Makita TD002G User manual

TD002G
EN Cordless Impact Driver INSTRUCTION MANUAL 5
SV Batteridriven
slagskruvdragare BRUKSANVISNING 18
NO Batteridrevet slagskrutrekker BRUKSANVISNING 30
FI Akkukäyttöinen iskuväännin KÄYTTÖOHJE 43
DA Akku slagskruemaskine BRUGSANVISNING 55
LV Bezvada triecienskrūvgriezis LIETOŠANAS INSTRUKCIJA 68
LT Belaidis smūginis suktuvas NAUDOJIMO INSTRUKCIJA 81
ET Juhtmeta löökkruvikeeraja KASUTUSJUHEND 94
RU Аккумуляторный ударный
шуруповерт РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ 106

2
2
3
1
1
Fig.1
1
2
Fig.2
1
Fig.3
1
AB
Fig.4
1
Fig.5
12
Fig.6
3
12
Fig.7

3
1
Fig.8
Fig.9
Fig.10

4
12
Fig.11
Fig.12
1 2
Fig.13
1 32
Fig.14
3
2
1
Fig.15
1
Fig.16
Fig.17

5ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: TD002G
Fastening capacities Machine screw M4 - M8
Standard bolt M5 - M16
High tensile bolt M5 - M14
No load speed (RPM) 4 (Max impact mode) 0 - 3,700 min-1
3 (Hard impact mode) 0 - 3,200 min-1
2 (Medium impact mode) 0 - 2,100 min-1
1 (Soft impact mode) 0 - 1,100 min-1
Wood mode 0 - 1,800 min-1
T mode (1) 0 - 2,900 min-1
T mode (2) 0 - 3,700 min-1
Bolt mode (1) * 0 - 2,700 min-1
Bolt mode (2) * 0 - 3,700 min-1
Bolt mode (3) * 0 - 3,700 min-1
Impacts per minute 4 (Max impact mode) 0 - 4,600 min-1
3 (Hard impact mode) 0 - 3,600 min-1
2 (Medium impact mode) 0 - 2,600 min-1
1 (Soft impact mode) 0 - 1,400 min-1
Wood mode 0 - 4,600 min-1
T mode (1) -
T mode (2) * 0 - 2,600 min-1
Bolt mode (1) -
Bolt mode (2) * 0 - 4,600 min-1
Bolt mode (3) * 0 - 4,600 min-1
Rated voltage D.C. 36 V - 40 V max
Overall length 119 mm
Net weight 1.7 - 2.9 kg
* Numerical values when rotated clockwise.
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydi󰀨erfromcountrytocountry.
• Theweightmaydi󰀨erdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
est combinations, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Batterycartridge BL4020* / BL4025* / BL4040* / BL4050F / BL4080F
*:Recommendedbattery
Charger DC40RA / DC40RB / DC40RC
• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof
residence.
WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges
andchargersmaycauseinjuryand/orre.

6ENGLISH
Intended use
The tool is intended for screw driving in wood, metal
and plastic.
Noise
ThetypicalA-weightednoiseleveldeterminedaccord-
ing to EN62841-2-2:
Sound pressure level (LpA) : 94 dB (A)
Sound power level (LWA) : 105 dB (A)
Uncertainty(K):3dB(A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
methodandmaybeusedforcomparingonetoolwith
another.
NOTE: The declared noise emission value(s)
mayalsobeusedinapreliminaryassessmentof
exposure.
WARNING: Wear ear protection.
WARNING: The noise emission during actual
use of the power tool can di󰀨er from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING: Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
o󰀨 and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-2:
Work mode: impact tightening of fasteners of the maxi-
mumcapacityofthetool
Vibration emission (ah) : 12.9 m/s2
Uncertainty(K):1.5m/s2
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
andmaybeusedforcomparingonetoolwithanother.
NOTE:Thedeclaredvibrationtotalvalue(s)mayalso
beusedinapreliminaryassessmentofexposure.
WARNING: The vibration emission during
actual use of the power tool can di󰀨er from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING: Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
o󰀨 and when it is running idle in addition to the
trigger time).
Declarations of Conformity
For European countries only
TheDeclarationsofconformityareincludedinAnnexA
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING Read all safety warnings, instructions,
illustrations and specications provided with this
power tool. Failure to follow all instructions listed below
mayresultinelectricshock,reand/orseriousinjury.
Save all warnings and instruc-
tions for future reference.
Theterm"powertool"inthewarningsreferstoyour
mains-operated(corded)powertoolorbattery-operated
(cordless) power tool.
Cordless impact driver safety
warnings
1. Hold the power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wiring.
Fastenerscontactinga"live"wiremaymake
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Always be sure you have a rm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool rmly.
4. Wear ear protectors.
5. Do not touch the bit or the workpiece immedi-
ately after operation. They may be extremely
hot and could burn your skin.
6. Keep hands away from rotating parts.
7. Use auxiliary handle(s), if supplied with the
tool.Lossofcontrolcancausepersonalinjury.
8. Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring.Cuttingaccessorycontactinga"live"
wiremaymakeexposedmetalpartsofthepower
tool "live" and could give the operator an electric
shock.
9. Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.

7ENGLISH
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble or tamper with the battery
cartridge.Itmayresultinare,excessiveheat,
or explosion.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge.Suchconductmayresultina
re,excessiveheat,orexplosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
Forcommercialtransportse.g.bythirdparties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Pleasealsoobservepossiblymoredetailed
national regulations.
Tapeormasko󰀨opencontactsandpackupthe
batteryinsuchamannerthatitcannotmove
around in the packaging.
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specied by Makita. Installing the batteries to
non-compliantproductsmayresultinare,exces-
siveheat,explosion,orleakofelectrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge.Itmaycauseheating,catchingre,
burstandmalfunctionofthetoolorbatterycar-
tridge,resultinginburnsorpersonalinjury.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines.Itmayresultinamalfunctionor
breakdownofthetoolorbatterycartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwill
alsovoidtheMakitawarrantyfortheMakitatooland
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).

8ENGLISH
FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery cartridge
CAUTION: Always switch o󰀨 the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge.Failuretoholdthetoolandthebattery
cartridgermlymaycausethemtoslipo󰀨yourhands
andresultindamagetothetoolandbatterycartridge
andapersonalinjury.
Toinstallthebatterycartridge,alignthetongueonthe
batterycartridgewiththegrooveinthehousingandslip
itintoplace.Insertitallthewayuntilitlocksinplace
withalittleclick.Ifyoucanseetheredindicatoras
showninthegure,itisnotlockedcompletely.
Toremovethebatterycartridge,slideitfromthetool
while sliding the button on the front of the cartridge.
►Fig.1: 1. Red indicator 2. Button 3.Batterycartridge
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
itmayaccidentallyfalloutofthetool,causinginjuryto
youorsomeonearoundyou.
CAUTION: Do not install the battery cartridge
forcibly.Ifthecartridgedoesnotslideineasily,itis
notbeinginsertedcorrectly.
Indicating the remaining battery capacity
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
light up for a few seconds.
►Fig.2: 1. Indicator lamps 2. Check button
Indicator lamps Remaining
capacity
Lighted O󰀨 Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
mayhave
malfunctioned.
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydi󰀨erslightly
fromtheactualcapacity.
NOTE:Therst(farleft)indicatorlampwillblinkwhen
thebatteryprotectionsystemworks.
Tool / battery protection system
Thetoolisequippedwithatool/batteryprotectionsys-
tem.Thissystemautomaticallycutso󰀨powertothe
motortoextendtoolandbatterylife.Thetoolwillauto-
maticallystopduringoperationifthetoolorbatteryis
placed under one of the following conditions:
Overload protection
Whenthebatteryisoperatedinamannerthatcauses
ittodrawanabnormallyhighcurrent,thetoolautomat-
icallystopswithoutanyindication.Inthissituation,turn
thetoolo󰀨andstoptheapplicationthatcausedthetool
to become overloaded. Then turn the tool on to restart.
Overheat protection
Whenthetoolorbatteryisoverheated,thetoolstops
automatically.Inthiscase,letthetoolandbatterycool
before turning the tool on again.
NOTE: When the tool is overheated, the lamp blinks.
Overdischarge protection
Whenthebatterycapacityisnotenough,thetoolstops
automatically.Inthiscase,removethebatteryfromthe
toolandchargethebattery.
Protections against other causes
Protectionsystemisalsodesignedforothercauses
that could damage the tool and allows the tool to stop
automatically.Takeallthefollowingstepstoclearthe
causes,whenthetoolhasbeenbroughttoatemporary
halt or stop in operation.
1.
Turnthetoolo󰀨,andthenturnitonagaintorestart.
2. Chargethebattery(ies)orreplaceit/themwith
rechargedbattery(ies).
3. Letthetoolandbattery(ies)cooldown.
Ifnoimprovementcanbefoundbyrestoringprotection
system,thencontactyourlocalMakitaServiceCenter.
Switch action
CAUTION: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
Tostartthetool,simplypulltheswitchtrigger.Tool
speedisincreasedbyincreasingpressureontheswitch
trigger. Release the switch trigger to stop.
►Fig.3: 1. Switch trigger
NOTE:Thetoolautomaticallystopsifyoukeeppull-
ing the switch trigger for about 6 minutes.
NOTE:Whilepullingtheswitchtrigger,anyother
buttons do not work.

9ENGLISH
Reversing switch action
CAUTION: Always check the direction of
rotation before operation.
CAUTION: Use the reversing switch only after
the tool comes to a complete stop. Changing the
directionofrotationbeforethetoolstopsmaydam-
age the tool.
CAUTION: When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
►Fig.4: 1. Reversing switch lever
Electric brake
This tool is equipped with an electric brake. If the tool
consistentlyfailstoquicklystopaftertheswitchtrigger
is released, have the tool serviced at a Makita service
center.
Lighting up the front lamp
CAUTION: Do not look in the light or see the
source of light directly.
►Fig.5: 1. Front lamp
Pull the switch trigger to turn on the front lamps. To turn
o󰀨,releasetheswitchtrigger.Thefrontlampsgoout
approximately10secondsafterreleasingtheswitch
trigger.
Todisablethefrontlamps,turno󰀨thelampstatus.To
turno󰀨thelampstatus,rstpullandreleasetheswitch
trigger. Within 10 seconds after releasing the switch
trigger, press and hold the button for a few seconds.
Whenthelampstatusiso󰀨,thefrontlampswillnotturn
on even if the trigger is pulled.
To turn on the lamp status again, press and hold the
button for a few seconds.
►Fig.6: 1. Button 2. Switch panel
NOTE: When the tool is overheated, the front lamps
ashforoneminute,andthentheswitchpanelgoes
o󰀨.Inthiscase,cooldownthetoolbeforeoperating
again.
NOTE:Toconrmthelampstatus,pullthetrigger
when the reversing switch lever is not in the neutral
position.Whenthefrontlampslightupbypullingthe
switch trigger, the lamp status is on. When the front
lampsdonotlightup,thelampstatusiso󰀨.
NOTE:Useadryclothtowipethedirto󰀨thelensof
the front lamps. Be careful not to scratch the lens of
frontlamps,oritmaylowertheillumination.
Light mode
Youcanusethetoolasahandylight.
Turning on / o󰀨 the light mode
To turn on the light, set the reversing switch lever in the
neutral position and pull the switch trigger.
Thelampkeepslightingupforapproximatelyonehour.
Toturno󰀨thelightmode,pulltheswitchtriggeragainor
depress the reversing switch lever.
NOTE: You cannot change the application mode
while the light mode is on. The lamps on the switch
panel do not turn on when the light mode is on.
NOTE:Youcannotturnon/o󰀨thelampstatusor
change the application mode when the light mode is
on.
NOTE: The light mode does not work when the tool/
batteryprotectionsystemactivatesorthebattery
capacityisnotenough.
Changing brightness
Press the button while the light mode is operating.
Thebrightnessdecreaseseverytimeyoupressthe
button . The brightness will return to the highest when
operating in the lowest brightness. The brightness can
beadjustedin3steps.
NOTE: The light turns on at the same brightness as
the last setting.
NOTE: The brightness during driving tool will be the
same as the brightness set in the light mode.
Changing the application mode
What's the application mode?
The application mode is the variation of the driving
rotationandimpactwhicharealreadypresetinthetool.
Bychoosingasuitableapplicationmodedependingon
thework,youcanaccomplishquickerworkand/ormore
beautifulnish.
This tool features following application modes:
Impact force
• 4 (Max)
• 3 (Hard)
• 2 (Medium)
• 1 (Soft)
Assist type
• Wood mode
• T mode (1)
• T mode (2)
• Bolt mode (1) (clockwise/counterclockwise)
• Bolt mode (2) (clockwise/counterclockwise)
• Bolt mode (3) (clockwise/counterclockwise)
Theapplicationmodecanbechangedbythebut-
ton , , or the quick mode-switching button.
►Fig.7: 1. Quick mode-switching button
2. Button 3. Button

10 ENGLISH
Byregisteringacertainapplicationmodetothetool,
youcanswitchtotheregisteredapplicationmodeby
justpressingthequickmode-switchingbutton(quick
mode-switching function).
NOTE: When none of the lamp on the panel is lit,
pull the switch trigger once before pressing the quick
mode-switching button.
NOTE: You will not be able to change the application
modeifyoudonotoperatethetoolforapproximately
one minute. In this case, pull the switch trigger
once and press the button , button , or quick
mode-switching button.
NOTE: Refer to "Registering the application mode"
in "Quick mode-switching function" section for how to
register the application mode.
Quick mode-switching button
The function of the quick mode-switching button varies
dependingonwhetheryouhaveregisteredtheapplica-
tion mode to the tool.
►Fig.8: 1. Quick mode-switching button
When the application mode is not
registered:
Thelevelofimpactforcechangeseverytimeyoupress
the quick mode-switching button. The front lamps will
ashoncewhentheimpactforceischangedbypress-
ing the quick mode-switching button.
When the application mode is registered:
The tool switches between the registered application
modeandcurrentapplicationmodeeverytimeyou
press the quick mode-switching button. The front lamps
willashoncewhentheapplicationmodeischangedby
pressing the quick mode-switching button.
NOTE:Whenthelampstatusiso󰀨,thefrontlamps
willnotashevenwhentheapplicationmodeis
changedbypressingthequickmode-switching
button.
NOTE: Refer to "Registering the application mode"
in "Quick mode-switching function" section for how to
register the application mode.
Disabling the quick mode-switching
button
You can also disable the quick mode-switching button.
After disabling, the quick mode-switching button will not
work for changing the impact force and switching the
application mode.
To disable the quick mode-switching button, press and
hold the quick mode-switching button and the but-
ton at the same time until the all lamps on the panel
blink.
To resume the quick mode-switching button, perform
the same procedure as above again.
NOTE: Registering and erasing the application mode
can be performed even if the quick mode-switching
button is disabled. After registering or erasing the
application mode, the quick mode-switching button
will be activated.

11 ENGLISH
Quick reference
The following table shows the functions of the quick mode-switching button.
indicates the quick mode-switching button.
Button(s) / Purpose Action How to conrm
(When the application mode is not
registered)
Changing the impact force by the quick
mode-switching button
Press
Thefrontlampsonthetoolashonce.
(When the application mode is regis-
tered)
Switching to the registered application
mode
Press
Thefrontlampsonthetoolashonce.
Registering the application mode
Press and hold (each button) Example: Wood mode is registered
The lamp of desired application mode
blinks.
Erasing the registered application mode
Press and hold (each button)
All impact force grade lamps blink.
Disabling the quick mode-switching
button
Press and hold (each button)
All lamps on the panel blink.
(When the application mode is regis-
tered)
Resuming the quick mode-switching
button
Press and hold (each button) Example: Wood mode is registered
The lamp of desired application mode
blinks.
(When the application mode is not
registered)
Resuming the quick mode-switching
button
Press and hold (each button)
All impact force grade lamps blink.
: The lamp is blinking.

12 ENGLISH
Changing the impact force
You can change the impact force in four steps: 4 (max), 3 (hard), 2 (medium), and 1 (soft).
This allows a tightening suitable to the work.
Thelevelofimpactforcechangeseverytimeyoupressthebutton .
Whentheapplicationmodeisnotregistered,thelevelofimpactforcealsochangesbythequickmode-switching
button.
Youcanchangetheimpactforcewithinapproximatelyoneminuteafterreleasingtheswitchtrigger.
NOTE:Youcanextendthetimetochangetheimpactforceapproximatelyoneminuteifyoupressthebut-
ton , , or the quick mode-switching button.
►Fig.9
Application mode
(Impact force grade
displayed on panel)
Maximum blows Purpose Example of application
4 (Max) 4,600 min-1 (/min) Tightening with the maximum force
and speed.
Driving screws to underwork materi-
als, tightening long screws or bolts.
3 (Hard) 3,600 min-1 (/min) Tightening with less force and speed
than Max mode (easier to control than
Max mode).
Driving screws to underwork materi-
als, tightening bolts.
2 (Medium) 2,600 min-1 (/min) Tighteningwhenagoodnishingis
needed.
Drivingscrewstonishingboardsor
plaster boards.
1 (Soft) 1,400 min-1 (/min) Tightening with less force to avoid
screw thread breakage.
Tightening sash screws or small
screws such as M6.
: The lamp is on.
NOTE: When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button or the
quick mode-switching button.
NOTE:Alllampsontheswitchpanelgooutwhenthetoolisturnedo󰀨tosavethebatterypower.Theimpactforce
gradecanbecheckedbypullingtheswitchtriggertotheextentthatthetooldoesnotoperate.

13 ENGLISH
Changing assist type
Thistoolemploysassistfunctionthato󰀨ersseveraleasy-to-useapplicationmodesfordrivingscrewswithgoodcontrol.
Thetypeoftheapplicationmodechangeseverytimeyoupressthebutton .
Youcanchangetheassisttypewithinapproximatelyoneminuteafterreleasingtheswitchtrigger.
NOTE:Youcanextendthetimetochangetheassisttypeapproximatelyoneminuteifyoupressthebutton , ,
or the quick mode-switching button.
►Fig.10
Application mode
(Assist type displayed
on panel)
Maximum blows Feature Purpose
Wood mode * 4,600 min-1 (/min) This mode helps to prevent a screw from falling at
the beginning of driving. The tool drives a screw
withlow-speedrotationatrst.Afterthetoolstarts
to impact, the rotation speed increases and reaches
the maximum speed.
Tightening long screws.
T mode (1) * –
(The tool stops rotating
soon after impact starts.)
This mode helps to prevent the screws from
over-tightening. It also accomplishes quick oper-
ationandgoodnishatthesametime.Thetool
drives a screw with high-speed rotation and stops
soon after the tool starts to impact.
NOTE:
The timing to stop the driving varies depending
on the type of the screw and material to be driven.
Make a test driving before using this mode.
Driving self-drilling
screws to a thin metal
platewithgoodnish.
T mode (2) * 2,600 min-1 (/min) This mode helps to prevent the screws from
breakage and stripping. It also accomplishes quick
operationandgoodnishatthesametime.Thetool
drives a screw with high-speed rotation and slows
down the rotation when the tool starts to impact.
NOTE:
Release the switch trigger as soon as the tight-
ening nished to avoid overtightening.
Driving self-drilling
screws to a thick metal
platewithgoodnish.
Bolt mode –Clockwise
Thismodehelpstorepeatscrewdrivingcontinuously
with equal torque. The stroke of the switch trigger to
reach maximum speed will become short in this mode.
Counterclockwise
Thismodehelpstopreventaboltfromfallingo󰀨.
When loosening a bolt with the tool driving in coun-
terclockwiserotation,thetoolautomaticallystopsor
slows down after the bolt/nut gets enough loosened.
The stroke of the switch trigger to reach maximum
speed will become short in this mode.
NOTE:
The timing to stop the driving varies depending
on the type of the screw and material to be driven.
Make a test driving before using this mode.
Clockwise
Preventing over tighten-
ing of bolts.
Counterclockwise
Loosening bolts.
Bolt mode (1) –Clockwise
Thetoolstopsautomaticallyassoonasithas
started impact blows.
Counterclockwise
Theimpactforceis2.Thetoolstopsautomatically
as soon as it has stopped impacting.
–
Bolt mode (2) 4,600 min-1 (/min) Clockwise
Thetoolstopsautomaticallyapproximately0.3secondlater
from the moment that the tool has started impact blows.
Counterclockwise
Theimpactforceis4.Thetoolstopsautomatically
as soon as it has stopped impacting.
–
Bolt mode (3) 4,600 min-1 (/min) Clockwise
Thetoolstopsautomaticallyapproximately1secondlater
from the moment that the tool has started impact blows.
Counterclockwise
The tool slows down the rotation after it has stopped
impacting.
–
: The lamp is on.
*
When the tool rotates counterclockwise, the impact per minute is the same as in 4 (max) mode, 4,600 min-1 (/min).

14 ENGLISH
NOTE: When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button .
NOTE:Alllampsontheswitchpanelgooutwhenthetoolisturnedo󰀨tosavethebatterypower.Thetypeofthe
applicationmodecanbecheckedbypullingtheswitchtriggertotheextentthatthetooldoesnotoperate.
Quick mode-switching function
What you can do with the quick mode-switching function
The quick mode-switching function saves the time for changing the application mode of the tool. You can switch to
yourdesiredapplicationmodebyjustpressingthequickmode-switchingbutton.Itishelpfulwhendoingarepetitive
workwhichrequirestoswitchbetweentwoapplicationmodesalternately.
EXAMPLEIfyouhaveaworktouseTmodeandmaximpactforce,registerthemaximpactforceforquick
mode-switchingfunction.Onceregisterit,youcanswitchtothemaximpactforcefromTmodebyjustoneclick
ofthequickmode-switchingbutton.Also,youcanreturntoTmodebypressingthequickmode-switchingbutton
again.
Even if the tool is in other application mode than T mode, pressing the quick mode-switching button changes to
maximpactforce.Itisconvenientforyoutoregisteranapplicationmodethatyoufrequentlyuse.
You can choose one of following application modes for quick mode-switching function:
Impact force
• 4 (Max)
• 3 (Hard)
• 2 (Medium)
• 1 (Soft)
Assist type
• Wood mode
• T mode (1)
• T mode (2)
• Bolt mode (1) (clockwise/counterclockwise)
• Bolt mode (2) (clockwise/counterclockwise)
• Bolt mode (3) (clockwise/counterclockwise)
Registering application mode
Tousethequickmode-switchingfunction,registeryourdesiredapplicationmodetothetoolbeforehand.
1. With the button or ,chooseyourdesiredapplicationmode.
2. Press and hold the button and the quick mode-switching button at the same time until the lamp of desired
application mode blinks.
►Fig.11: 1. Quick mode-switching button 2. Button
NOTE:Youcanoverwritethecurrentapplicationmodewithnewonebyperformingtheprocedureabove.
Using the quick mode-switching function
When the tool is in the mode that is not registered, press the quick mode-switching button to switch to the registered
applicationmode.Thetoolswitchesbetweentheregisteredapplicationmodeandlastapplicationmodeeverytime
youpressthequickmode-switchingbutton.Thefrontlampswillashoncewhenswitchingtotheregisteredapplica-
tion mode.
The lamp of the registered application mode will blink when using the registered application mode.

15 ENGLISH
Erasing the quick mode-switching function
Press and hold the button and button at the same time until all impact force grade lamps blink.
NOTE: After erasing the quick mode-switching function, the quick mode-switching button works for changing the
impact force.
Indication patterns
Application mode While registering the application mode When the registered application mode
turns on
4 (Max)
3 (Hard)
2 (Medium)
1 (Soft)
Wood mode
T mode (1)
T mode (2)
Bolt mode (1)
Bolt mode (2)
Bolt mode (3)
: The lamp is on.
: The lamp is blinking.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
socket bit
Useonlydriverbit/socketbitthathasinsertingportion
showninthegure.Donotuseanyotherdriverbit/
socket bit.
►Fig.12
For tool with shallow driver bit hole
A=12mm
B=9mm
Useonlythesetypesofdriver
bits. Follow the procedure
1. (Note) Bit-piece is not
necessary.
For tool with deep driver bit hole
A=17mm
B=14mm
Toinstallthesetypesofdriver
bits, follow the procedure 1.
A=12mm
B=9mm
Toinstallthesetypesofdriver
bits, follow the procedure 2.
(Note)Bit-pieceisnecessary
for installing the bit.

16 ENGLISH
Procedure 1
For tool without one-touch type sleeve
To install the driver bit, pull the sleeve in the direction of
the arrow and insert the driver bit into the sleeve as far
as it will go.
Then release the sleeve to secure the driver bit.
►Fig.13: 1. Driver bit 2. Sleeve
For tool with one-touch type sleeve
To install the driver bit, insert the driver bit into the
sleeve as far as it will go.
Procedure 2
In addition to Procedure 1, insert the bit-piece into the
sleeve with its pointed end facing in.
►Fig.14: 1. Driver bit 2. Bit-piece 3. Sleeve
To remove the driver bit, pull the sleeve in the direction
of the arrow and pull the driver bit out.
NOTE: If the driver bit is not inserted deep enough
into the sleeve, the sleeve will not return to its original
position and the driver bit will not be secured. In this
case,tryre-insertingthebitaccordingtotheinstruc-
tions above.
NOTE:Whenitisdi󰀩culttoinsertthedriverbit,pull
the sleeve and insert it into the sleeve as far as it will
go.
NOTE: After inserting the driver bit, make sure that it
isrmlysecured.Ifitcomesout,donotuseit.
Installing hook
WARNING: Use the hanging/mounting parts
for their intended purposes only, e.g., hanging the
tool on a tool belt between jobs or work intervals.
WARNING: Be careful not to overload the
hook as too much force or irregular overburden
may cause damages to the tool resulting in per-
sonal injury.
CAUTION: When installing the hook, always
secure it with the screw rmly. If not, the hook
maycomeo󰀨fromthetoolandresultinthepersonal
injury.
CAUTION: Make sure to hang the tool
securely before releasing your hold.Insu󰀩cient
orunbalancedhookingmaycausefallingo󰀨andyou
maybeinjured.
Thehookisconvenientfortemporarilyhangingthetool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
►Fig.15: 1. Groove 2. Hook 3. Screw
Using hole
WARNING: Never use the hanging hole for
unintended purpose, for instance, tethering the
tool at high location.Bearingstressinaheavily
loadedholemaycausedamagestothehole,result-
ingininjuriestoyouorpeoplearoundorbelowyou.
Use the hanging hole at the bottom rear of the tool to
hang the tool on a wall using a hanging cord or similar
strings.
►Fig.16: 1. Hanging hole
OPERATION
Theproperfasteningtorquemaydi󰀨erdependingupon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between fas-
teningtorqueandfasteningtimeisshowninthegures.
►Fig.17
The relation between fastening torque and fasten-
ing time for standard bolt (when impact force is 4)
N•m
(kgf•cm)
M14
M12
M10
M8
(M16)
(M14)
(M12)
(M10)
(M8)
M16
140
(1428)
(1224)
(1020)
(816)
(612)
(408)
(204)
120
100
80
60
40
20
0
23
1
0.60.20.4
1. Fastening time (second) 2. Fastening torque
3. Proper fastening torque corresponding to each bolt
diameter

17
The relation between fastening torque and fastening
time for high tensile bolt (when impact force is 4)
200
180
160
140
120
100
80
60
40
20
N•m
(kgf•cm)
(2040)
(1836)
(1632)
(1428)
(1224)
(1020)
(816)
(612)
(408)
(204)
012
23
1
M14
M12
(M14)
(M12)
(M10)
(M8)
M10
M8
1. Fastening time (second) 2. Fastening torque
3. Proper fastening torque corresponding to each bolt
diameter
Holdthetoolrmlyandplacethepointofthedriverbit
inthescrewhead.Applyforwardpressuretothetoolto
theextentthatthebitwillnotslipo󰀨thescrewandturn
the tool on to start operation.
NOTICE: If you use a spare battery to continue
the operation, rest the tool at least 15 min.
NOTE: Use the proper bit for the head of the screw/
boltthatyouwishtouse.
NOTE: When fastening M8 or smaller screw, choose
aproperimpactforceandcarefullyadjustpressureon
the switch trigger so that the screw is not damaged.
NOTE: Hold the tool pointed straight at the screw.
NOTE:Iftheimpactforceistoostrongoryoutighten
thescrewforatimelongerthanshowninthegures,
thescreworthepointofthedriverbitmaybeover-
stressed,stripped,damaged,etc.Beforestartingyour
job,alwaysperformatestoperationtodeterminethe
properfasteningtimeforyourscrew.
Thefasteningtorqueisa󰀨ectedbyawidevarietyof
factorsincludingthefollowing.Afterfastening,always
check the torque with a torque wrench.
1. Whenthebatterycartridgeisdischargedalmost
completely,voltagewilldropandthefastening
torque will be reduced.
2. Driver bit or socket bit
Failure to use the correct size driver bit or socket
bit will cause a reduction in the fastening torque.
3. Bolt
• Eventhoughthetorquecoe󰀩cientandthe
class of bolt are the same, the proper fasten-
ingtorquewilldi󰀨eraccordingtothediame-
ter of bolt.
• Even though the diameters of bolts are the
same,theproperfasteningtorquewilldi󰀨er
accordingtothetorquecoe󰀩cient,theclass
of bolt and the bolt length.
4. The manner of holding the tool or the material
ofdrivingpositiontobefastenedwilla󰀨ectthe
torque.
5. Operating the tool at low speed will cause a reduc-
tion in the fastening torque.
MAINTENANCE
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers,alwaysusingMakitareplacementparts.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual.Theuseofanyother
accessories or attachments might present a risk of
injurytopersons.Onlyuseaccessoryorattachment
for its stated purpose.
Ifyouneedanyassistanceformoredetailsregard-
ingtheseaccessories,askyourlocalMakitaService
Center.
• Driver bits
• Socket bits
• Hook
• Tool hanger
• Plasticcarryingcase
• Makitagenuinebatteryandcharger
NOTE:Someitemsinthelistmaybeincludedinthe
toolpackageasstandardaccessories.Theymay
di󰀨erfromcountrytocountry.
ENGLISH

18 SVENSKA
SVENSKA (Originalinstruktioner)
SPECIFIKATIONER
Modell: TD002G
Åtdragningskapaciteter Maskinskruv M4 - M8
Standardbult M5 - M16
Höghållfasta bultar M5 - M14
Hastighet utan belastning
(RPM)
4 (Max slagläge) 0 - 3 700 min-1
3 (Hårt slagläge) 0 - 3 200 min-1
2 (Medelslagläge) 0 - 2 100 min-1
1(Mjuktslagläge) 0 - 1 100 min-1
Träläge 0 - 1 800 min-1
T-läge (1) 0 - 2 900 min-1
T-läge (2) 0 - 3 700 min-1
Bultläge (1) * 0 - 2 700 min-1
Bultläge (2) * 0 - 3 700 min-1
Bultläge (3) * 0 - 3 700 min-1
Slag per minut 4 (Max slagläge) 0 - 4 600 min-1
3 (Hårt slagläge) 0 - 3 600 min-1
2 (Medelslagläge) 0 - 2 600 min-1
1(Mjuktslagläge) 0 - 1 400 min-1
Träläge 0 - 4 600 min-1
T-läge (1) -
T-läge (2) * 0 - 2 600 min-1
Bultläge (1) -
Bultläge (2) * 0 - 4 600 min-1
Bultläge (3) * 0 - 4 600 min-1
Märkspänning 36 V - 40 V likström max
Total längd 119 mm
Nettovikt 1,7 - 2,9 kg
* Numeriska värden vid medurs rotation.
• Pågrundavvårtpågåendeprogramförforskningochutvecklingkandessaspecikationerändrasutanföregå-
ende meddelande.
• Specikationerkanvarieramellanolikaländer.
• Viktenkanvarieraberoendepåtillbehören,inklusivebatterikassett.Denlättasteochdentyngstakombinatio-
nen enligt EPTA-procedur 01/2014 visas i tabellen.
Tillgänglig batterikassett och laddare
Batterikassett BL4020* / BL4025* / BL4040* / BL4050F / BL4080F
* : Rekommenderat batteri
Laddare DC40RA / DC40RB / DC40RC
• Vissaavbatterikassetternaochladdarnapålistanovankanskeintennstillgängligaidinregion.
VARNING: Använd endast batterikassetter och laddare från listan ovan. Användning av andra batterikas-
setter och laddare kan orsaka personskada och/eller brand.

19 SVENSKA
Avsedd användning
Verktygetäravsettförskruvdragningiträ,metallochplast.
Buller
Den normala bullernivån för A-belastning är bestämd
enligt EN62841-2-2:
Ljudtrycksnivå(LpA) : 94 dB (A)
Ljude󰀨ektnivå(LWA) : 105 dB (A)
Mättolerans(K):3dB(A)
OBS: Det deklarerade bullervärdet har uppmätts i
enlighet med standardtestmetoden och kan användas
förjämförandetavenmaskinmedenannan.
OBS: Det deklarerade bulleremissionsvärdet kan
också användas i en preliminär bedömning av expo-
nering för vibration.
VARNING: Använd hörselskydd.
VARNING: Bulleremissionen under faktisk
användning av maskinen kan skilja sig från det
deklarerade värdet, beroende på hur maskinen
används och särskilt vilken typ av arbetsstycke
som behandlas.
VARNING: Var noga med att identiera säker-
hetsåtgärder för att skydda användaren, vilka är
grundade på en uppskattning av graden av expo-
nering för vibrationer under de faktiska använd-
ningsförhållandena, (ta, förutom avtryckartiden,
med alla delar av användarcykeln i beräkningen,
som till exempel tiden då maskinen är avstängd
och när den går på tomgång).
Vibration
Det totala vibrationsvärdet (treaxlad vektorsumma)
bestämt enligt EN62841-2-2:
Arbetsläge: maskinens maximala kapacitet för
slagåtdragning
Vibrationsemission (ah) : 12,9 m/s2
Mättolerans(K):1,5m/s2
OBS: Det deklarerade totala vibrationsvärdet har
uppmätts i enlighet med standardtestmetoden och
kananvändasförjämförandetavenmaskinmeden
annan.
OBS: Det deklarerade totala vibrationsvärdet kan
också användas i en preliminär bedömning av expo-
nering för vibration.
VARNING: Vibrationsemissionen under fak-
tisk användning av maskinen kan skilja sig från
det deklarerade värdet, beroende på hur maski-
nen används och särskilt vilken typ av arbetss-
tycke som behandlas.
VARNING: Var noga med att identiera säker-
hetsåtgärder för att skydda användaren, vilka är
grundade på en uppskattning av graden av expo-
nering för vibrationer under de faktiska använd-
ningsförhållandena, (ta, förutom avtryckartiden,
med alla delar av användarcykeln i beräkningen,
som till exempel tiden då maskinen är avstängd
och när den går på tomgång).
Försäkran om överensstämmelse
Gäller endast inom EU
Försäkran om överensstämmelse ingår i bilaga A till
denna bruksanvisning.
SÄKERHETSVARNINGAR
Allmänna säkerhetsvarningar för maskiner
VARNING Läs alla säkerhetsvarningar, instruktioner,
illustrationer och specikationer som medföljer detta
elverktyg.Underlåtenhetattföljaallainstruktionernedankan
leda till elstötar, brand och/eller allvarliga personskador.
Spara alla varningar och instruk-
tioner för framtida referens.
Termen ”maskin” som anges i varningarna hänvisar till
din eldrivna maskin (sladdansluten) eller batteridrivna
maskin (sladdlös).
Säkerhetsvarningar för batteridriven
slagskruvdragare
1. Håll maskinen i de isolerade handtagen om det
nns risk för att skruvdragaren kan komma i
kontakt med en dold elkabel. Skruvdragare som
kommer i kontakt med en ”strömförande” kabel
kan få sina blottlagda metalldelar ”strömförande”,
vilket kan ge användaren en elektrisk stöt.
2. Se till att alltid ha ordentligt fotfäste.
Se till att ingen står under dig när maskinen
används på hög höjd.
3. Håll stadigt i maskinen.
4. Använd hörselskydd.
5. Rör inte bits eller arbetsstycket direkt efter
arbetet. De kan vara extremt varma och kan
orsaka brännskador.
6. Håll händerna på avstånd från roterande delar.
7. Använd extrahandtag om det levereras med
maskinen. Om du förlorar kontrollen över maski-
nen kan det leda till personskador.
8. Håll maskinen i de isolerade handtagen om det
nns risk för att skärverktyget kan komma i
kontakt med en dold elkabel.Omskärverktyget
kommer i kontakt med en ”strömförande” ledning
blir maskinens blottlagda metalldelar ”strömfö-
rande” och kan ge operatören en elektrisk stöt.
9. Se till att det inte nns några elkablar, vatten-
rör, gasledningar etc. som kan orsaka fara om
de skadas av verktyget.
SPARA DESSA ANVISNINGAR.
VARNING: GLÖM INTE att också fortsätt-
ningsvis strikt följa säkerhetsanvisningarna för
maskinen även efter att du blivit van att använda
den.
Vid FELAKTIG HANTERING av maskinen eller om
inte säkerhetsanvisningarna i denna bruksanvis-
ning följs kan följden bli allvarliga personskador.

20 SVENSKA
Viktiga säkerhetsanvisningar för
batterikassetten
1. Innan batterikassetten används ska alla instruk-
tioner och varningsmärken på (1) batteriladda-
ren, (2) batteriet och (3) produkten läsas.
2. Montera inte isär eller mixtra med batterikassetten.
Det kan leda till brand, överdriven värme eller explosion.
3. Om drifttiden blivit avsevärt kortare ska använd-
ningen avbrytas omedelbart. Det kan uppstå
överhettning, brännskador och t o m en explosion.
4. Om du får elektrolyt i ögonen ska de sköljas
med rent vatten och läkare uppsökas omedel-
bart. Det nns risk för att synen förloras.
5. Kortslut inte batterikassetten.
(1) Rör inte vid polerna med något strömfö-
rande material.
(2) Undvik att förvara batterikassetten till-
sammans med andra metallobjekt som
t.ex. spikar, mynt o.s.v.
(3) Skydda batteriet mot vatten och regn.
En batterikortslutning kan orsaka ett stort ström-
öde, överhettning, brand och maskinhaveri.
6. Förvara och använd inte verktyget och batterikassetten
på platser där temperaturen kan nå eller överstiga 50 °C.
7. Bränn inte upp batterikassetten även om
den är svårt skadad eller helt utsliten.
Batterikassetten kan explodera i öppen eld.
8.
Spika inte i, krossa, kasta, tappa eller slå batteri-
kassetten mot hårda föremål.Dylikahändelserkan
leda till brand, överdriven värme eller explosion.
9. Använd inte ett skadat batteri.
10.
De medföljande litiumjonbatterierna är föremål
för kraven i gällande lagstiftning för farligt gods.
Förkommersiellatransporter(avt.ex.tredjeparter
somspeditionsrmor)måstedesärskildatransport-
krav som anges på emballaget och etiketter iakttas.
För att förbereda den produkt som ska avsändas
krävs att du konsulterar en expert på riskmaterial.
Var också uppmärksam på att det i ditt land kan
nnasytterligareföreskrifterattfölja.
Tejpaöverellermaskerablottadekontakterochpackabatteriet
på sådant sätt att det inte kan röra sig fritt i förpackningen.
11. När batterikassetten ska kasseras måste den tas bort
från maskinen och kasseras på ett säkert sätt. Följ lokala
föreskrifter beträ󰀨ande avfallshantering av batteriet.
12. Använd endast batterierna med de produkter som
specicerats av Makita. Att använda batterierna
medejgodkändaprodukterkanledatillbrand,över-
drivenvärme,explosionellerutläckandeelektrolyt.
13. Om maskinen inte används under en lång tid
måste batteriet tas bort från maskinen.
14. Under och efter användning kan batterikasset-
ten bli het vilket kan orsaka brännskador eller
lättare brännskador. Var uppmärksam på hur
du hanterar varma batterikassetter.
15.
Vidrör inte verktygets kontakter direkt efter använd-
ning eftersom de kan bli heta och orsaka brännskador.
16. Låt inte isor, damm eller smuts fastna i kontak-
terna, i hål eller spår i batterikassetten. Det kan
ledatillattverktygetellerbatterikassettenvärmsupp,
fattar eld, går sönder eller inte fungerar som de ska,
vilket kan orsaka brännskador eller personskador.
17. Såvida inte verktyget stöder arbeten i närheten
av högspänningsledningar får batterikassetten
inte användas i närheten av en högspännings-
ledning.Detkanledatillattverktygetellerbatteri-
kassetten går sönder eller inte fungerar korrekt.
18. Förvara batteriet utom räckhåll för barn.
SPARA DESSA ANVISNINGAR.
FÖRSIKTIGT: Använda endast äkta Makita-
batterier. Användning av oäkta Makita-batterier eller
batterier som har manipulerats kan leda till person-
och utrustningsskador eller till att batteriet fattar eld.
DetupphäverocksåMakitasgarantiförverktygetoch
laddaren.
Tips för att uppnå batteriets max-
imala livslängd
1. Ladda batterikassetten innan den är helt
urladdad. Stanna alltid maskinen och ladda
batterikassetten när du märker att maskinen
blir svagare.
2. Ladda aldrig en fulladdad batterikassett.
Överladdning förkortar batteriets livslängd.
3. Ladda batterikassetten vid en rumstemperatur
på 10 °C - 40 °C. Låt en varm batterikassett
svalna innan den laddas.
4. När batterikassetten inte används ska den tas
bort från verktyget eller laddaren.
5. Ladda batterikassetten om du inte har använt
den på länge (mer än sex månader).
FUNKTIONSBESKRIVNING
FÖRSIKTIGT: Se alltid till att maskinen är
avstängd och batterikassetten borttagen innan
du justerar maskinen eller kontrollerar dess
funktioner.
Montera eller demontera
batterikassetten
FÖRSIKTIGT: Stäng alltid av maskinen innan
du monterar eller tar bort batterikassetten.
FÖRSIKTIGT: Håll stadigt i maskinen och
batterikassetten när du monterar eller tar bort
batterikassetten. I annat fall kan det leda till att de
glider ur dina händer och orsakar skada på maskinen
och batterikassetten samt personskada.
Sätt i batterikassetten genom att rikta in tungan på bat-
terikassettenmotspåretihöljetochskjutdenpåplats.
Tryckinbatterikassettenordentligttillsdenlåserfast
med ett klick. Om du kan se den röda indikatorn som
bilden visar är den inte låst ordentligt.
Tabortbatterikassettengenomattskjutanerknap-
pen på kassettens framsida samtidigt som du drar ut
batterikassetten.
►Fig.1: 1. Röd indikator 2.Knapp3. Batterikassett