Makita DDG460 User manual

DDG460
EN Cordless Earth Auger INSTRUCTION MANUAL 5
SV Trådlös jordborr BRUKSANVISNING 12
NO Batteridrevet jordbor BRUKSANVISNING 19
FI Akkukäyttöinen maakaira KÄYTTÖOHJE 26
DA Akku jordbor BRUGSANVISNING 33
LV Bezvadu spirālveida zemes
urbis LIETOŠANAS INSTRUKCIJA 40
LT Belaidis žemės grąžtas NAUDOJIMO INSTRUKCIJA 47
ET Juhtmeta pinnasepuur KASUTUSJUHEND 54
RU Бур аккумуляторный РУКОВОДСТВО ПО
ЭКСПЛУАТАЦИИ 61

H
1
3 4
5 6
7 8
2
ABC
ABC
Fig.1
1
1
Fig.2
1
3 2
3
2
Fig.3
2
1
2
1
Fig.4
1
2
Fig.5
1
Fig.6
2

1
Fig.7
1
Fig.8
1
A
B
Fig.9
1
Fig.10
1
2
3
Fig.11
1
Fig.12
1
2
3
Fig.13
1
2
3
Fig.14
3

Fig.15
1
2
Fig.16
1
2
Fig.17
1
2
33
1
2
Fig.18
Fig.19
Fig.20
4

5ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: DDG460
No load speed High 0 - 1,400 min-1
Low 0 - 350 min-1
Drilling capacities For sandy soil: 200 mm
For clay soil: 150 mm
Overall length 840 mm
Rated voltage D.C. 36 V
Net weight 7.3 - 8.2 kg
• Due to our continuing program of research and development, the specications herein are subject to change without notice.
• Specications may di󰀨er from country to country.
• The weight may di󰀨er depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or re.
Intended use
The tool is intended for drilling the ground.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-1:
Sound pressure level (LpA) : 85 dB(A)
Sound power level (LWA) : 96 dB (A)
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING: Wear ear protection.
WARNING: The noise emission during actual
use of the power tool can di󰀨er from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING: Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched o󰀨 and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-1:
Vibration emission (ah,D) : 2.5 m/s2or less
Uncertainty (K) : 1.5 m/s2
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.