Manhattan Comfort 9GMC1 User manual

Stuck? Questions? We are here to help.
1-888-230-2225
[email protected]
1000010414 - 13/03/2019
Tall Cabinet
Model: 9GMC1 / 9GMC2 / 9GMC3 / 9GMC4
Assembly Guide

In order to ease the assembly,
you should separate and identify the parts first
Do not place the parts directly onto the floor.
Use a cardboard sheet or a mat to place the
parts, during the separation and assembly.
*Tools Needed (not supplied)
IMPORTANT
In order to avoid severe or even fatal injuries, follow the
instructions carefully.
IDENTIFICATION OF PARTS
Nº DESCRIPTION BLACK MATT WHITE MATT BLUE GRAY MATERIAL LENGTH WIDTH THICKNESS
P1 LEFT SIDE SMART 3000009160 3000009313 3000009263 - STEEL 1 PC 25.19'' 13.74'' 0.62''
P2 RIGHT SIDE SMART 3000009161 3000009314 3000009265 - STEEL 1 PC 25.19'' 13.74'' 0.62''
P3 CEILING 1 DOOR SMART 3000009414 3000009412 3000009408 - STEEL 1 PC 13.70'' 13.62'' 0.59''
P4 REAR 1 DOOR SMART 3000009154 3000009308 3000009267 - STEEL 1 PC 13.70'' 13.38'' 1.33''
P5 SHELF SMART 3000009151 3000009317 3000009268 - STEEL 1 PC 13.74'' 12.79'' 0.62''
P6 BACK 1 DDOR SMART 3000009164 3000009320 3000009269 - STEEL 1 PC 24.01 12.40'' 0.62''
P7 DOOR RIGHT SMART 3000009318 3000009353 3000009270 3000009157 STEEL 1 PC 23.70'' 12.24'' 0.62''
P8 FRAME SMART FRONT 3000009172 3000009309 3000009272 - STEEL 1 PC 13.74'' 8.74'' 0.59''
P9 FRAME SMART REAR 3000009174 3000009311 3000009274 - STEEL 1 PC 13.74'' 8.74'' 0.59''
QUANTITY
DIMENSIONIDENTIFY THE COLOR OF YOUR CABINET

Lbs
Maximum weight
supported distributed
Hardware list
ASSEMBLED PRODUCT:
H: 29.92'' W:13.77'' L:13.77''
H
L W
P1
P6
P7 P2
P3
P5
P4
P8 P9
22 Lbs
22 Lbs
22 Lbs
F1
1000008297
Qty. 2
F2
1000008616
Qty. 2
F3
1000009033
Qty. 1
F5
1000010136
Qty. 1
F6
1000008285
Qty. 2
F8
1000008285
Qty. 1
F4
1000000281 - WHITE
1000007352 - BLACK
1000010221 - BLUE
Qty. 2
F7
3000009645 - WHITE
3000009643 - BLACK
3000009649 - BLUE
3000009647 - GREY
Qty. 1

P8
P9
1 - Identify the parts as figure below:
P8 with hole and P9 without hole.
P1
P2
1 - Attach the P9 part on the P1 and P2 parts in
the indicated direction.
2 - Then attachthe P8 part on the P1 and P2 parts.
P8
P9
01
01

01
03
01
02
P1
P2
1 - Check the alignment of the holes
on the fitted parts.
2 - The hole in the horizontal bar
of part P8, should be up.
P8
4x
P1
P2
1 - With the end of F3, smash the safety claw,
locking part P8 and P9 to part P1 and P2.
F3
P8
P9

01
05
01
04
1 - Identify the cutout on the top end of the P6 part.
2 - Attach the P6 part on the P1, P2 and P9 parts.
3- Slide part P6 to support on parts P1 and P2.
P6
P6
P1 P2
P9
2x
P6
1 - With the end of F3, smash the safety claw,
locking part P6 to part P1 and P2.
F3

01
07
01
06
P4
1 - Attach the joint of the front of the P4 part under the P8 part.
2 - Lower the P4 part as indicated.
P4
P4
1 - Check all the fittings before moving forward.

01
08
P3
1x
1 - Attach the P3 part on the
parts P1 and P2.
P3
2 - Pull the front of the P3 part.
P3

01
10
01
09
2x
2x 2x
P3
1 - With the end of F3, smash the fety
claw, locking part P3 to part P6.
F3
P5
1- Slightly turn the P5 part and place it inside the cabinet, as indicated.
2- Check all the fittings before continuing.

01
12
01
11
F4
2x
1 - Lay the cabinet against the wall and mark the hole.
IMPORTANT: CABINET MUST BE ATTACHED TO THE WALL
1 - Drill the wall on the marked point,
using a ½” drill bit.
½”

01
13
F1
2X
1 - Insert the metal part of the bushing into
the hole until it overcomes the wall.
WALL
2 - Pull the bushing driving it against
the wall and then push the plastic
ring until it leans close to the wall
WALL
Plastic ring
3 - Break the bushing's rods
WALL
1
WALL
2
WALL

01
15
01
1416
F2
2X
F3
1X
F4
2X
2x
2x
F4
F2
F3
1 - Insert the screw F2 into the hole of part P6
2 - Turn screw F2 with part F3 clockwise
3 - Press part F4 against the heads of the F2 screws.
F5
1x
F5
2X
1 - Attach the F5 into the P8 part.

01
17
01
1616
P7
1 - Attach the F7 handle to the door P7 as indicated below
F7
CLICK !
F7
F7
1X
P7
F6
F6
2X
1 - Attach the F6 into the P7 holes.
F6
1x
1x

01
19
01
18
P7
F5
1 - Attach part P7 to the bottom of the cabinet through part F5
2 - Finish engaging part P7 through the pivoting wrench
as shown below.
F8
1X
F8
P7
1 - Glue F8 to part P7 in the indicated area..

ATTENTION
To avoid serious or irreparable damage to the product, follow the instrucons carefully.
TAKING GOOD CARE OF YOUR CABINET
Cleaning and caring instructions:
- Avoid dragging objects on top of the cabinet. They might scratch the
finishing.
- Only non-abrasive natural chemical products are recommended to clean
your cabinet. Simply wipe the cabinet down with a wet cloth to remove the
cleaning product excess.
- Never clean the cabinet with scouring powders, steel scrubber pads or
any other product which can scratch its surface.
- Chemical products are not recommended.
- Cabinet surfaces should not be covered with colored plastic or paper
sheets.
- Acid substances like salt, onion, ketchup and mustard must remain
properly stored in sealed containers.
- Avoid the direct contact of water with other surfaces than the sink, as the
humidity can affect the durability of the cabinets.
- Avoid cabinets exposure to direct Sun light. Drapers suggested.
- For technical assistance outside Brazil, please, contact the store where
you purchased your product.
- This guidance should be saved for future reference, if necessary.
BEWARE: Do not use a damp cloth to clean the cabinet. Excessive
moisture can damage its surface.

WARRANTS TERMS
This product has the guarantee for a period of twelve (12) months, this limited warranty is effective from the date
of the original consumer purchase. Proof of original purchase date is required to obtain service or replacement
under this limited warranty. Once the defect of manufacture has been verified, the consumer should contact the
store where he purchased the product. In the warranty period, any defective parts will be replaced free of
charge by another of the same line and model. The installation and assembly in the residence of the costumer is
not the responsibility of the factory or the store. The assembly must correctly follow the instructions inside the
packaging of each module.
ITEMS EXCLUDED FROM WARRANTS
This limited warranty does not cover:
1. In-home service including, but not limited to, service calls to correct the installation of any Manhattan Comfort
Smart Diy products or to instruct the consumer on how to use or install them.
2. Damage resulting from improper handling or shipping of products, or products damaged by accident,
alteration, misuse, abuse, fire, flood, improper installation, acts of God, neglect, corrosion, modification or
mishandling.
3. All travel, transportation, shipping or freight fees to deliver replacement products or to return defective
products.
4. Factory specified replacement parts or product replacement when your product is used in other than normal,
single-family household use, such as a commercial environment or handled in a manner contrary to published
user or operator instructions and/or installation instructions.
5. Aesthetic damages including scratches, dings, dents or cracks that do not affect the structural or functional
capability of the product.
6. Any labor costs during the limited warranty period.
7. Damage resulting from improper loading beyond the specified maximum weight capacity outlined in the
assembly instructions provided with the product including overloading of hooks, baskets, shelves, cabinets,
and other Manhattan Comfort Smart Diy accessories used with the product.
8. Surfaces damaged due to chemical interaction resulting in corrosion of paint or metal.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANTY
Implied warranties, including any implied warranty of merchantability or implied warrant of fitness for a
particular purpose, are limited to one year or shortest period allowed by law.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
Your sole and exclusive remedy under this limited warranty shall be product repair as provided herein.
Manhattan Comfort Smart Diy shall not be liable for incidental or consequential damages.
Stuck? Questions? We are here to help.
1-888-230-2225
[email protected]