Makita 601D User manual

Battery-Powered Driver Drill
Steel / Wood
10mm
(318")
Equipped with Electric Brake
10 mm (3/8") MODEL 601D
10 mm (3/8") MODEL 6OlDST
With Battery & Charger
Wood screw (RPM) (L x W x H) weight
0.7 kg
(311
6" x 3/4"1 - 750 (7-13116" x 1-13/16" x 6-5/32") (1.5 lbs)
4.5 mm x 20 mm 198 mm x 46 mm x 156 mm
INSTRUCTION MANUAL
Battery 122
Voltage
12v
SPECIFICATIONS
Model DC122 Charger Charging time
A.C. 115V
6OHz D.C. 12V Approx. 1 Hr.
Input output
Model 601D
Capacities 1 No load speed I Dimensions Net
Note: Specifications may differ from country to country.
Makita battery 122
is a lead-acidbattery. Be sure to follow the following instructions tocharge it.
1)Always charge
it immediately after purchase.
A 2) Always recharge it after use.
[ 0 \ 31 Be sure tocharge it for approx. one week every six months, when not using it for long periods.
CAUTION If left uncharged, it may become unchargeable.
WARNING:
Read the important safety instructions
For your personal safety, READ and UNDERSTAND before using.
Use only the Makita battery 121 or 122.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

IMPORTANT
SAFETY INSTRUCTIONS
(For All Tools)
WARNING:
WHENUSINGELECTRICTOOLS, BASIC SAFETY
PRECAUTIONSSHOULDALWAYS BE FOLLOWEDTO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
2
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools
in damp
or wet locations. Keep work area well
lit. Don't expose power tools to rain.
Don't use tool in presence of flammable liquids or gases.
KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don't let visitors contact tool or extension cord.
STORE IDLETOOLS. When not
in use, tools should bestored in dry, and high
or locked-up place - out of reach of children.
DON'T FORCE TOOL.
It will dothejob better and safer atthe ratefor which
it was intended.
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a
heavy-dutytool. Don't use toolfor purpose notintended; for example, don't
use circular saw for cutting tree limbs or logs.
DRESS PROPERLY. Don't wear loose clothing orjewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to containlonghair.
USE SAFETY GLASSES. Also use face or dust mask
if cutting operation is
dusty.
DON'T ABUSE CORD. Nevercarry toolby cord or yank
it todisconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
it frees both hands to operate tool.
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing acces-
sories. Inspecttool cords periodicallyand
if damaged, haverepaired by autho-
rized service facility. Inspect extension cords periodically and replace
if
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECTTOOLS. When not
in use, beforeservicing, andwhen chang-
ing accessories, such as blades, bits, cutters.

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from toolbeforeturning
it on.
15. AVOID UNINTENTIONALSTARTING. Don’t carry tool
with finger onswitch.
Be sure switch is OFF when plugging
in.
16. OUTDOOR USEEXTENSIONCORDS. When tool is usedoutdoors, use only
extension cords intended for use outdoors and
so marked.
17. STAY ALERT. Watch what you are doing, use common sense. Don’t operate
tool when you are tired.
18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that
it will
operate properly and perform its intended function. Check for alignment of
moving parts, bindingof moving parts, breakageof parts, mounting, and any
other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized serv-
ice center unless otherwise indicated elsewhere inthis instruction manual.
Have defective switches replaced by authorized service center. Don’t use
tool
if switch does not turn it on and off.
19. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20. REPLACEMENT PARTS. When servicing, useonly identicalreplacementparts.
21, POLARIZEDPLUGS. To reduce the risk of electric shock, this equipment has
a polarized plug (one blade is wider than the other). This plug
will fit in a
polarized outlet only one way. If the plug does not
fit fully in the outlet,
reversethe plug.
If it stilldoes not fit, contacta qualified electriciantoinstall
the proper outlet.
Do not change the plug in any way.
VOLTAGE WARNING: Before connecting the toolto a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user
- as well as damage to
the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with
voltage less than the nameplate rating is harmful to the motor.
3

IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY
& CHARGER
Length of Cord (Feet) 25
AWG Size of Cord 18
I. SAVE THESE INSTRUCTIONS - This manual
50 100 150
18 18 16
9. Do not operate charger with damaged cord or plug - replace them im-
mediately.
IO. Do not operate charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way; take
it to a qualified serviceman.
11. Donotdisassemblecharger or battery; take it toa qualified serviceman when
service or repair is required. Incorrect reassembly may result
in a risk of
electric shock or fire.
12. To reduce risk of electric shock, unplug charger from outlet beforeattempt-
ingany maintenance or cleaning.Turning
off controls will notreducethis risk.
4

ADDITIONAL SAFETY RULES FOR BATTERY
1. Always charge the Makita battery 122 immediately after purchase.
2. Always recharge the Makita battery 122 after use.
3. Be sure to charge the Makita battery 122 for approx. one week every six
months, when notusing
it for longperiods. Ifleftuncharged, it may become
unchargeable.
4. Use only the Makita charger Model DC122 or DC121 specified to charge
the Makita battery
122.
5. Do not charge inside a box or container of any kind.
6. Do not short the battery:
1) Do not touch the terminals with any conductive material.
2) Avoidstoringbattery
in a container with other metalobjects suchas nails,
3) Do not expose battery to water or rain.
4) Do not cut the adaptor cord.
A battery short can cause a large current flow, overheating, possible burns
and even a breakdown.
7. Do not leave the battery exposed todirect sunlight. Do notstorethe battery
in locations where the temperature may reach or exceed 4OoC (104OF).
8. The Makita battery 122contains a strong electrolyte (dilute sulfuric acid).
Do not apply undue force to the battery, drop or strike
it. Do not attempt
to disassemble or make modifications to the battery.
9. If the battery breaks open andelectrolyte (dilutesulfuric acid)contacts skin
or clothing, wash immediately
with running water. If electrolyte gets into
your eyes, rinsethem out
with clear water and seek medicalattention right
away.
IO. As the battery service life ends, itscapacity and operation time decrease.
Replace
it with a new one.
11. Never expose the battery toflames, fire or great heat. Breakage may cause
release
of injurious material.
coins, etc.
5

ADDITIONAL SAFETY RULES FOR CHARGER
1. The Makita charger Model DC122 is specifically designed to charge only
the Makita battery 121 or
122. Do not attempt tocharge any other battery
with this charger.
2. Handle the charger carefully. Do not drop or strike it.
3. Never carry the charger by cord or yank it to disconnect from receptacle.
4. Keep cord from heat, oil, chemicals, and sharp edges.
5. Useonly a powersource of the same voltage as indicated onthe nameplate
6. Do not attempt to use a step-up transformer, an engine generator or DC
7. Charge the battery at a room temperature of 10°C (5OOF)
- 4OoC (104OF).
8. Do not charge in place exposed to direct sunlight.
9. Do not allow the charger to get wet.
IO. Do not charge inside a box or container of any kind.
11. Donot charge near volatile, flammable material such as gasoline, paint, gas,
12. Do not charge on top of paper, carpet, vinyl sheeting, cloth materials, etc.
13. Do not allow anything to cover or clog the charger vents. Do not attempt
14. Do not charge in dusty place.
15. Stop charging immediately
if you notice anything abnormal. Ship or take the
charger and the battery toyour nearest Makita Service Center or Distributor
for checking them.
of the charger when charging.
power receptacle.
adhesive, etc.
to insert anything into the vents.
16. Do not attempt to disassemble or make modifications to the charger.
17. Do not put any metalobjects or foreign matter intothe inlet of the charger.
Short-circuit will occur, causing a burn injury and charger breakdown.
6

ADDITIONAL SAFETY RULES FOR TOOL
1. This tool is specifically designed to drill in woods/metals or to drive wood
2. Always be sure you have a firm footing.
3. Always secure small workpieces in a vise or similar hold-down device.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. When drilling into walls, floors or wherever "live" electric wires may be
encountered,
DO NOT TOUCH ANY METAL PARTS OF THE TOOL!
Holdthe tool only by the insulatedgrasping surfaces toprevent electric shock
if you drill into a "live" wire.
screws.
Do not use it for other purposes.
Be sure no one is below when using the tool
in high locations.
7. Do not leave the tool running. Operate the tool only when hand-held.
8. Do not touch the drill bit or the workpiece immediately after operation; they
may be extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.

Charging
Connect the battery tothe charger using the adaptor cord. Then plugthe charger into the
power source. The charging light will illuminate and charging will begin. When the charg-
ing light goes out
at a certain time, the charging is complete. Unplugthecharger.
(Note: Refer to the table belowfor the charging time.)
DC122 DC121
122
3
\
Approx. 1 hour Approx. 2 hours
Outlet
Furcord
7
121
Charger
rCharging,light -Connector
ADDrox.
2 hours ADDrox. 4 hours
CAUTION :
0 Always chargethe Makita battery 122immediately after purchase.
*Always recharge the Makita battery 122after use.
If the Makita battery 122 has not been used for longperiods, charge
it for more than the
time specifiedinthe table above. (Example: If
it has not been used for six months, charge
it for approx. one week.) Charging continues even after the charging light goes out. Ifthe
battery
is left uncharged for more than six months, it may become unchargeable. Ifthe
light does not come on within five minutes after you start the charging, the battery may
be unchargeable. Ship or take the charger and the battery to your nearest Makita Service
Center or Distributor for checking.
8

Installingor removing the drillbit
CAUTION
:
Always be sure that the tool is switched off and the batterv is disconnectedfrom the tool
before installingor removingthe bit.
To install the bit, place it in the chuck as
far as it will go. Tighten the chuck by hand.
Place the chuck key in each
of the three
holes and tighten clockwise. Be
sure to
tighten all three chuck holes evenly.
To remove the bit, turn the chuck key
counterclockwise in just one hole, then
loosenthe chuck by hand.
After usingthe chuck key, be sure to return
it to the original position
Switch action
To start the tool, simply pull the trigger. Tool speed is increased by increasingpressure on
the trigger.
Release the trigger to stop.
CAUTION
:
Before connecting the battery to the tool, always check to see that the switch trigger
actuatesproperly and returns to the
"OFF" positionwhen released.
Reversing switch action
This tool has
a reversing switch to change
the direction of rotation. Move the revers-
ing switch lever to the right for clockwise
rotation or to the left for counterclockwise
rotation.
Aeversing switch lever
/
CAUTION :
Always check the direction of rotation before operation.
*The reversingswitch lever cannot be moved while the trigger
is pulled.
Use the reversing switch only after the tool comes to complete stop. Changing the
direction of rotationbefore the tool stops may damage the tool.
9

Connectingthe battery to the tool
Connect the battery to the tool usingthe adaptor cord. To prevent the adaptor cord from
being accidentally disconnected, hook the cord to the strain relief hook on the battery.
Carryingthe battery
Hook the battery to your waist belt. Ifthe
adaptor cord
is too longfor your work, use
the band providedtohold
it when you coil
it shorter.
I
. cord
-Band
Drillingoperation
0 Drillinginwood
When drilling in wood, best results are obtainedwith wood drills equippedwith
a guide
screw, The guide screw makes drilling easier by pulling the bit into the workpiece.
0 Drillingin metal
To preventthe bit from slippingwhen starting
a hole, make an indentation with a center-
punch and hammer
at the point to be drilled. Place the point of the bit inthe indenta-
tion and start drilling.
Use a cutting lubricant when drilling metals. The exceptions are
ironand brass which should be drilled dry.
CAUTION
:
0 Pressingexcessively on the tool will not speed up the drilling. Infact, this excessive pres-
sure will only serve to damage the tip of your bit, decrease the tool performance and
shortenthe service life
of the tool.
.There
is a tremendous force exerted on the tool/bit at the time of hole breakthrough.
Hold the tool firmly and exertcare when the bit beginsto break through the workpiece.
0 A stuck bit can be removed simply by settingthe reversing switchto reverse rotationin
orderto back out. However,the tool may back out abruptly if you do not hold
it firmly.
Always secure small workpieces in a vise or similar hold-downdevice.
10