Manhattan Comfort 4GMCC User manual

Stuck? Questions? We are here to help.
1-888-230-2225
[email protected]
1000009894 - 21/12/2021
Assembly Guide
Model: 4GMCC
Fortress 31.5" Mobile Garage Chest With Drawers

Do not place the parts directly onto the floor.
Use a cardboard sheet or a mat to place the
parts, during the separation and assembly.
In order to ease the assembly,
you should separate and identify the parts first
Necessary hardware for the assembly
Stuck? Questions? We are here to help.
1-888-230-2225
[email protected]
IMPORTANT
In order to avoid severe or even fatal injuries, follow the instructions carefully.
* Included in the kit * Not included in the kit
Locking nut, no key tightening required.

Hardware list
lb
Maximum weight
supported by
shelf and
drawer
WARNING
Fortress 31.5" Mobile Garage Chest With Drawers
F10
1000008352
F1
1000011853
Qty. 36
F2
1000011851
Qty. 36
F13
1000011850
Qty. 1 Qty. 2
F11
1000008354
Qty. 2
F17
1000008285
Qty. 1
F18
1000011849
Qty. 57
31lb
P15
Drawer Fund
P28
Drawer Front
P12
Drawer Right Side
P14
Drawer Back
P13
SideDrawer Left
Assembly Drawer
Assembly Drawer
P10
Upper Back
P7
Bottom
P5
Top
P9
Lower Back
P2
Right Side
P3
SideLeft
55lb
N º
D ESC R IPT ION GR EY C HA R C O A L M A T T E W HIT E
M A T ER I A L
M A TER I A L
M A T ER I A L
P2 RIGHT SIDE
3000007373 3000011884 3000011969 STEEL 1 UN
P3 LEFT SIDE
3000007377 3000011883 3000011968 STEEL 1 UN
P5 TOP 3000007369 3000011874 3000011960 STEEL 1 UN
P7 BOTTOM 3000008644 3000011882 3000011967 STEEL 1 UN
P9 LOWER BA CK 3000007266 3000011842 3000011930 STEEL 1 UN
P10 UP PER BA CK
3000007312 3000011846 3000011933 STEEL 1 UN
P12 DRAWER RIGHT SIDE
3000007360 3000011856 3000011943 STEEL 3 UN
P13 DRAWER LEFT SIDE
3000007337 3000011858 3000011945 STEEL 3 UN
P14 DRA WER BA CK 3000007365 3000011857 3000011953 STEEL 3 UN
P15 DRAWER FUND
3000007334 3000011869 3000011955 STEEL 3 UN
P28 DRA WER FRONT 3000007355 3000011861 3000011947 STEEL 3 UN
I D EN T I F Y TH E C OL OR OF YOU R C A B I N ET
QU A N TI TY

1 - Fit part P2 inside part P7
2 - Fit both parts in the frontal side, with F1 and F2.
1 - Fit part P7 inside part P3
2 - Fit both parts in the frontal side, with F1 and F2.
STEP 2
STEP 1
P7
P3
P5
P2
8x
F2
8x
F1
P7
P3
P2 P7
P3
P2
4x
F2
4x
F1
2
1
1
2
3
WARNING
Do not tighten
the screw
completely.
WARNING
Do not tighten
the screw
completely.

1 - Turn the cabinet with the back side
upwards.
2 - Fit parts P2 and P3 to parts P5 and P7 with
F1 and F2.
STEP 3
1 - Fit part P10 into parts P2, P3 and P5. Check that all fits are supported over the bolts.
2 - After fitting the parts, screw the bolts until locked.
STEP 4
8x
F2
8x
F1
P7
P2
P5
P3
180°
180°
P7
P2
P5
P3
1
2
P7
P2
P5
P10
P3
WARNING
Check that all parts are
correctly supported to
ensure product alignment.
WARNING
Position part P10
on the P5 side for
mounting the
cabinet.
WARNING
Do not tighten
the screw
completely.

1 - Fit part P9 into parts P2, P3 and P7. Check that all fits are supported over the bolts
2 - After fitting the parts, screw the bolts until locked.
STEP 5
STEP 6
1
2P7
P10
P9
P2
P3
2x
F10
2x
F11
16x
F2
16x
F1
P2
P5
P3
P7
3 - To assembly the cabinet with caster, align
the F10 and F11 to the holes in part P7
and fix them with F1 and F2.
4 - WARNING: Casters with lock (F11) must be
fitted in the frontal side of the cabinet.
WARNING
FLAT SURFACE
After tightening the screws,
make sure the cabinet does
not appear to be misaligned.
1 - Put the cabinet a flat surface.
2 - Completely tighten all screws.

4x
F18
STEP 7
6x
F18
STEP 8
1 - Fit part P15 to part P28.
2 - Screw the two parts with F18.
1 - Align parts P12 and P13 to part P15, until it leans against piece P28.
2 - Screw the two with F18.
P15
P28
P13
P15
P28
P12

9x
F18
1 - Insert part P14 over part P15 and between parts P12 and P13
2 - Then, fix part P14 to parts P12, P13 and P15, with F18.
STEP 9
STEP 10
P15
P13
P28 P12
P14
WARNING
Use this handle
to remove the
drawer.
3- Procedure for removing the drawer
Left Right
P2
P3
P5
1 - Fit the drawers - already assembled- between parts
P2 and P3, through the drawer slides.
2 - Check that the drawer slides on both sides are
properly fitted. If they are not properly fitted, the drawer
will not close completely. Slide the drawer in and out to
test it and be sure it is sliding smoothly.

1 -Insert product logo
STEP 11

FORTRESS GARAGE WARRANTS TERMS
This product has the guarantee for a period of twelve (12) months, this limited warranty is effective from the date of
the original consumer purchase. Proof of original purchase date is required to obtain service or replacement under
this limited warranty. Once the defect of manufacture has been verified, the consumer should contact the store where
he purchased the product. In the warranty period, any defective parts will be replaced free of charge by another of
the same line and model. The installation and assembly in the residence of the costumer is not the responsibility of
the factory or the store. The assembly must correctly follow the instructions inside the packaging of each module.
ITEMS EXCLUDED FROM WARRANT S
This limited warranty does not cover:
1. In-home service including, but not limited to, service calls to correct the installation of any Manhattan Comfort
Fortress Garage products or to instruct the consumer on how to use or install them.
2. Damage resulting from improper handling or shipping of products , or products damaged by accident, alteration,
misuse, abuse, fire, flood, improper installation, acts of God, neglect, corrosion, modification or mishandling.
3. All travel, transportation, shipping or freight fee s to deliver replacement products or to return de fective products.
4. Factory specified replacement parts or product replacement when your product is used in other than normal,
single-family household use, such as a commercial environment or handled in a m anner contrary to published user
or operator instructions and/or installation instructions.
5. Aesthetic damages including scratches, dings, dents or cracks that do not affect the structural or functional
capability of the product.
6. Any labor costs during the limited warranty period.
7. Damage resulting from improper loading beyond the specified maximum weight capacity outlined in the assembly
instructions provided with the product including overloading of hooks, baskets, shelves, cabinets, and other
Manhattan Comfort Fortress Garage accessories used with the product.
8. Surfaces damaged due to chemical interaction resulting in corrosion of paint or metal.
9. Replacement keys or locking mechanism.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANT Y
Implied warranties, including any implied warranty of merchantability or implied warrant of fitness for a particular
purpose, are limited to one year or shortest period allo wed by law.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
Your sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Manhattan
Comfort Fortress Garage shall not be liable for incidental or consequential damages.
TAKING GOOD CARE OF YOUR CABINET
Cleaning and caring instructions:
Avoid dragging objects on top of the cabinet. They might scratch the finishing.
Only non-abrasive natural chemical products are recommended to clean your cabinet. Simply wipe the cabinet down
with a wet cloth to remove the cleaning product excess.
Never clean the cabinet with scouring powders, steel scrubber pads or any other product which can scratch its
surface.
Chemical products are not recommended.
Cabinet surfaces should not be covered with colored plastic or paper sheets.
Acid substances must remain properly stored in sealed containers.
Avoid the direct contact of water with other surfaces, as the humidity can affect the durability of the cabinets.
Avoid cabinets exposure to direct Sun light. Drapers suggested.
This guidance should be saved for future reference, if necessary.
Stuck? Questions? We are here to help.
1-888-230-2225
[email protected]