Maple Systems HMC4043A-M Series User manual

Product Description:
HMC4043A-M: 4.3”, 480 x 272 pixels, WQVGA color TFT
with 4-wire analog resistive touch screen with 2 serial
ports*, one USB Device port & 1 USB Host port. It supports
1 expansion module.
* Refer to the communication section for more details.
Contents:
1ea HMC4043A-M (bagged and sealed)
1ea Mounting kit (4ea mounting clips)
1ea Input Power connector plug
1ea Quick Strat Guide
Perform the following steps to configure and use the
HMC4000 Series unit:
1. Install MAPware-7000 software.
2. Create your project.
3. Connect a programming cable (USB or Ethernet).
4. Save your project.
5. Download project to HMC4043 (note: you must select
the Download Firmware option for the initial download).
6. The HMC4000 unit is ready to use in the system.
Power (Base)
24VDC(+20%, -15%), 160mA, 3.84W
Power
(With 1 Expansion)
24VDC(+20%, -15%), 210mA, 5.04W
Display
4.3” WQVGA color TFT with 4-wire analog resistive
touch screen
LEDs
1
RAM Memory
512MB
User Application
Up to 1GB that includes user application, data log,
alarms, retentive memory and logic memory
eMMC
4GB
RTC
Built-in, date and time function
Expansion
It supports 1 expansion slot
Weight
Approx. 400gm
Panel Cutout
111.00mm(W) x 80.00mm(H)
Product
Dimensions
120.00mm(W) x 89.0mm(H) x 31.5mm(D)
Communication
Serial Port*
1 x RS232, RS485
USB Ports
1 USB Device and 1 USB Host
Ethernet
1 Ethernet Port
SD Card
Micro SD [High Capacity (4GB to 32GB)]
Speed Class:
[While inserting and removing SD card, please make
sure to TURNOFF the power to the unit.]
Environment & Approvals
Operating
Temperature
0° to 50°C
Storage
Temperature
-20° to 85°C
Humidity
10 to 90% (Non-Condensing)
Shock
IEC 60068-2-27
25g, 11ms, 6 shocks per axis, total 18 shocks (X, Y,
Z)
Vibration
IEC 60068-2-6
5 to 150Hz, 3g peak (X, Y, Z)
EMC
EN 55011 : 2009/A1 : 2010
EN 61131-2 : 2007
EN 61000-6-2 : 2005/AC : 2005
EN 61000-6-4 : 2007/A1 : 2011
Protection
IP66 for front panel mounting
APPROVALS
CE, UL (Class1 Div2) & RoHS
[* Note: HMC4043A-M support one DB9 port that supports RS232 & RS485
levels on different pins. “Y” type cable can be used for separate RS232 and
RS485 levels simultaneously.]
(Part No.: 7431-0122)
SPECIFICATIONS
PRODUCT DIMENSIONS
Panel Cutout Dimensions: 111.00 x 80.00mm,
Panel Thickness: Maximum 6mm
Mounting Clamps: 4
QUICK START GUIDE
HMC4043A-M Series
GETTING STARTED
For More Information, visit
https:\\www.maplesystems.com
AW-10114043AM Rev. 00, 02/18/22

This section provides information regarding communication interfaces
supported by this product.
Serial Port
1 Physical Port : Com1-RS232, Com2-RS485
DB9 Female
Pin number
Signal
1
TX+
2
TXD
3
RXD
4
RX+
5
SG
6
NC
7
NC
8
TX-
9
RX-
Y Type Cable
Special “Y” cable for HMC unit (two communication levels on
one port).
Cable Diagrams:
PC to unit programming cable: RS232 Pinout
CONTROL DRAWING NO# CNTL/DWG/1011-4043AM
WARNING:
-> This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D
or non- hazardous locations only.
-> WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless
power has been removed or the area is known to be non-hazardous.
-> WARNING – EXPLOSION HAZARD - Substitution of components may impair
suitability for Class I, Division 2.
-> WARNING - CAUTION, Battery May Explode If Mistreated. Do Not Recharge,
Disassemble or Dispose of in Fire.
-> The list of materials used in the construction of these devices with name of
sealed device - generic name of the material and the supplier's name and type
designation.
-> It is recommended that the user periodically inspect the sealed devices
used, for any degradation of properties and Replace the device if any
degradation is found.
Rev.
Description
Date
0
Initial release
02/18/2022
Maple Systems Inc® reserves the right to change or discontinue
specifications and features without prior notice.
To view the latest and updated datasheets/manuals, please visit
www.maplesystems.com.
REVISION HISTORY
2 Wire RS485 connections:
4 Wire RS485 connections:
USB Slave Port
1.USB Slave, compliant with micro USB 2.0 specification, self-
powered device.
2. Connector used: Micro USB Type B Female connector.
USB Host Port
1. USB Host, compliant with USB 2.0 specification.
2. USB Host can handle only USB memory stick devices and
can source current up to 150mA only.
3. Connector used: Standard USB Type a Female connector.
Ethernet Port
1. Fully compliant with IEEE 802.3 / 802.3u standards.
2. 10/100Mbps support.
3. Connector used: Standard shielded RJ-45 female jack with
in-built speed and link activity indication LEDs.
Pin number
Signal
1
TX+
2
TX-
3
RX+
4
NC
5
NC
6
RX-
7
NC
8
NC
Earthing
The optimum method for Earthing electronic equipment is to earth
it separately from other high-power systems, to earth more than one
unit of electronic equipment with a single-point earth. The Earthing
marked terminal (see below) is provided on the unit.
[Note: Do not use an earth that has an unstable impedance, such as
painted screws or earth subject to vibration.]
HMC4043A-M
AW-10114043AM Rev. 00, 02/18/22