Manhattan 461825 User manual

Installation Instruction
Above Fireplace Pull Down TV Mount
INTRODUCTION：
Please read through these instructions completely to be sure you’re comfortable with this easy
install process. Also check yourTV owner’s manual to see if there are any special requirements
for mounting yourTV.
If you do not understand these instructions or have doubts about the safety of the installation,
assembly or use of this product, contact your Customer Service.
CAUTION: Avoid potential personal injuries and property damage!
●This product is designed for use in wood stud, solid concrete, and concrete block walls
- DO NOT install into drywall alone!!
●Make sure that mountingscrews are anchored into the center of the stud. Use a stud
finder to locate the edge of the wood stud, then draw stud center line in the middle
point of the edges.
●The wall must be capable of supporting five times the weight of the TV and mount combined.
●Do not use this product for any purpose not explicitly specified by manufacturer.
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
●The temperature at the front of the fireplace mantle must never exceed 45℃（113℉）
IMPORTANT SAFETY INSTRUCTIONS
TOOLS NEEDED FOR ASSEMBLY
Wood Stud Install
Concrete Install
Wrench Pencil Level Screw driver Electric Drill Socket Wrench Stud Finder Wood Drill Bit Masonry Drill Bit Hammer
(3/8 in.)
10 mm
(7/32 in.)
5.5 mm
Model
Display size
Minimum display weight
Maximum display weight
Minimum VESA size
Maximum VESA size
Swivel range
Tilt range
Rotation range
461825/461276
40"-70"
16.5 lbs
78 lbs
200 x 200 mm
600 x 400 mm
+/- 45°
+5°/-15°
+/- 6°
Mount your television conveniently
above your fireplace using this Above
Fireplace Mount.
The mount allows you to keep
the TV safely up and out of the way
when not in use, then you can pull
it down to eye level for comfortable
viewing
1

PART INCLUDED
WARNING:This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any
parts are missing or damaged, do not return the damaged item to your dealer;
contact Customer Service. Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts for assembly
Hardware
02 03 04
06 M5x30mm x2
05 x2
07 M6 Nut x4
A M8x45mm x4
F 6mm washer x4
J ST6.3x55 Lag Bolts x4
K ￠6 washer x4
L Plastic wall Anchor x4
G 5mm washer x4 H ￠6 plastic spacer x4 I ￠8 plastic spacer x4
B M8x20mm x4 C M6x30mm x4 D M6x16mm x4 E M5x16mm x4
10 5mm Hex key x1 11 T Hex key x1
08 M6x12mm x2 09
￠6 washer x4
01
01 x1
02 x1 03 x2 04 x1
2

16 in.
ASSEMBLY
STEP 1.1: Attach Wall Plate to Wall ( Wood Stud Option )
CAUTION: Avoid potential personal injuries and property damage!
●Drywall covering the wall mustnot exceed 5/8 in.
●Minimum wood stud size: 2 x 4 in.or 38 x 89 mm. (1.5 x 3.5 in)
●Horizontal space between fasteners:16 in.
1: Locate your stud. Verify and mark the center of the stud by finding the stud edges using a pencil
and an edge-to-edge stud finder. ( fig 1.1 1.2 )
2: Drill pilot holes using a 3/16 in.diameter drill bit. ( fig 1.3 )
3: Install wall plate assembly using four lag bolts J K and Washer . Tighten the lag bolts
J only
until they are pulled firmly against the wall plate assembly. Do not over tighten. Over tightening
can damage the screw, reducing it's holding power.
16 in.
(406 mm)
1.1 1.2
1.4
3 in
3/16 in
1.3
CAUTION: Avoid potential personal injury or property damage! All lag bolts MUST BE firmly
tightened to prevent unwanted movement of the wall plate assembly. Ensure the
wall plate is securely fastened to the wall before continuing on to the next step 2.
J K
CAUTION:
DO NOT
install into
drywall alone
3

STEP 1.2: Attach Wall Plate to Wall ( Solid Concrete or Concrete Block Option )
2.1 2.2
CAUTION: Avoid potential personal injuries and property damage!
●Mount the wall plate assembly directly onto theconcrete surface
●Minimum solid concrete thickness: 8in
●Minimum concrete block size: 8x 8 x 16 in.
1. Position the wall plate template on the wall at your desired height. Level the wall plate and mark
the hole locations. (fig 2.1)
2. Drill four pilot holes using a 3/8 in.diameter masonry drill bit. (fig 2.2)
IMPORTANT: Pilot holes must be drilled to a depth of 3 in. Never drill into the mortar
between blocks.
10mm
(3/8 in.)
75mm(3 in)
J
L
L
J K
JK
2.3 2.4
3. LInsert four anchors .Be sure the anchors
are seated flush with the concrete surface.(fig 2.3)
4. Install wall plate assembly using four lag bolts and four washers . Tighten the lag bolts
only until they are pulled firmly against the wall plate assembly,but do not over tighten.
Over-tightening can damage the screw, reducing it's holding power. (fig 2.4)
4

STEP 2: Attach TV Bracket to TV
10
10
08
03
03
03
A B
F G
H I
C D E
04
04
08
4.1
4.Place a towel or blanket on a flat surface, then place your television face down on it Using the
two screws, attach the connecting rodto the bracket .
. (By 5mm hex key )(fig 3.2)
3.1 3.2
03
M6M5 M8
1.Select TV Screw Diameter
3.Attach the bracket to the back of the TV using the appropriate screws/washers (Flat Back) or
spacer/screw/washer (Round Back / Extra Space). (fig 3.1)
IMPORTANT: Ensure TV bracket is securely fastened before moving on to the next step.
2. Select TV Screw Length
Hand thread screws into the threaded
inserts on the back of your TV to determine
which screw diameter (M5, M6 or M8) to
use.
FLAT BACK ROUND BACK CABLESINSET HOLES
If your TV has a flat back AND you want your TV closer to the
wall, use the shorter screws.
Spacers and longer screws are supplied to accommodate:
● Round/irregular back TVs
● TVs with inset mounting holes
● Extra space needed for cables
Too Long
Too Short
Correct
CAUTION:
Verify adequate thread
engagement with your
screw/washer/spacer
combination AND
TV bracket
-Too short will not hold the TV.
-Too long will damage the TV.
5

STEP 3: Assemble Your Bracket
STEP 4: Hang TV onto Bracket
02
09 07
01
Assemble front panel onto TV bracket as illustrated. (fig 4.1)
Secure using four washer and four nut in the corner holes shown.
02
09
07
01
4.1
HEAVY! You may need assistance with this step.
06
Two people liftthe TV and hang the bracket
03
on the front panel
02
. Then use a Philips
screwdriver to tighten the two locking screws, which secures the bracket to the front panel
(fig 5.1)
Attach the wall plate cover 05 to the wall board.(fig 5.2)
03
02
05
5.2
5.1
6

TV ADJUSTMENTS
Adjust the spring pressure to balance the weight of the display so that it can be easily moved and will
maintain its position using either a ratchet wrench or the hex key
11
provided. (fig 6.1)
Tilt adjustment
Loosen the tilt lock knob on side, adjust the TV to desired view angle,then tighten the knob horizontal
level adjustment.
Slightly loosen the four nuts counterclockwise. Hold TV and gently turn to desired position. When level,
re-tighten the nuts to lockin the position. (fig 6.2)
11
6.1 6.2
knob
140°
+/- 6°
+/- 45°
+/- 18°
130mm
550mm
+5°
-15°
7

8