Manitowoc S model User manual

S Model QuietQube®Ice Machines
with CVD®Technology
Installation Training

³Compressor, Condenser,
Accumulator and HPCV are Outside
³Line Set is:
³High Pressure Liquid Line
³Low Pressure Suction Line
³Evaporator, Receiver and Harvest Valve in
Head Section
No Interconnecting Control Wiring!
Overview

Typical QuietQube System
Installation

Model Numbers
This training covers the following models:
CVD1085
SD1072C
SY1074C
CVD2075
SD2072C
SY2074C
CVD1885
SD1872C
SY1874C
CVD1485
SD1472C
SY1474C
CVD1285
SD1272C
SY1274C
CVD0885
SD0872C
SY0874C
CVD0675
SD0672C
SY0674C
CVD Condensing UnitIce Machine Head Section

Important Information
Prior to Installation
WARNING
PERSONNEL INJURY POTENTIAL
Do not operate equipment that has been misused,
abused, neglected, damaged, or altered/modified
from that of original manufactured specifications.
WARNING
Prior to installation make sure that all bin adapters
and ice deflectors
When using a non-Manitowoc ice storage system
with Manitowoc ice machines, contact the
manufacturer to assure their ice deflector is
compatible with Manitowoc ice machines.
³Read Installation, Use & Care Manual
S Model QuietQube ice machines cannot
be stacked.
Failure to follow installation guidelines may
affect warranty coverage.
Manitowoc remote systems are only
approved and warranted as a complete
new package. Warranty on the
refrigeration system will be void if a new
ice machine head section is connected to
pre-existing (used) tubing or condensing
units or vice versa.

Verify Components
³Bin
³Adapters
³Kits
³Location
Next verify that you have all the correct components
for the ice machine that is being installed

Installation Requirements
The location selected for the ice machine must meet the following criteria. If
any of these criteria are not met, select another location.
³Must have open site (gravity) drain available (see Water Supply and Drain
Requirements).
³Must have a grounded, polarized electrical power supply on a dedicated
electrical circuit (only appliance on circuit). If GFCI (ground fault circuit
interrupter) is required by your local electrical code, it must be breaker type,
not outlet type.
³Must have cold water supply line available at Ice Machine (see Water Supply
and Drain Requirements).
³Clearance and air temperatures must be met.

Head Section
Clearances
Top 5” (12.7 cm) is recommended for efficient operation and removal of top
cover/servicing.
Sides 5” (12.7 cm) is recommended for efficient operation and servicing.
There is no minimum clearance required.
Back 3” (7.6 cm) required when routing electrical inlet, water inlet and
refrigeration tubing out of the top of the unit.
5” (12.7 cm) required when routing all connections out the back.
³The air temperature must be at least 35°F (1.6°C), but must not
exceed 110°F (43.4°C).
³The location must be free of airborne and other contaminants.
³The location must not be near heat-generating equipment or in
direct sunlight.
³The location must not obstruct airflow through or around the ice
machine.

Location of Condensing Unit
³The air temperature must be at least -20°F (-28.9°C) but must
not exceed 130°F (54.4°C).
³CVD675/CVD1185/CVD2075 Only - The air temperature must
be at least -20°F (-28.9°C) but must not exceed 120°F (48.9°C).
³CVD1486 Only- The air temperature must be at least 50°F
(10°C) but must not exceed 110°F (43°C).
³The location must not allow exhaust fan heat and/or grease to
enter the condenser.
³The location must not obstruct airflow through or around the
condensing unit.

Condensing Unit Clearances
CVD675/CVD885/CVD1085/CVD1185/CVD2075
Top/Sides
There is no minimum clearance required, although 6” (15.2 cm)
is recommended for efficient operation and servicing only.
Front/Back
48” (122 cm)
CVD1285/CVD1485/CVD1885
Top/Sides
There is no minimum clearance required, although 6” (15.2 cm)
is recommended for efficient operation and servicing only.
Front
24” (61 cm)
Back
48” (122 cm)
CVD1486 ONLY
Top - 5” (12.7 cm) is required for efficient operation and
servicing.
Front/Back/Sides - 12” (30.5 cm)