Manhattan Comfort Hampton User manual

Hampton
home office desk 40.79"
888-230-2225
[email protected]
319 RIDGE RD, DAYTON, NJ08810, NEW JERSEY - UNITED STATES

1
Dimension:
W: 53.54" H: 29.92" D: 20.86"
ASSEMBLY VIDEO
29,92"
19,68"
20,86"
11,41"
53,54"
6,61"
19,60"
14,96"
11,02"
Technical information
Maximum supported weight
11Lb
22Lb
Tools needed (not included)

2
FRONT VIEW REAR VIEW
PART
DESCRIPTION
QUANTITY
01
RIGHT SIDE
01
02
FRAME
01
03
SHELF
01
04
CROSSBAR
02
05
LEFT SIDE
01
06
TOP
01
07
FEET
02
08
BACK COVER
01
09
TOP/ BASE OF THE NICHE
02
10
SIDE OF THE NICHE
03
06
HARDWARE
A22x B04x C04x D04x E04x
F06x G08x H02x I18x
01
05
03
04
09
10
07
07
02
08
04
10
10
09
J02x

3
STEP 1
- Insert the hardware (B) in the part (06).
- Insert the hardware (F) in the parts (02, 04).
STEP 2
STEP 3
B
B
B
B
F
F
F
F
F
F
06
02
04
04
B
04x
F06x
- Connect the parts (01, 05) onto
the part (06) with the
hardware (C).
- Connect the hardware (E) onto
the parts (01, 05) with the
hardware (D).
C
C
05
C
04x
- Connect the parts (01, 02, 03, 04, 05) with the hardware (A).
01 06
E+D
E+D E+D
E+D
D
E04x
01
A
A
02
03
04
05
A
10x A
A
A
A
A
A
A
04

4
STEP 4
STEP 5
STEP 6
- Connect the parts (09, 10) with the hardware (A).
- Connect the niche onto the parts (02, 05)
with the hardware (J).
J02x
J
02
05
A
A
A
A
A
A
A
A
A
12x
09
09
10
10
10
GG
G
G
H
H
G
G
G
07
07
08x
06
- Connect the hardware (H) under
the part (06) with the hardware (G).
- Then, screw the parts (07) into the
hardware (H).

Hampton
888-230-2225
[email protected]
319 RIDGE RD, DAYTON, NJ08810, NEW JERSEY - UNITED STATES
bookcase

1
Dimension:
W: 24.80" H: 60.12" D: 12.60"
ASSEMBLY VIDEO
Technical information
Maximum supported weight
11Lb
Tools needed (not included)

2
HARDWARE
A20x B C D E F
01x 01x 04x 01x 08x
H I J K
01x 44x 02x 02x
G04x
FRONT VIEW REAR VIEW
PART
DESCRIPTION
QUANTITY
01
TOP
01
02
RIGHT SIDE
01
03
CROSSBAR
01
04
FIXED SHELF
01
05
LEFT SIDE
01
06
BASE
01
07
FEET
04
08
BACK COVER (DRILLED)
01
09
BACK COVER
03
10
ADJUSTABLE SHELF
02
01
10
04
10
06
02
05
03
07
07
07
08
09
09
09
GLUE

3
STEP 1
- Insert the hardware (F) in the parts (02, 05).
- Insert the hardware (G) in the part (03).
STEP 2
STEP 3
- Connect the parts (01, 02, 03, 04) with the hardware (A).
- Connect the part (05) onto the parts
(01, 03, 04) with the hardware (A).
G
G
A
A
A
A
A
A
A
A
G
G
F
F
F
F
F
F
F
F
02
05
03
02
04
01
03
08X
F
A04x
A
04x
05
04X
G
01
03
04

4
STEP 4
- Connect the part (06) onto the parts (02, 05) with hardware (A).
STEP 5
STEP 6
- Insert the hardware (J) as showed on detail.
- Connect the two parts (09) with the hardware (I+D).
- Connect the parts (08, 09) with the hardware (I).
A
04x
A
A
A
A
06
08
36X
I
09
D+I
02
05
D+I
D+I
D+I
09
09
A
A
08X
A
- Connect the parts (07) under the part (06)
using two screws (A) for each one.
C
USE THE GLUE (C)
BEFORE FASTENING
THE FEET (07).
07
J
02x
D
I
06
04X
07
07
07
07

WALL
5
STEP 7
STEP 8
10
10
H
Attention! This step is very important!
You need to attach to the furniture on the wall to avoid any tip over risk. Follow the procedures as showed below.
Approach as close as
possible to the wall.
Pass the hardware (H) through the hole of the
part (08) as shown in the figure.
You will need a pencil to mark where you should
drill the wall with a 3/8" drill bit to put in the
hardware (E).
wings
wings
E
Press the hardware wings (E) to put in the hole that you drilled in
the wall.
Hardware (E), plugged in the wall.
E
H
KB
K
08
Connect the hardware (H) onto the wall with hardware (B).
Then fasten with the hardware (K) the hardware (H) on the part (01).
- Insert the parts (10) as showed above.