Makita 6300D User manual

n
Dimensions
(LxWxH1
Capacities
No load speed IRPM)
Steel Wood Wood screw High LOW
I
@@
Net
weight
Equipped with Electric Brake
13 mm (1/2") MODEL 6300D
13 mm (1/2") MODEL 6300DW
With Fast Charger
13"
1112")
INSTRUCTION MANUAL
21 mm 58mmx75mm 225 mm x 58 mm x 272 mm 2.6 kg
113116"l (15164"
x 2-15/16") - l"oo ~ 450 18.718'' x 2-5/16'' x 10-11/16") (5.7 Ibs)
10.8 v
1 Hr. A C only 50 Hz ~ 60 Hr D.C. 10.8 V
output
Voltage
I Charging time I Input I

IMPORTANT
SAFETY INSTRUCTIONS
(For All Tools)
WARNING:
WHEN USING ELECTRICTOOLS, BASIC SAFETY
PRECAUTIONSSHOULD ALWAYS
BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1.
2.
3.
4.
5.
6.
7.
8.
9.
IO.
11.
12.
13.
2
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp
or wet locations. Keep work area well
lit. Don't expose power tools to rain.
Don't use tool in presence of flammable liquids or gases.
KEEP CHILDREN AWAY.
All visitors should be kept away from work area.
Don't let visitors contact tool
or extension cord.
STORE IDLETOOLS. When not
in use, tools should be storedindry, and high
or locked-up place - out of reach of children.
DON'T FORCE TOOL.
It will do thejob better and safer at the ratefor which
it was intended.
USE RIGHT TOOL. Don't force small tool or attachment to
do the job of a
heavy-duty tool. Don't use tool for purpose not intended.
DRESS PROPERLY. Don't wear loose clothingorjewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair coveringtocontain long hair.
USE SAFETY GLASSES. Also use face or dust mask
if cutting operation is
dusty.
DON'T ABUSE CORD. Never carry tool by cord or yank
it todisconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
it frees both hands to operate tool.
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricatingand changing acces-
sories. Inspect toolcords periodically and
if damaged, haverepairedbyautho-
rized service facility. Inspect extension cords periodically and replace
if
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECTTOOLS. When not inuse, before servicing, and when chang-
ing accessories, such as blades, bits, cutters.

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keysand adjusting wrenches are removed from tool before turning
it on.
15. AVOID UNINTENTIONALSTARTING. Don't carry plugged-intool withfinger
on switch. Be sure switch is
OFF when plugging in.
16. OUTDOOR USE EXTENSIONCORDS. Whentool is used outdoors, useonly
extension cords intended for use outdoors and so marked.
17. STAY ALERT. Watch what you are doing, use commonsense. Don't operate
tool when you are tired.
18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that
it will
operate properly and perform itsintended function. Check for alignment of
moving parts, binding of moving parts, breakage
of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction
manual. Have defective switches replacedby authorized service center. Don't
use tool if switch does not turn
it on and off.
19. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20. REPLACEMENT PARTS. When servicing, useonly identicalreplacementparts.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user
- as well as damage to
the tool. If in doubt, DO NOT PLUG
IN THE TOOL. Using a power source with
voltage less than the nameplate rating is harmful to the motor.
3

I M PO RTANT
Length of Cord (Feet)
AWG Size of Cord
SAFETY
25 50 100 150
18 18 18 16
INSTRUCTI 0 N S
1. SAVE THESE INSTRUCTIONS - This manual
contains important safety and operating instructions for battery charger.
2. Before using battery charger, read all instructions and cautionary markings
on (1 1 battery charger, (2) battery, and (3) product using battery.
3. CAUTION - To reduce risk of injury, charge only MAKITA Battery 7000.
Other types of batteries may burst causing personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by the battery charger
manufacturermay result
in a riskof fire, electric shock, or injurytopersons.
6. To reduce risk of damage toelectric plug and cord, pull by plug rather than
cord when disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over,
or otherwise subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pinsonplugof extension cord are the same number, size, and shape
b. That extension cord isproperly wired and ingood electrical condition; and
c. That wire size is at least as large as the one specified inthe table below.
TABLE
1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
as those of plug on charger;
4

ADDITIONAL SAFETY RULES
FOR CHARGER
& BATTERY CARTRIDGE
1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF)
or ABOVE 4OoC(104OF).
2.
Do notattempt tousea step-up transformer, an enginegenerator or DC power
3. Do not allow anything to cover or clog the charger vents.
4. Do not short the battery cartridge:
receptacle.
(11 Do not touch the terminals with any conductive material.
(2) Avoid storing battery cartridge in a container with other metalobjects such
(3) Do not expose battery cartridge to water or rain.
as nails, coins, etc.
A batteryshort can cause a largecurrent flow, overheating, possible burns
and even a breakdown.
5. Do not store the tool and Battery Cartridge in locations where the tempera-
6. Do not incinerate the Battery Cartridge even if it is severely damaged or is
ture may reach or exceed
5OoC(122OF).
completely worn out. The battery cartridge can explode in a fire.
ADDITIONAL SAFETY RULES
1. Be aware that this tool is always in an operating condition, because it does
2. Always be sure you have a firm footing.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. When drilling into walls, floors or wherever "live" electrical wires may be
encountered,
DO NOT TOUCH ANY METAL PARTS OF THE TOOL!
Holdthe toolonly by the insulatedgrasping surfaces toprevent electric shock
if you drill into a "live" wire.
not have to be plugged into an electrical outlet.
Be sure no one is below when using the tool in high locations.
6. Do not leave the tool running. Operate the tool only when hand-held.
7. Do not touchthe drill bit or the workpiece immediately after operation: they
may be extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
5

Charging
Use the Fast Charger DC1000 to charge the
Battery Cartridge 1000.
To remove the battery cartridge, push up
the slide plate and grasp the cartridge care-
fully while withdrawing
it from the tool.
Plug the fast charger into your power
source. Insert the battery cartridge
so
that the plus and minus terminals on the
battery cartridge are on the same sides
as their respective markings on the fast
charger. Insert the cartridge fully into the
port
so that it rests on the charger port
floor. Check to
see that the charging light
comes on. When it goes out, you may re-
move the fully charged battery cartridge.
After charging, unplug the charger from
the power source.
To insert the battery cartridge, slide it all the way inside the tool. Then pull down the
slide plate to secure the battery cartridge.
CAUTION
:
0 Your new battery cartridge is notcharged. You will need to charge itbefore use.
0 If you try to charge a cartridge from a just-operated tool, sometimes the charginglight
will not come on. If this occurs,
let the cartridge cool off for a while. Then re-insert it
and try to charge
it once more.
When you charge a new battery cartridge or a battery cartridge which has not been used
for
a long period, it may not accept a full charge. This is a normal condition and does
not indicate a problem. You can recharge the battery cartridge fully after discharging it
almost completely a couple of times.
0 If youwish to charge two battery cartridges,allow 15 minutes between chargings on the
fast charger.
6

Nominal diameter of wood screw
Bit No.
2.1 - 2.7 (3/32" - 1/8")
Selecting bit
*Phillips bit
Use the chart to determine the best
size
driver bit for the size of screw that you
No. 2
No. 3
wish to use.
3.1 - 4.8 (118"- 3/16")
5.1
- 5.8 (13164'' - 15/64")
Slotted bit
Use
a slotted bit that properly fits the screw slot. Use of
a bit that is too small will
damage the screw and/or bit.
Installing or removing drill bitor driver bit
CAUTION:
Always be sure that the tool
is switched off and the battery cartridge is removed before
installing or removing the bit.
To install the bit, place
it in the chuck as
far as it will go. Tighten the chuck by hand.
Place the chuck key in each of the three
holes and tighten clockwise.
Be sure to
tighten all three chuck holes evenly.
To remove the bit, turn the chuck key
counterclockwise in just one hole, then
loosen the chuck byhand.
Chuck key
/
Chuck key
7

CAUTION :
Before inserting the battery cartridge into the tool, always check to see that the trigger
switch actuates properly and returns to the "OFF" position when released.
To change the speed, turn the speed change
knob
180" while the tool is running. Be
sure that the speed change knob
is turned
to the correct speed setting before you
Reversing switch action
This tool has a reversing switch to change
the direction of rotation. Slide the revers-
ing switch to the right for clockwise rota-
tionor to the left for counterclockwise.
Speed
change knob
450 R/min.
'q I-' 1,200 R/min.
1 /-
CAUTION :
0 Always check the directionof rotation before operation.
*Use the reversing switch only when the tool comes to
a complete stop. Changing the
directionof rotation before the tool stops may ruinthe tool.
Speed change k
begin operation. See arrow indication. Use
the rightspeed for the job.
8

Overload protector
The overload protector automatically cuts
out to break the circuit and the button
pops out, whenever heavy work is pro-
longed. When this occurs,release thetrigger
switch and withdraw the tool from the
workpiece. Wait
20 - 30 seconds before
pressing the restart button to resume
operation.
4.8(3/16")
CAUTION :
Your finger should not be on the trigger when you press the restart button.
3.1 - 3.4
(1 /8" - 9/64")
Screwdrivingoperation
Place the point of the driver bit in the
screw head and apply pressure to the tool.
Start
the tool slowly and then increase the
speed gradually. Release the trigger just
as
the screw bottoms out. The electric brake
will then stop the tool immediately, pre-
venting the screw and/or bit from being
damaged.
NOTE
:
*Make sure that the driver bit is inserted straight in the screw head, or the screw and/or
bitmay be damaged.
When driving wood screws, predrill Pilot
holes to make driving easier and to pre-
3.1 (1/8")
3.5(9/64") (3/32"
- 3/32")
vent splitting of the workpiece. See the
chart.
4.5(11/64") (7/64" - 1/8")
5.5 (7/32")
5.8 (I-'"'''
9

Drillingoperation
0 Drilling inwood
When drilling in wood, best results are obtainedwith wood drills equipped with
a guide
screw. The guide screw makes drilling easier by pulling the bit intothe workpiece.
0 Drilling inmetal
To preventthe bitfrom slippingwhen starting
a hole, make an indentationwith a center-
punch and hammer
at the point to be drilled. Place the point of the bit in the indenta-
tion and start drilling.
Use
a cutting lubricant when drilling metals. The exceptions are iron and brass which
should be drilled dry.
CAUTION:
*Pressing excessively on the tool will notspeed up the drilling. Infact, this excessive pres-
sure will only serve to damage the tip of your bit, decrease the tool performance and
shortenthe service lifeof the tool.
*There
is a tremendous force exerted on the tool/bit at the time of hole breakthrough.
Hold the tool firmly and exert care when the bit begins to break through the workpiece.
A stuck bit can be removed simply by setting the reversingswitch to reverse rotation in
order to back out. However, the tool may back out abruptly if you do nothold
it firm-
ly.
0 Always secure small workpieces in a vise or similar hold-downdevice.
10