Manhattan Comfort Hampton Sideboard User manual

Hampton
sideboard 39.37"
888-230-2225
[email protected]
319 RIDGE RD, DAYTON, NJ08810, NEW JERSEY - UNITED STATES

1
Dimension:
W: 39.37" H: 33.86" D: 21.26"
ASSEMBLY VIDEO
Technical information
Maximum supported weight
22Lb
11Lb
Tools needed (not included)
6Lb

HARDWARE
2
A24x B08x C08x D16x E01x F04x G06x
I40x J01x K02x L01x M01x
H08x
FRONT VIEW REAR VIEW
PART
DESCRIPTION
QUANTITY
01
TOP
01
02
RIGHT SIDE
01
03
RIGHT PARTITION
01
04
LEFT PARTITION
01
05
LEFT SIDE
01
06
BASE
01
07
FEET
04
08
BIGGER BACK COVER
02
09
SMALLER BACK COVER
01
10
CENTRAL SHELF
02
11
RIGHT/ LEFT SHELF
02
12
RIGHT DOOR
01
13
LEFT DOOR
01
04
GLUE
12
01
13
06
11
10
05
07
02
07
07
03
08
09
08
10

3
STEP 1
- Insert the hardware (B) into the part (01).
- Insert the hardware (H) into the parts (03, 04).
STEP 2
STEP 3
- Connect the parts (02, 03, 04, 05, 11) with the hardware (A).
- Connect the parts (02, 03, 04, 05) onto
the part (01) with the hardware (C).
B
01
B08x
A
A
A
A
C
C
A08x
B
B
B
B
B
B
B
H
H
H
H
H
H
H
H
C
C
C
C
H
03
04
02
03
04
05
11
11
08x
C
05
01 02
03
04
08x

4
STEP 4
STEP 5
STEP 6
- Connect the part (06) onto the parts
(02, 03, 04, 05) with the hardware (A).
- Connect the parts (08, 09) with the hardware (I+G).
06
02
03
04
05
A
A08x
08
08
G+I
I
34X
G+I
G+I
G+I
G+I
G+I
09
I
G06X
- Connect the parts (07) under the part (06)
with the hardware (A).
L
USE THE GLUE (L)
BEFORE FASTENING
THE FEET (07).
07
A
06
07
07
07
08X
AA
A
A
A
A
A
A
A
A
A

5
STEP 7
STEP 8
STEP 9
- Connect the hinges (F) into the parts (12, 13)
with the hardware (D).
- Connect the part (12) onto the part (02)
and the part (13) onto the part (05)
with the hardware (D).
09
D
08x
D
D
13
12
02
05
08x
D
13
12
D
D
D
D
D
D
D
D
F
F
F
F
Attention! This step is very important!
You need to attach the furniture on the wall to avoid any tip over risk. Follow the procedures as showed below.
Pass the hardware (J) through the hole of the
part (09) as shown in the figure.
You will need a pencil to mark where you should
drill the wall with a 3/8" drill bit to put in the
hardware (E).
WALL
Approach as close as
possible to the wall.
D
D
10
10
J

6
Hardware (E), plugged in the wall.
Press the hardware wings (E) to put in the hole that you drilled in
the wall.
wings
wings
E
E
J
KM
K
Connect the hardware (J) onto the wall
with the hardware (M).
Then fasten with the hardware (K) the
hardware (J) on the part (01).