothly.
ASSEMBLY
CAUTION: Always be sure that the tool
is switched o and the battery cartridge is
removed before carrying out any work on
the tool.
CAUTION: Do not touch the saw chain
with bare hands. Always wear gloves when
handling the saw chain.
Removing or installing saw chain
CAUTION: The saw chain and the guide
bar are still hot just after the operation. Let
them cool down enough before carrying out
any work on the tool.
CAUTION: Carry out the procedure of
installing or removing saw chain in a clean
place free from sawdust and the like.
To install the saw chain, perform the following
steps:
1. Check the direction of the saw chain. Match
the direction of the saw chain with that of the
mark on the chain saw body.
2. Fit one end of the saw chain on the top of
the guide bar.
3. Fit the other end of the saw chain around
the sprocket, then attach the guide bar to the
chain saw body, aligning the hole on the guide
bar with the pin on the chain saw body.
1
2
Fig.9
► 1. Sprocket 2. Hole
4. Insert the protrusion on the sprocket cover
to the chain saw body, and then close the cover
so that the bolt and pins on the chain saw body
meet their counterparts on the cover.
2
3
4
1
Fig.10
► 1. Protrusion 2. Sprocket cover 3. Bolt 4. Pin

14 ENGLISH
5. Tighten the retaining nut to secure the
sprocket cover, then loosen it a bit for tension
adjustment.
(See the chapter on "Adjusting saw chain ten-
sion" for procedure.)
1
Fig.11
► 1. Retaining nut
To remove the saw chain, perform the following
steps:
1. Release the chain brake by pulling the front
hand guard.
2. Loosen the chain adjusting screw, then the
retaining nut.
1
2
Fig.12
► 1. Chain adjusting screw 2. Retaining nut
3. Remove the sprocket cover then remove
the saw chain and guide bar from the chain saw
body.
Adjusting saw chain tension
CAUTION: Do not tighten the saw chain
too much. Excessively high tension of saw
chain may cause breakage of saw chain and
wear of the guide bar.
CAUTION: A chain which is too loose
can jump o the bar and it may cause an
injury accident.
The saw chain may become loose after many
hours of use. From time to time check the saw
chain tension before use.
1. Release the chain brake by pulling the front
hand guard.
2. Loosen the retaining nut a bit to loosen the
sprocket cover lightly.
1
Fig.13
► 1. Retaining nut
3. Lift up the guide bar tip slightly and adjust
the chain tension. Turn the chain adjusting screw
clockwise to tighten, turn it counterclockwise
to loosen. Tighten the saw chain until the lower
side of the saw chain ts in the guide bar rail as
illustrated.
1
2
3
Fig.14
► 1. Guide bar 2. Saw chain 3. Chain adjusting
screw

15 ENGLISH
4. Keep holding the guide bar lightly and
tighten the sprocket cover. Make sure that the
saw chain does not loose at the lower side.
5. Tighten the retaining nut to secure the
sprocket cover.
1
Fig.15
► 1. Retaining nut
Make sure the saw chain ts snugly against the
lower side of the bar.
Spike bumper
Optional accessory
When cutting thick branches, using the spike
bumper is recommended. To install the spike
bumper, perform the following steps:
1. Remove the sprocket cover, saw chain, and
guide bar.
2. Align the holes of the spike bumper with the
holes on the chain saw body, and then tighten
the screws rmly.
12
Fig.16
► 1. Screw 2. Spike bumper
OPERATION
Lubrication
Saw chain is automatically lubricated when the
tool is in operation. Check the amount of remain-
ing oil in the oil tank periodically through the oil
inspection window.
To rell the tank, lay the chain saw on its side
and remove the oil tank cap. The proper amount
of oil is 140 ml. After relling the tank, make sure
that the oil tank cap is tightened securely.
1
2
Fig.17
► 1. Oil tank cap 2. Oil inspection window
After relling, hold the chain saw away from the tree. Start
it and wait until lubrication on saw chain is adequate.
Fig.18
NOTICE: When lling the chain oil for the
rst time, or relling the tank after it has
been completely emptied, add oil up to the
bottom edge of the ller neck. The oil deliv-
ery may otherwise be impaired.
NOTICE: Use the saw chain oil exclusively
for Makita chain saws or equivalent oil
available in the market.
NOTICE: Never use oil including dust and
particles or volatile oil.
NOTICE: When pruning trees, use botanical
oil. Mineral oil may harm trees.
NOTICE:
Before the cutting operation, make sure
that the provided oil tank cap is screwed in place.

16 ENGLISH
WORKING WITH THE CHAIN SAW
CAUTION: The rst time user should, as
a minimum practice, do cutting logs on a
saw-horse or cradle.
CAUTION: When sawing precut timber,
use a safe support (saw horse or cradle).
Do not steady the workpiece with your foot,
and do not allow anyone else to hold or
steady it.
CAUTION: Secure round pieces against
rotation.
CAUTION: Keep all parts of the body
away from the saw chain when the motor is
operating.
CAUTION: Hold the chain saw rmly with
both hands when the motor is running.
CAUTION: Do not overreach. Keep
proper footing and balance at all times.
NOTICE: Never toss or drop the tool.
NOTICE: Do not cover the vents of the tool.
Pruning trees
Bring the chain saw body into contact with the
branch to be cut before switching on. Otherwise
it may cause the guide bar to wobble, resulting
in injury to operator. Saw the wood to be cut by
just moving it down by using the weight of the
chain saw.
Fig.19
If you cannot cut the timber right through with a
single stroke:
Apply light pressure to the handle and continue
sawing and draw the chain saw back a little.
Fig.20
When cutting thick branches, rst make a shal-
low undercut and then make the nish cut from
the top.
1
2
Fig.21
If you try to cut o thick branches from the
bottom, the branch may close in and pinch the
saw chain in the cut. If you try to cut o thick
branches from the top without a shallow under-
cut, the branch may splinter.
Fig.22

17 ENGLISH
Limbing
CAUTION: Limbing may only be per-
formed by trained persons. A hazard is pre-
sented by the risk of kickback.
When limbing, support the chain saw on the
trunk if possible. Do not cut with the tip of the
bar, as this presents a risk of kickback.
Pay particular attention to branches under ten-
sion. Do not cut unsupported branches from
below.
Do not stand on the felled trunk when limbing.
Carrying tool
Before carrying the tool, always apply the chain
brake and remove the battery cartridges from the
tool. Then attach the guide bar cover. Also cover
the battery cartridge with the battery cover.
1
2
Fig.23
► 1. Guide bar cover 2. Battery cover
MAINTENANCE
CAUTION: Always be sure that the tool
is switched o and the battery cartridge
is removed before attempting to perform
inspection or maintenance.
CAUTION: Always wear gloves when
performing any inspection or maintenance.
NOTICE: Never use gasoline, benzine,
thinner, alcohol or the like. Discoloration,
deformation or cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment
should be performed by Makita Authorized or
Factory Service Centers, always using Makita
replacement parts.
Sharpening the saw chain
Sharpen the saw chain when:
• Mealy sawdust is produced when damp
wood is cut;
• The chain penetrates the wood with di-
culty, even when heavy pressure is applied;
• The cutting edge is obviously damaged;
• The saw pulls to the left or right in the wood.
(caused by uneven sharpening of the saw
chain or damage to one side only)
Sharpen the saw chain frequently but a little
each time. Two or three strokes with a le are
usually sucient for routine resharpening. When
the saw chain has been resharpened several
times, have it sharpened in our authorized ser-
vice center.
Sharpening criteria:
WARNING: An excessive distance
between the cutting edge and depth gauge
increases the risk of kickback.
22
11
31
Fig.24
► 1. Cutter length 2. Distance between cutting
edge and depth gauge 3. Minimum cutter
length (3 mm (1/8"))
— All cutter length must be equal. Dierent
cutter lengths prevent the saw chain from
running smoothly and may cause the saw
chain to break.
— Do not sharpen the chain when the cutter
length has reached 3 mm (1/8") or shorter.
The chain must be replaced with new one.
— The chip thickness is determined by the
distance between the depth gauge (round
nose) and the cutting edge.
— The best cutting results are obtained with
following distance between cutting edge
and depth gauge.
• Chain blade 90PX : 0.65 mm (0.025″)
Chain blade 80TXL : 0.65 mm (0.025″)

18 ENGLISH
30
30
55 55
Fig.25
— The sharpening angle of 30° must be
the same on all cutters. Dierent cutter
angles cause the chain to run roughly and
unevenly, accelerate wear, and lead to
chain breaks.
— Use a suitable round le so that the proper
sharpening angle is kept against the teeth.
• Chain blade 90PX : 55°
Chain blade 80TXL : 55°
File and le guiding
— Use a special round le (optional accessory)
for saw chains to sharpen the chain. Normal
round les are not suitable.
— Diameter of the round le for each saw
chain is as follows:
• Chain blade 90PX : 4.5 mm (3/16″)
Chain blade 80TXL : 4.0 mm (5/32″)
— The le should only engage the cutter on
the forward stroke. Lift the le o the cutter
on the return stroke.
— Sharpen the shortest cutter rst. Then the
length of this shortest cutter becomes the
standard for all other cutters on the saw
chain.
— Guide the le as shown in the gure.
1
2
Fig.26
► 1. File 2. Saw chain
—
The le can be guided more easily if a le holder
(optional accessory) is employed. The le holder has
markings for the correct sharpening angle of 30° (align
the markings parallel to the saw chain) and limits the
depth of penetration (to 4/5 of the le diameter).
30
1/5
1
Fig.27
► 1. File holder
— After sharpening the chain, check the height
of the depth gauge using the chain gauge
tool (optional accessory).
Fig.28
—
Remove any projecting material, however small,
with a special at le (optional accessory).
—
Round o the front of the depth gauge again.
Cleaning the guide bar
Chips and sawdust will build up in the guide bar
groove. They may clog the bar groove and impair
the oil ow. Clean out the chips and sawdust every
time when you sharpen or replace the saw chain.
Fig.29

19 ENGLISH
Cleaning the sprocket cover
Chips and saw dust will accumulate inside of the
sprocket cover. Remove the sprocket cover and
saw chain from the tool then clean the chips and
saw dust.
Fig.30
Cleaning the oil discharge hole
Small dust or particles may be built up in the oil
discharge hole during operation. These dust or
particles may impair the oil to ow and cause an
insucient lubrication on the whole saw chain.
When a poor chain oil delivery occurs at the
top of guide bar, clean the oil discharge hole as
follows.
1. Remove the sprocket cover and saw chain
from the tool.
2. Remove the small dust or particles using a
slotted screwdriver or the like.
1
2
Fig.31
► 1. Slotted screwdriver 2. Oil discharge hole
3. Insert the battery cartridge into the tool. Pull
the switch trigger to ow built-up dust or particles
o the oil discharge hole by discharging chain
oil.
4. Remove the battery cartridge from the tool.
Reinstall the sprocket cover and saw chain on
the tool.
Replacing the sprocket
CAUTION: A worn sprocket will dam-
age a new saw chain. Have the sprocket
replaced in this case.
Before tting a new saw chain, check the condi-
tion of the sprocket.
1
2
Fig.32
► 1. Sprocket 2. Areas to be worn out
Always t a new locking ring when replacing the
sprocket.
1
2
Fig.33
► 1. Locking ring 2. Sprocket
NOTICE: Make sure that the sprocket is
installed as shown in the gure.
Storing the tool
1. Clean the tool before storing. Remove any
chips and sawdust from the tool after removing
the sprocket cover.
2. After cleaning the tool, run it under no load
to lubricate the saw chain and guide bar.
3. Cover the guide bar with the guide bar
cover.
4. Empty the oil tank.

20 ENGLISH
Instructions for periodic maintenance
To ensure long life, prevent damage and ensure the full functioning of the safety features, the follow-
ing maintenance must be performed regularly. Warranty claims can be recognized only if this work
is performed regularly and properly. Failure to perform the prescribed maintenance work can lead to
accidents! The user of the chain saw must not perform maintenance work which is not described in the
instruction manual. All such work must be carried out by our authorized service center.
Check item / Operating
time
Before
operation
Everyday Every
week
Every 3
month
Annually Before
storage
Chain saw Inspection. -----
Cleaning. -----
Check at
authorized
service
center.
----
Saw chain Inspection. -----
Sharp-
ening if
necessary.
-----
Guide bar Inspection. ----
Remove
from the
chain saw.
-----
Chain
brake
Check the
function.
-----
Have it
inspected
regularly at
authorized
service
center.
--- - -
Chain
lubrication
Check the
oil feed
rate.
-----
Switch
trigger
Inspection. -----
Lock-o
lever
Inspection. -----
Oil tank
cap
Check
tightness.
-----
Chain
catcher
Inspection. - - ---
Screws
and nuts
Inspection. - - ---
This manual suits for next models
2
Table of contents
Languages:
Other Makita Chainsaw manuals

Makita
Makita EA3600F User guide

Makita
Makita UC3041A User manual

Makita
Makita DUC254 User manual

Makita
Makita EA6100P User manual

Makita
Makita EA3500S User manual

Makita
Makita UC016G User manual

Makita
Makita EA3600F User guide

Makita
Makita DCS510 Instruction Manual

Makita
Makita EA3500SRDB Instruction Manual

Makita
Makita BUC250 User manual

Makita
Makita DUC256 User manual

Makita
Makita UC003G User manual

Makita
Makita EA3500S User manual

Makita
Makita DUC307 User manual

Makita
Makita BUC121 User manual

Makita
Makita DUC353ZB User manual

Makita
Makita BUC121 User manual

Makita
Makita 5014B Manual

Makita
Makita 5014B User manual

Makita
Makita 5014B User manual