Malibu Boats HYANNIS COUNTER SWIVEL CHAIR MHYA-DCC-S-R User manual

Hardware and Parts
2.75
F(6)
C(4)
(4)
( Seat Back Assembly )
Q
K
(Right Arm)
Assembly
(Seat Bottom)
Assembly
(4)
D
1.50
A(16)
B(4)
3.50
E
L
(Left Arm)
Assembly
(Leg 1,2,3 & 4)
M
H(8)
2.00
G(8)
T
P
(Base Swivel)
Plate
(1)
J
(8)
I
2.50
1.50
S
(Under Arm
Brace)
R
Arm
N
(Foot rest
1, 2, 3, & 4)
Item No: MHYA-DCC - S - R
HYANNIS COUNTER SWIVEL CHAIR
Assembly Instructions
Item No: MHYA-DCB - S - R
HYANNIS BAR SWIVEL CHAIR
Do not use
any hand drill
on this product
ALLEN WRENCH
( included )
You will also need a phillips-head screwdriver
( not included )
WRENCH
( not included )

Right side
Front Leg (FR)
(identification marks
facing up)
K
Under Arm
brace
G
FRONT
Right side
Rear Leg (RR)
(identification
marks
facing up)
K
1a - Attach part ( S ) under arm brace to part ( K ) front right side ( FR ) & Rear right side ( RR ) legs using 4 of screws.
( G ) 2 for each leg. Tighten screws using a phillips-head screwdriver. Be sure to lay the legs and arm brace on
a flat clean surface to assemble. Line up the front right leg ( FR ) with the front of the arm brace ( 2 screws ),
line up the rear right side leg ( RR ) with the back of the arm brace (1 screw). Make sure the identification marks
FR & RR are facing upward. Follow the same instructions for left side legs ( L ), the identification marks FL & RL
should be facing down. Leg and arm brace assembly should form an "A" frame if done correctly.
1b - To Attach part ( K ) , Right leg Assembly to part ( R ) arm, lay arm face down on a flat clean surface, place ( K )
right side leg assembly over the arm using ( 6 ) of screw ( A ) tighten screws using a phillips-head screwdriver.
Follow the same instructions for left side legs ( L ).
FR
RR
FR
RR
S
Right side
Rear Leg (RR)
(identification marks
facing up)
K
Right side
Front Leg (FR)
(identification marks
facing up)
K
Figure 1
Left side
Front Leg (FL)
(identification marks
facing down)
L
Under Arm
brace
G
FRONT
S
L
Left side
Rear Leg (RL)
(identification marks
facing down)
Left side
Rear Leg (RR)
(identification marks
facing down)
Under Arm
brace
FRONT
Left side
Front Leg (FR)
(identification
marks
facing down)
BACK
Arm
1b
1a
A
Under Arm
brace
FRONT
S
BACK
Arm
R
L
L
S
A
R

2,b - Attach part ( Q ) , seat back assembly , to part ( J ),
seat bottom assembly , as shown in Figure 2
see detail 2 using ( 4 ) of screws ( A ) , 2 on each side,
tighten screws using a phillips-head screwdriver .
Figure 2
A
( Detail 2 )
( Detail 1 )
2,a - To Attach part ( Q ) , seat back assembly , to part ( J ),
seat bottom assembly as shown, you must align the
lower front edge of yoke to the front edge of groove,
see detail 1 .
Front edge of groove
Front edge of yoke
( Seat Bottom Assembly )
( Seat Back Assembly )
Figure 3
Q
3,a - Attach part ( K ) , right side front and rear leg assembly , to assembly from
Figure 2 as shown in Figure 3, make sure identification marks ( FR ) and ( RR ) are
facing inside towards the seat see detail 3, using ( 2 ) of joint connector bolts ( B ),
( 2 ) washer ( C ), ( 2 ) lock washer ( D ), ( 2 ) hex nut ( E ), see detail 4
tighten bolts using an allen wrench and also an adjustable wrench. Follow
the same instructions for left side front and rear leg assembly.
3,b - Attach part ( K ), right arm leg assembly, to seat back assembly ( Q ), as shown in
Figure 3, see detail 5, using ( 3 ) of lag screws ( F ), tighten screws using and allen
wrench. Follow the same instructions for left side front and rear leg assembly.
B
C
D
E
( Detail 4 )
F
F
( Detail 5 )
B
F
K
identification marks
(Right side
Front & Rear leg) (FR) (RR)
( Detail 3 )
( Seat Back
Assembly )
Q
T

Figure 4
4 - Attach part ( M ) , Leg 1 , to part ( P ), base swivel plate, as shown in Figure 4, see detail 6, using ( 2 ) of lag screws
( H), tighten screws using an allen wrench .
P
(Base swivel
Plate)
M
( Detail 6 )
H
5 - Attach part ( N ) , Foot rest 1, to assembly from figure 4 as shown in Figure 5, see detail 7, using ( 1 ) of screws ( I ),
tighten screw using a phillips-head screwdriver.
Figure 5
I
( Detail 7 )
align dowel pins to holes
and press fit to leg
6 - Attach part ( M ) , Leg 2, to assembly as shown in Figure 6, see detail 8 and detail 9
(detail 8) - using ( 1 ) of screws ( I ), tighten screw using a phillips-head screwdriver.
(detail 9) - using ( 2 ) of lag screws ( H ), tighten screws using an allen wrench.
Figure 6
(Leg 1)
(Leg 2)
M
H
( Detail 8 )
( Detail 9 )
Figure 7
7 - Attach part ( N ) , Foot rest 2, to assembly from figure 6 as shown in Figure 7, see detail 10 .
(detail 10) - using ( 1 ) of screws ( I ), tighten screw using a phillips-head screwdriver.
( Detail 10 )
(Footrest 2 )
N
N
(Footrest 1)
I
I

Figure 8
8 - Attach part ( M ) , l eg 3, to assembly from figure 7 as shown in Figure 8, see detail 11 and detail 12.
(detail 11) - using ( 1 ) of screws ( I ), tighten screw using a phillips-head screwdriver.
(detail 12 ) - using ( 2 ) of lag screws ( H ), tighten screws using an allen wrench.
(Leg 3)
M
( Detail 11 )
( Detail 12 )
H
10 - Attach assembly from figure 10, to assembly from figure 8 ,
as shown in Figure 10, see detail 14 and detail 15.
(detail 14) - using ( 2 ) of screws ( I ), tighten
screw using a phillips-head screwdriver.
(detail 15) - using ( 2 ) of lag screws ( H ),
tighten screws using an allen wrench.
( Detail 15 )
( Detail 14 )
I
Please contact one of our Product Specialists for assembly assistance or questions at 1-866-947-7632 or email [email protected].
Specialists are available weekdays 8:30 a.m. to 4:30 p.m. EST
CARE AND MAINTENANCE
To clean Your product, use mild soap and water. For heavy soil build-ups use any Non-Abrasive household cleaners.
( Detail 16 )
11 - Attach assembly from figure 3, to assembly from figure 10, as
shown in Figure 11, see detail 16. Using grease tube (I) provided,
lubricate both the metal stem and the inside of the nylon sleeve
and then locate on center of base and press down.
I
H
9 - Attach parts ( N ) , foot rest 3 & 4, to part (M), leg 4 as
shown in Figure 9, see detail 13 .
(detail 13) - using ( 2 ) of screws ( I ), tighten screw
using a phillips-head screwdriver.
(Footrest 3 & 4 )
( Detail 13 )
N
(Leg 4)
M
I
Figure 9
Figure 10
Figure 11