M&s systems Mc702 User manual

MC702

MUSICAL INTERCOM SYSTEM

OWNER'S GUIDE

S A F E T Y INSTRUCTIO

CONGRATULATIONS

Your purchase of an M&S built-in musical intercom system is an investment

that will provide years of service and convenience. M&S built-in music systems

are backed with more than 50 years of experience in the design and

NS ........................................................... 3

ABOUT YOUR SYSTEM ......................................... 4

SETUP ....................................................... 5

Settingthetime .......................................... 5

SettingAutomaticon/offtime ................................ 5

Settingtheautoonvolumelevel ............................. 6

RemoteIntercomStationSelection ........................... 7

Settingtheintercomlevel................................... 7

Settingupthewirelessremotecontrol......................... 8

MUSICOPERATION ............................................ 9

Controls ................................................ 9

Operating the tuner ...................................... 10

UsingMemoryPresets .......................................... 10

Storing radio station frequencies ............................ 10

Recalling radio station frequencies .......................... 10

Operating a tape or CD player ............................. 11

Adjustingmusicvolume ................................... 11

INTERCOMOPERATION........................................ 12

Communicatingwithotherrooms ........................... 12

Monitoringotherrooms ................................... 13

Communicating with door locations .......................... 13

TROUBLESHOOTING .......................................... 14

Problem-Whattocheck .................................. 14

Manual reset procedure ................................... 14

CAREANDMAINTENANCE ..................................... 15

NOTES ...................................................... 15

WARRANTY .................................................. 15

Read instructions - All the

safety and operating

instructions should be read

before the appliance is

operated.

Retain instructions - The

safety and operating

instructions should be

retained for future reference.

Heed warnings - All warnings

on the appliance and in the

operating instructions should

be adhered to.

Follow instructions - All

operating and use instructions

should be followed.

Water and moisture -

The appliance should

not be used near water

- for example; near

bathtub, washbowl,

kitchen sink, laundry

tub, in a wet basement,

or near a swimming

pool, and the like.

Attachments - Do not

use attachments not

recommended by the

product manufacture as

they may cause

hazards.

Ventilation - The appliance

should be situated so that its

location or position does not

interfere with its proper

ventilation. For example, the

appliance should not be

situated on a bed, sofa, rug,

or similar surface that may

block the ventilation

openings: or, placed in a

built-in installation, such as a

bookcase or cabinet that may

impede the flow of air to the

ventilation openings.

Heat - The appliance should

be situated away from heat

sources such as radiators,

heat registers, stoves, or

other appliances (including

amplifiers) that produce heat.

Power sources - The

appliance should be

connected to a power supply

only of the type described in

the operating instructions or

as marked on the appliance.

Grounding or polarization -

Precautions should be taken

so that the grounding or

polarization means of an

appliance is not defeated.

Power lines - An outdoor

antenna should be located

away from power lines.

Outdoor antenna grounding -

If an outside antenna is

connected to the receiver, be

sure the antenna system is

grounded so as to provide

some protection against

voltage surges and built up

static charges. Section 810

of the National Electrical

Code, ANSI/NFPA No.

70-1984, provides information

with respect to proper

grounding of the mast and

supporting structure,

grounding of the lead-in wire

to an antenna discharge unit,

size of grounding conductors,

location of antenna discharge

unit, connection to grounding

electrodes, and requirements

for the grounding electrode.

See Figure below.

Object and liquid entry -

Never push objects of

any kind into this

product through

openings as they may

touch dangerous

voltage points or

short-out parts that

could result in a fire or

electric shock. Never

spill liquid of any kind

on the product.

Servicing - The user

should not attempt to

service the appliance

beyond that described in the

operating instructions. All

other servicing should be

referred to qualified service

personnel.

Damage requiring service -

The appliance should be

serviced by qualified service

personnel when:

The power-supply

SAFETY INSTRUCTIONS

The exclamation point within an

equilateral triangle is intended

to alert the user to the presence

of important operating and

The lightning flash with

arrowhead symbol within an

equilateral triangle is intended to

alert the user to the presence of

ABOUT YOUR SYSTEM

Your new Model MC702 is a state of the art stereo music and intercom system that

provides music and room to room communication throughout your house. An

optional door chime can be integrated into the system to provide door

communication with automatic muting. The MC702 contains a digital clock with

backup power source that maintains the correct time for up to 3 hours without

power and never needs replacing.

The innovative transflective LCD display and power-conserving back light can be

read in any lighting condition from direct sunlight to complete darkness. The unit

provides music for up to 15 rooms with plenty of power. The MC702 has a digital

phase lock loop tuner with 8 AM and 8 FM station presets. It also has two external

source inputs (AUX IN and TAPE IN) and one line output (TAPE OUT) that can be

used with M&S's built-in cassette tape and/or CD player, as well as your TV or

other music sources. The MC702 enables communication between up to 15

rooms and the master location plus up to 4 door entry locations.

The MC702 can turn itself ON and OFF at preset times like an alarm clock or

sleep-to-music device. As a home security device, it can be programmed to play

talk radio when the house is vacant. The MC702 was designed to be as user-

friendly as possible the display tells you how to set the time and alarm functions.

It also shows when and how the intercom function is being used. It has a built-in

door release which can be used to open a door or gate from the master unit or

from any indoor remote room station.

The MC702 has an optional hand-held RF REMOTE CONTROL which allows you

to turn the radio on or off, scan radio stations up or down, change sources, and

change the volume up or down from ANYWHERE in or around the house.

The MC702 allows you to monitor any room (including the master unit location) to

let you know when a baby is crying or when an elderly person needs help.

Like all M&S products, the MC702 is designed to make your home atmosphere

more enjoyable. M&S is committed to producing high quality products for your

home. If you have any questions about the operation of your system, please call

us at

(800) 366-9422.

SETUP

Note: The MC702 remains in the set mode for 25 seconds with no activity

(no buttons being pressed) after which the unit automatically returns

to the normal mode of operation. The TIME SET button must be

pressed again to return to the set mode.

SETTING THE TIME

When the Time/Auto Set button is

pressed momentarily, the display

will show SET TIME and the current

time will be displayed with the hours

flashing. The UP and DOWN

buttons (either TUNING UP and

DOWN or VOLUME UP and

DOWN) can then be used to

increment or decrement the current

time hours. Pressing the UP button

(or DOWN button) momentarily will

increment (or decrement) the hours

by one each time the key is pressed. Holding the UP button (or DOWN button)

depressed will rapidly increment (or decrement) the hours until the button is

released. The time display also includes the AM or PM indicator that is changed

by scrolling the hours past 12:00.

Once the current hours have been set correctly, momentarily press the

TIME/AUTO SET button again. The display will show SET TIME and the current

time will be shown with the minutes flashing. The UP and DOWN buttons can be

used as described previously to increment or decrement the current time minutes.

Once the current minutes have been set correctly, momentarily press the

TIME/AUTO SET button again to

return to the normal mode or let the

MC702 automatically return to the

normal mode if no buttons are

pressed for 25 seconds.

SETTING AUTOMATIC ON/OFF TIME

To set the AUTO on and off times,

the TIME/AUTO SET button must

be momentarily pressed three times

without changing the current time. After pressing the TIME/AUTO SET button for

the third time, the display will show SET AUTO ON TIME and the auto on time will

be displayed with the hours flashing. The UP and DOWN buttons can be used as

previously described to increment or decrement the auto on time hours.

Once the AUTO ON TIME hours has been set correctly, momentarily press the

TIME SET button again. The display will show SET AUTO ON TIME and the

AUTO ON TIME will be displayed with the minutes flashing. The UP and DOWN

buttons can be used as previously described to increment or decrement the AUTO

ON TIME minutes.

Once the AUTO ON TIME minutes has been set correctly, momentarily press the

button again. The display will show SET AUTO OFF TIME and the AUTO OFF

TIME will be displayed with the hours flashing. The UP and DOWN buttons can

be used as previously described to increment or decrement the AUTO OFF TIME

hours.

Once the AUTO OFF TIME hours has been set correctly, momentarily press the

TIME SET again. The display will show SET AUTO OFF TIME and the AUTO

OFF TIME will be displayed with the minutes flashing. The UP and DOWN buttons

can be used as described previously to increment or decrement the AUTO OFF

TIME minutes.

SETTING THE AUTO ON VOLUME LEVEL

When the Auto function is turned

on, the MC702 will turn itself on

automatically when the current time

reaches the Automatic ON TIME

and will then turn itself OFF when

the current time reaches the

Automatic OFF TIME. When the

MC702 automatically turns itself

ON it will always turn on at the

same volume level. This "AUTO

ON VOLUME LEVEL" has a default

of 12 but it can be changed

following these simple steps:

ìTurn on the MC702 by momentarily depressing the POWER button (unless the

radio is already on).

íMomentarily press the VOLUME UP and AUTO buttons, at the same time, and

then release. The display will show the letter 'A' for AUTO ON volume followed

by the current music volume setting.

îDepress the VOLUME UP or VOLUME DOWN buttons to set the desired

music volume level. (1-32).

NOTE: The MC702's AUTO ON volume is defaulted to the last volume setting

when the music was last turned off. Therefore, it is recommended that

a new fixed auto volume setting be set since the MCTX wireless

remote control transmitter, effectively, turns off the radio when the

volume is turned down completely. If the music is turned off using the

MCTX wireless transmitter the music will AUTO ON at a volume level

of 1.

ïWhen you have the volume set to your desired level wait for 9 seconds. The

display will revert to the time display.

Step 1 - Push in

to release

Step 2 -

Release to

open

Step 3 - Open

REMOTE INTERCOM STATION SELECTION

These switches are used to control the operation of the room

station in each corresponding room. The MASTER

INTERCOM switch controls the master room station. ROOM

SELECTOR switches 1 through 9 control the corresponding

remote room stations. The PATIO SELECTOR switch controls

patio room station(s).

There are four positions

for each of these

switches:

INTERCOM- A room station with its switch set in the

INTERCOM position will only hear intercom

(excluding monitor) and the chime.

RAD/INT - A room station with its switch set in the ON

position will hear intercom communications,

music and chime.

OFF - A room station with its switch set in the OFF position

will not hear anything, but can still talk to other room

stations and the door.

MONITOR A room station with its switch set in the MONITOR

position will not hear any intercom

communications, but the room station will be used

as a microphone. Any sounds that this microphone picks up will be

heard from any room station that is in the ON position. The

MONITOR position can be used to listen to (monitor) a baby's or

elderly person's room.

Your MC702 may be equipped with either a 3-note or 8-note Door Chime. This

optional chime always mutes the radio and rings through the master speaker when

the doorbell button is pressed. It also rings through all the room stations that are

turned on. However, the music speakers mute while the chime is broadcast

through the room stations and the master unit.

SETTING THE INTERCOM LEVEL

The INTERCOM LEVEL adjust the gain of the entire intercom system. The

INTERCOM LEVEL is generally set by the installer upon initial installation to match

your home's acoustics and should not require further adjustment. However, if you

find the system's intercom gain is too high or too low, follow the procedure below

to reestablish the correct intercom gain setting.

ìTurn all room station volume controls to maximum (fully-clockwise). Turn the

master speaker volume to maximum (fully-clockwise). Set all PRIVACY

switches to the OFF or out position (N75/N78 only).

NOTE: Your MC702 system is designed for high intercom gain and very low

noise simultaneously. When monitoring room stations, it is not necessary

to increase the intercom level in an effort to hear 'something'. Doing so

will unnecessarily increase any background noise, such as air

conditioning systems and other appliances built-in to your home. If you

are monitoring a baby's room, for example, no noise will be heard until

the baby cries or makes a noises at which time you will hear with ample

volume.

Steady SAVE (Release

transmitter button)

Press and

hold the

TUNING UP

button to

signal the

MC702

wireless

receiver

Flash between TEST &

SAVE

íDepress and hold ROOM TALK at the master location while speaking.

îAdjust the INTERCOM LEVEL until good clear audio is heard at the remote

stations without hearing acoustic feedback (squeal). This initial setting should

result in audio that is likely to be as loud as you would normally need. This

setting should not be readjusted. The volume controls at the individual room

stations can be adjusted as desired for that room.

SETTING UP THE WIRELESS REMOTE CONTROL

PROGRAMMING - Upon initial

power up of the MC702 or upon

applying power after the unit loses its

memory (power outages greater than 2

hours), the unit must be programmed

or taught the unique code that is

present in the REMOTE CONTROL

TRANSMITTER. To do this, the

MC702 must be put into its test mode

by momentarily pressing the VOLUME

UP and SOURCE buttons at the same

time on the MC702. The display on the MC702 should show TEST.

While the MC702 is in the

test mode, press and hold

the TUNING UP button on

the REMOTE CONTROL

TRANSMITTER. The

display on the MC702 will

flash between TEST and

SAVE. When the display

shows SAVE without flashing, release the button on the

transmitter. The MC702 has now learned the

TRANSMITTER. Momentarily press both VOLUME UP and

POWER buttons at the same time to restore the MC702 to

normal operating mode.

If more than one transmitter is to be used with the system,

the second, third, and fourth transmitters must be learned by

pressing the TUNING DOWN, VOL UP, and VOL DOWN on

Exiting TEST mode or 'RESETTING' the

MC702

NOTE: Pressing the same button on two different

transmitters will automatically overwrite the

previous transmitter stored in memory. Always

MUSIC OPERATION

the respectively instead of the TUNING UP button on the TRANSMITTER.

To exit the TEST mode, press the

VOLUME UP and POWER buttons at

the same time and then release.

CONTROLS

LCD DISPLAY - This back lighted1

readout indicates: current time,

auto radio on/off status, radio

station frequency, station memory

setting, and active intercom status.

This display also shows diagnostic

codes when the TEST mode is

enabled.

UP/DOWN BUTTONS - These

buttons are used to scan through

FM or AM radio stations.

1, 2, 3, and 4 BUTTONS - These

NOTE: The VOLUME UP/DOWN, TUNING UP/DOWN and SOURCE select

buttons are duplicated on the wireless remote control transmitters.

buttons are used to save and

recall your most frequently used

FM and AM radio stations.

VOLUME UP/DOWN BUTTONS -

These buttons are used to

increase and decrease the overall

system radio volume.

POWER ON/OFF BUTTON - This

button is used to turn the MC702

music source ON and OFF. Note:

The intercom is always on!

AUTO button - This button is used

to turn the Automatic Music (AUTO

*) function ON and OFF.

TIME/AUTO SET BUTTON - This

button is used to access the time

setting mode.

SOURCE button - This button is

used to select the audio source

(FM A, FM B, AM A, AM B, AUX

input, or TAPE input).

OPERATING THE TUNER

To listen to broadcast stations, press the POWER button. Notice the display will

change from the time to station frequency. Pressing the SOURCE select button will

allow you to change from FM, AM, TAPE and AUX respectively. The SOURCE

button is available on the MCTX wireless remote control transmitter.

AUTO SCAN When any AM or

FM band is chosen, momentarily

pressing the TUNING UP and

TUNING DOWN buttons will

change the tuned station frequency

to the next local station. The audio

will be muted and the display will

show radio station frequencies

increasing or decreasing as it

scans. When the next local radio

station is detected, audio will again

be heard.

MANUAL SCAN Pressing and holding either the TUNING UP or TUNING

DOWN button will cause the tuner to scan each successive frequencies one at a

time whether a radio station is broadcasting on that frequency or not. You will also

be able to hear the reception at these frequencies as they are scanned. When the

desired radio station is tuned, release the TUNING UP or TUNING DOWN button

to stop the manual scan function. Manual scanning is useful for reception of distant

stations that would not otherwise be tuned with the auto scan feature. The MC702

automatically switches from stereo to mono to allow greater sensitivity for a distant

radio station. NOTE: To scan upward or downward by just one frequency, the

TUNING UP/DOWN button should be depressed until the frequency changes--then

immediately released.

USING MEMORY PRESETS

Storing radio station frequencies

Change to the desired radio band

(FM1, FM2, AM1 or AM2), using

the source button.

Tune to the desired radio station.

Press and hold a numbered button

until the preset number is

displayed.

Example: Save a radio station in band

FM2, preset 3.

Press the SOURCE button to

change to FM2.

Tune to the desired radio station.2

Hold the 3 button until a 3 appears

as the preset number.

Recalling radio station frequencies

Change to the desired radio band,

using the SOURCE button.

Momentarily press the desired

numbered preset button.

Example: Recall the radio station saved

in band AM1, preset 2.

Press the SOURCE button to

change to AM1.

Momentarily press the 2 button.

OPERATING A TAPE OR CD PLAYER

The MC702 features two

source inputs to connect a

variety of built-in and

external music sources such

as Laser disc players, CD

players and tape players. The

different sources connected

to the TAPE and AUXILIARY

inputs are selectable by

pressing the SOURCE select

button once the POWER is

turned on. Momentarily

depressing the SOURCE

button changes the music

source from FM, AM, AUX and TAPE inputs, respectively. The SOURCE button

on the MCTX wireless remote control performs the same function as the SOURCE

select button on the MC702. NOTE: The SOURCE button is only active when the

power is on. NOTE: IF the MC702 is installed with the MCD6 multidisc CD

changer, the TUNING UP/DOWN buttons on the MCTX wireless remote control

transmitter will operate the track selection when AUX mode is selected on the

MC702.

ADJUSTING MUSIC VOLUME

CAUTION: Take care not to overdrive the amplifier by using excessive

system volume to overcome the low volume settings on the

music speakers. Doing so will result in distorted audio and may

cause amplifier failure!

There are two ways to

adjust music volume.

The MC702 system

volume control adjusts

the music volume for all

music speakers in the

house and shows the

volume setting on the

display. (1 = lowest

volume and 32 = highest

volume) Depressing and

holding the VOLUME

UP or VOLUME DOWN

button steadily

increases or decreases,

respectively, the system volume. Momentarily depressing the VOLUME UP or

VOLUME DOWN increases or decreases, respectively, the system volume by one

level. Each speaker in the house has a volume control to adjust the output at the

speaker itself. Normally, the individual speaker volume controls are set to

maximum or near maximum settings.

INTERCOM OPERATION

ROOM TALK function (all call)

COMMUNICATING WITH OTHER ROOMS

The MC702 system with it's N75, N75RS, and NRC75 series speakers are

designed for whole house communication and ease of use. To talk to the room

station depress the ROOM TALK button while speaking. To hear the response

depress the ROOM LISTEN button. It is not necessary for the called party to press

ROOM TALK to reply. Therefore, this type of hands-free communication is

beneficial when communicating with someone who is unable to reach the controls

of room station to reply. If you are receiving a call from someone else, and are at

a non-RS room station that has the PRIVACY feature enabled, you must either

turn off the PRIVACY feature or press ROOM TALK to respond. When performing

a ROOM TALK function, audio will be heard only at the stations that are turned on

at the master and have their volume controls set above the minimum (counter-

clockwise) setting. Stations that are set to the OFF or MONITOR position at the

master will not hear the ROOM TALK call nor will they be heard in the ROOM

LISTEN mode.

ROOM LISTEN function (all listen)

Monitoring rooms

MONITORING OTHER ROOMS

Room station monitoring is useful for constant monitoring of small children and

those requiring special care. Any station in which you wish to monitor should be

set to the MONITOR position on the room switch panel. The result of the combined

monitored stations will be broadcast to any station set to ON at the room switch

panel. Non-RS room stations that have the PRIVACY feature enabled cannot be

monitored regardless of the room switch setting at the room switch panel. The

MC702 is designed to prevent the door chime from ringing at stations set to the

MONITOR position at the room switch panel. This will prevent disturbing the

occupants of the monitored rooms.

COMMUNICATING WITH DOOR LOCATIONS

The MC702 features two way intercom to the door locations. With the MC702 you

need not risk unwanted intrusion by opening the door to respond to the door bell.

To communicate with the visitor, depress both ROOM TALK and ROOM LISTEN

buttons and speak. To hear the response from the visitor, simply release BOTH

buttons. This will automatically switch the system to DOOR LISTEN mode.

Pressing both ROOM TALK and ROOM LISTEN again allows you to again talk to

the visitor. The DOOR LISTEN function will automatically time out in about 20

seconds or when you momentarily depress ROOM LISTEN or ROOM LISTEN by

itself.

Talking to the door stations Listening to the door stations

TROUBLESHOOTING

M&S Systems products are designed for years of reliable service. If you encounter

any problems with your system review this operating guide again. Your installer

or dealer can charge you for a service call to come to your home and show you

how to operate your system. Most problems are caused by incorrect setup,

improper adjustment and incorrect operation and can be corrected by following the

instructions in this operating guide. The table below should assist in

troubleshooting your problem. If after reviewing this operating guide and are

unable to resolve the problem contact your installer/dealer or technical service at

(800) 366-9422.

PROBLEM WHAT TO CHECKProblem - What to check

System squeals when

ROOM TALK or ROOM

LISTEN is depressed

INTERCOM level is set too high at the master

location. Reduce the INTERCOM level.

Radio turns on by itself Check for AUTO operation. If the display shows

'AUTO', turn off the AUTO feature. If the AUTO

feature is being enabled inadvertently, program a

more suitable AUTO ON/AUTO OFF to prevent

being disturbed by AUTO ON activation.

Can't get more than one

wireless remote control

transmitter to work.

The working transmitter's identification has

overwritten the other transmitters. Reprogram all

transmitters making sure to depress a different

button on each transmitter. (see 'Setting up the

MCTX wireless remote control')

Check batteries - replace batteries if necessary

Cannot monitor rooms Check the monitored room stations and ensure

that the PRIVACY switches are off and the

volume controls are turned up (clockwise).

Resetting the MC702

Display shows TALK or

LIST without any buttons

depressed

Shorted cable or bad speaker. Turn off room

speaker switches to isolate which remote station

run is causing the problem. Contact

dealer/installer.

MANUAL RESET PROCEDURE

In some cases, performing a reset on the MC702 may resolve your problem. First

try resetting the MC702 by pressing the POWER and VOLUME UP buttons at the

same time.

CARE AND MAINTENANCE

Please record the following information for future reference:

Installer Date of

installation

Model MC702 Serial number

(Serial number is located behind the face panel insert on the MC702)

NOTES

WARRANTY

No maintenance is required to provide reliable operation. The MC702 can be

cleaned using a slightly dampened cloth. No chemicals should be used to clean

the face panel components. Many common household chemicals may damage or

discolor the face panel components. Use care when cleaning the display window.

M&S SYSTEMS Limited 2-Year No-Fault Product Warranty

M&S SYSTEMS warrants for 2 years all products to be free of defects (M&S SYSTEMS honors the 10-Year No-Fault warranty for AirVac Gold

power units. See section below). The warranty period begins from either (1) the date of “first user” purchase of this product or (2) the first close of

escrow date on a residence in which this new product was originally installed. This warranty extends to the original user of the product and to each

subsequent owner of the product during the term of this warranty. M&S SYSTEMS will repair or replace, at its option, parts and materials at no charge.

Parts supplied under this warranty may be new or rebuilt at the option of M&S SYSTEMS.

If, during the limited warranty period, it appears as though this product contains a defect which is covered by this limited warranty, call our toll free

service number before dismantling the product (1-800-877-6631). Remember to attain a Return Authorization Number (RAN) before

returning any product to M&S SYSTEMS. Send this product freight pre-paid and insured to our service center for warranty repair. You

will be advised on shipping instructions when you call the toll free service number. M&S SYSTEMS will return the repaired product freight pre-paid

within the U.S.A. The installing dealer or distributor may assist you, at your choice and expense, with returning product for repair. Please include a

brief description of the problem and a dated proof-of-purchase receipt with any product that is returned for warranty repair. ANY PRODUCT

RETURNED WITHOUT A RETURN AUTHORIZATION NUMBER WILL BE REFUSED.

THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, AND OF ANY OTHER

OBLIGATIONS OR LIABILITY ON THE SELLER’S PART. THIS LIMITED WARRANTY DOES NOT COVER DAMAGE CAUSED

BY IMPROPER INSTALLATION, THE VIOLATION OF APPLICABLE BUILDING OR ELECTRICAL CODES, OR THE USE OF NON-

M&S/NON-AIRVAC WIRE, CABLE OR WALL HOUSINGS. THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS

INSTALLED IN A PRIVATE RESIDENCE.

UNDER NO CIRCUMSTANCES SHALL THE SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES

ARISING IN CONNECTION WITH USE, OR INABILITY TO USE THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY,

FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, OR STRICT LIABILITY, EXCEED THE COST OF THE

PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION

WITH THE SALE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion maynot apply