Mandik CP-M-B User manual

KJM MANDÍK Controlling with CPM Wall-Mounted Control
NONO_CP-M-B_2019-6 www.mandik.cz
2
Table of Contents
1 Introduction .......................................................................................... 3
2 Technical Data ...................................................................................... 4
3 Dimensions ........................................................................................... 4
4 Electrical Wiring ................................................................................... 5
5 Installation ............................................................................................ 6
6 Configuration of Climatix Controller .................................................. 6
7 Operation of Wall-Mounted Control ................................................... 7
8 Maintenance ......................................................................................... 9
9 Waste Disposal .................................................................................... 9

KJM MANDÍK Controlling with CPM Wall-Mounted Control
NONO_CP-M-B_2019-6 www.mandik.cz
3
1 Introduction
CP-M-B is a wall-mounted controller for Mandík air-conditioning units with the
following parameters:
 Remote control of a Mandík air-conditioning unit
 For use with controllers Climatix POL6xx and POL4xx
 1 rotary knob for setting the desired room temperature
 1 rotary knob for switching on the air conditioner and setting the fan speed
 1 LED for displaying modes
 1 LED for displaying faults
 Power supply of 24 V ss.
 Mounting on KU68 installation box
 Valid from the software version of controller KJVVS103625.01

KJM MANDÍK Controlling with CPM Wall-Mounted Control
NONO_CP-M-B_2019-6 www.mandik.cz
4
2 Technical Data
3 Dimensions
Parameter Value Unit
Power supply voltage 14 – 24 V DC
Maximum consumption 0.4 W
Power supply for LEDs 14 - 24 V DC
Input load capacity min 100 kΩ
Conductor cross-section 0.6 to 0.8 mm2
Recommended cable J-Y(ST)Y 4x2x0.8
Operating humidity 0 - 90 % RH
Operating temperature 0 to +50 °C
Storage temperature -20 to +60 °C
Protection IP20
Dimensions 120x80x40 mm

KJM MANDÍK Controlling with CPM Wall-Mounted Control
NONO_CP-M-B_2019-6 www.mandik.cz
5
4 Electrical Wiring
Terminal Descripti
on
Type Meaning
1
ERROR
Input
Power
supply
for
fault signalling
LED
+24
V ss.
2 RUN Input Power supply for run signalling LED +24 V ss.
3
FAN
Output
Fan switching on and required speed
0
-
10
V
4
TEMP
Output
Desired temperature correction
0
-
10
V
5 +24V Power
supply
Power supply +24 V ss.
6 GND Power
supply
Common ground
The CP-M-B series wall-mounted control can only be powered from a DC power
supply. The power supply must meet the requirements given in chapter ‘2
Technical data’.
Connection
of terminals
Note
Terminal
side

KJM MANDÍK Controlling with CPM Wall-Mounted Control
NONO_CP-M-B_2019-6 www.mandik.cz
6
5 Installation
The CP-M-B series wall-mounted control is designed for installation in indoor,
dry environments. It should be placed about 1.5 m above the floor at a place
with good natural air circulation. The unit is suitable for mounting on most
commercially available wiring boxes or directly on a wall.
When mounting the unit, the mounting plate must be fixed first. When the
electrical contacts are connected, the top panel is hung on the mounting plate
and clicked in place.
On the underside of the front cover there are two rectangular holes for a small
flat-blade screwdriver. Insert a screwdriver into each hole to release the inner
latches and to lift the front cover and then to take it off easily. Both the covers
are plastic.
The unit may only be opened by a qualified electrician.
Electrical installation must be performed in accordance with the relevant
regulations and standards.
Connected cables must meet the insulation requirements of the mains voltage.
Caution! The unit is not protected against accidental connection to ~ 230
V.
6 Configuration of Climatix Controller
The Climatix controller must be correctly configured for Mandík air-conditioning
unit to operate correctly with a wall-mounted control. Configuration is performed
at the factory based on customer requirements and an electrical diagram that is
part of the documentation supplied with a specific order. General configuration
steps are as follows:
- Selection, setting and assignment of an input for monitoring the desired
temperature.
- Selection, setting and assignment of an input for monitoring the desired
speed.
- Selection and assignment of an output for signalling unit operation.
- Selection and assignment of an output for signalling unit fault.
- Setting the temperature change range.
- Setting the desired speed change range.
- Selection of Comfort or Attenuation mode when the unit is on.
- Selection of Off or Tempering mode when the unit is off.
Prior configuring the Climatix controller, it is necessary to familiarize yourself
with the manual ‘Measurement and control system for MANDÍK air-conditioning
units - Detailed instructions and control’.
Installation
Opening
the cover
Installation
principles
Note
Configuration
of Climatix
controller
Note

KJM MANDÍK Controlling with CPM Wall-Mounted Control
NONO_CP-M-B_2019-6 www.mandik.cz
7
7 Operation of Wall-Mounted Control
The wall-mounted control allows:
 Switching on/off and controlling the fan speed.
 Correction of the desired temperature.
 Air-conditioning unit status indication.
The rotation knob for controlling the fan speed on the control (position C) has
two functions:
 Switching the air-conditioning unit on/off.
 Controlling fan speed.
Position
Meaning
OFF The air-conditioning unit is off. It switches on when the knob is at least
in the
MIN
position
.
MIN The air-conditioning unit starts on and the fans start to run at the
minimum speed. The minimum speed values are set separately for
each fan in the menu on the controller display Components  Fans 
Inlet  Attenuation and Components  Fans  Outlet 
Atte
nuation
.
MAX The fans are running at maximum speed. The maximum speed values
are set separately for each fan in the menu on the controller display
Components  Fans  Inlet  Comfort and Components  Fans

Outlet

C
omfort.
MIN-MAX The fan speed changes continuously according to the rotary knob
position from
MIN
t
o
MAX
.
Legend
Po
sition
Meaning
A Green LED for mode indication.
B
Red LED for fault signalling
.
C Rotary knob for switching on fans and setting their speed.
D Rotary knob for correcting the desired temperature.
Switching
on and
speed
control
A
D
C
B

KJM MANDÍK Controlling with CPM Wall-Mounted Control
NONO_CP-M-B_2019-6 www.mandik.cz
8
.
The desired temperature correction value can be changed using the rotary knob
on the control - position D. The rotary knob corrects the desired temperature
from the nominal temperature. The nominal temperature is set for each
Comfort or Attenuation mode in menu Components  Temperature
Control. The minimum and maximum correction is set in menu Input/Output
Assignment  External Switches  Desired Temperature Min Max. The
standard setting for Min and Max is 5 °C.
The status of the air-conditioning unit is indicated by the Run (position A) and
Fault (position B) LEDs.
St
atus
Meaning
OFF The unit is switched off.
Flashing with
a period of 1
sec.
The unit is in the Start auxiliary mode, which is preparing the unit to
start the fans.
ON The unit is started by the fan speed control knob position and the
Start
auxiliary mode has
ended.
Flashing with
a period of 3
sec.
The unit has started automatically based on the assessed need for
frost protection or room ventilation and the Start auxiliary mode has
ended. When the conditions that caused the unit to start up are met,
the unit switches itself off. This status only occurs if the speed control
knob is in the OFF position and the Climatix controller is preset to the
Tempering
mode
.
Sta
tus
Meaning
OFF No fault has occurred.
Flashing Indicates that a new fault has occurred.
ON Indicates a fault that persists after acknowledgment by the
operator.
The LED functions described above are standard ones and can be customized
according to client requirements.
Desired
temperature
c
or
rection
Unit status
Run LED
Fault LED
Note

KJM MANDÍK Controlling with CPM Wall-Mounted Control
NONO_CP-M-B_2019-6 www.mandik.cz
9
8 Maintenance
The unit requires no regular inspection or maintenance.
Depending on how the unit is used, dust must be removed from the unit’s
internal electronics from time to time. The unit is cleaned with a dry painting
brush or soft brush or vacuum cleaner when it is off and disassembled.
The specified maintenance may only be performed by the manufacturer or
an authorized service organization!
9 Waste Disposal
The disposal of the unit is governed by regulations on the management of
electrical waste. The device must not be disposed of with normal household
waste. It must be handed over at designated facilities and recycled.
Cleaning
Note
Disposal of
electronics

The producer reserves the right for innovations of the product. For actual product information see
www.mandik.com
MANDÍK, a.s.
Dobříšská 550
26724 Hostomice
Czech Republic
Tel.: [phone]
E-Mail: [email protected]
www.mandik.com