Maretron DSM800 User manual

Revision 1.0 Page i
®®
DSM800
Vessel Monitoring and Control
Indoor Display
User’s Manual
Revision 1.0
Copyright © 2011 Maretron, LLP All Rights Reserved
Maretron, LLP
9014 N. 23rd Ave #10
Phoenix, AZ 85021-7850
http://www.maretron.com
Maretron Manual Part #: M003002

DSM800 User’s Manual
Page ii Revision 1.0
Revision History
Rev. Description
1.0 Original document

Revision 1.0 Page iii
®®
Table of Contents
1General..........................................................................................................................................1
1.1Introduction ........................................................................................................................1
1.2Firmware Revision .............................................................................................................2
1.3DSM800 Features..............................................................................................................2
1.4DSM800 Accessories.........................................................................................................2
1.5Quick Install........................................................................................................................2
2Installation......................................................................................................................................3
2.1Unpacking the Box.............................................................................................................3
2.2Choosing a Mounting Location...........................................................................................3
2.3Mounting the DSM800........................................................................................................3
2.3.1Wall Mounting...............................................................................................................3
2.3.2Panel Mounting.............................................................................................................5
2.3.3Arm Mounting ...............................................................................................................7
2.4Connecting the DSM800....................................................................................................8
2.4.1LAN Connection............................................................................................................9
2.4.2USB Device Connection .............................................................................................10
2.4.3Power Connection.......................................................................................................10
2.4.4Power Sequencing......................................................................................................11
2.5Configuring the DSM800..................................................................................................11
2.5.1Manually Entering LAN Connection Information.........................................................12
2.5.2Entering N2KServer®or IPG100 Connection Information...........................................14
3Operating the DSM800................................................................................................................17
3.1Turning the DSM800 On ..................................................................................................17
3.2Turning the DSM800 Off ..................................................................................................17
3.3Using the DSM800...........................................................................................................17
4Maintenance................................................................................................................................18
5Troubleshooting...........................................................................................................................19
6Technical Specifications ..............................................................................................................20
7Technical Support........................................................................................................................21
8Maretron (1 Year) Limited Warranty ............................................................................................22

DSM800 User’s Manual
Page iv Revision 1.0
Table of Figures
Figure 1 – DSM800 Network Diagram..................................................................................................1
Figure 2 – Wall Mounting Bracket.........................................................................................................4
Figure 3 – Chassis Support Screws......................................................................................................4
Figure 4 – Secure the DSM800.............................................................................................................5
Figure 5 – DSM800 Cutout Dimensions (units in mm)..........................................................................6
Figure 6 – Tighten the Panel Mounting Clamp Screws.........................................................................7
Figure 7 – DSM800 Arm Mounting Retention Screw Holes ..................................................................8
Figure 8 – DSM800 Interface Connector Panel ....................................................................................9
Figure 9 – LAN Connection...................................................................................................................9
Figure 10 – USB Device Connection ..................................................................................................10
Figure 11 – DSM800 Startup Screen..................................................................................................11
Figure 12 – N2KView®Window with Tabs Displayed..........................................................................12
Figure 13 – Configuration Dialog ........................................................................................................13
Figure 14 – N2KView®Window with Tabs Displayed..........................................................................14
Figure 15 – Connections Settings Dialog............................................................................................15

®®
1 General
1.1 Introduction
Congratulations on your purchase of the Maretron DSM800 Vessel Monitoring and Control Indoor
Display. Maretron has designed and built your display to the highest standards for years of
dependable and accurate service.
The DSM800 is a dedicated touch screen that comes preloaded with Maretron’s N2KView®vessel
monitoring and control software (N2KView®hardware license key sold separately). The N2KView®
software allows you to configure as many favorite screens as you want with exactly the information
you want to see. Although not suitable for outdoor applications, the DSM800 provides an extremely
simple touch interface for monitoring and controlling critical systems from inside the vessel.
The DSM800 is ruggedized for marine use and includes a solid state disk drive to withstand the
pounding associated with waves. And since the DSM800 only dissipates 25 watts, there is no need
for internal cooling fans that are noisy and wear out causing electronics to overheat and fail.
As an alternative to controlling the DSM800 through the touch screen, the DSM800 includes two USB
ports for connecting keyboards, mice, or trackballs. The DSM800 also has an Ethernet port for
communicating with an NMEA 2000®network (see Figure 1) through Maretron’s Internet Protocol
Gateway (IPG100). Alternatively, the DSM800 can network through Ethernet to a PC running
N2KServer®. Although the DSM800 comes pre-installed with the N2KView®software, a separately
purchased N2KView®hardware license key plugged into the IPG100 (or PC) is required (see IPG100
User’s Manual for more details). The Ethernet port is also used for connecting Internet Protocol (IP)
cameras for viewing within the N2KView®software.
Figure 1 – DSM800 Network Diagram
Revision 1.0 Page 1

DSM800 User’s Manual
Page 2 Revision 1.0
he Maretron DSM800 is designed to operate within the harsh demands of the marine environment.
1.2 Firmware Revision running N2KView®Version 3.2.
1.3 DSM800 Features g features. ch Screen
Keyboards and Mice Video
1.4 DSM800 Accessories the DSM800:
1.5 Quick Install display involves the following five steps. Please refer to the individual
ection 2.2)
T
However, no piece of marine electronic equipment can function properly unless installed, configured,
and maintained in the correct manner. Please read carefully and follow these instructions for
installation, configuration, and usage of the Maretron DSM800 in order to ensure optimal
performance.
This manual corresponds to the DSM800
The Maretron DSM800 has the followin
•8” LED Backlit LCD Panel with Resistive Tou
•800 x 600 Pixels ess•300 nits of brightn
•Solid State Disk Drive
•Fanless cooling system
•USB Ports for connecting
•Ethernet Port for Receiving Networked Data and
Maretron offers the following accessories for
•MAFLPK-12 Panel Mounting Kit
•MAFLWK-12 Wall Mounting Kit VDC input power adapter:•DC/DC-01 60 W DC/DC 9-30
Installing the Maretron DSM800
sections for additional details.
•Unpacking the Box (Section 2.1)
•Choosing a Mounting Location (S
•Mounting the DSM800 (Section 2.3) )•Connecting the DSM800 (Section 2.4
•Configuring the DSM800 (Section 2.5)

®®
Revision 1.0 Page 3
2 Installation
2.1 Unpacking the Box
When unpacking the box containing the Maretron DSM800, you should find the following items:
•1 – DSM800 Vessel Monitoring and Control Indoor Display
•1 – 63000-FSP0481AC101C-RS AC Power Adapter
•1 – 32000-000002-RS AC Power Cord
•1 - 12VDC Pigtail (90° Connector)
•1 – 44013-030041-RS Screw Kit
•1 – XTR103-0002-RS Touch Pen
•1 – DSM800 User’s Manual
•1 – N2KView®Documentation CD-ROM
•1 – Warranty Registration Card
If any of these items are missing or damaged, please contact Maretron.
2.2 Choosing a Mounting Location
The DSM800 front panel is splash proof (IEC IP64 rating – protected against the effects of splashed
water). , Although the front panel is splash proof, the display panel is intended for indoor use only (it
is not day light or sun light readable), so the DSM800 should be mounted in an indoor location.
2.3 Mounting the DSM800
The DSM800 has three mounting options, which include:
•wall mounting (if access to the backside of the mounting surface is not available, requires
purchase of MAFLWK-12 wall mounting Kit accessory),
•panel mounting (requires purchase of optional MAFLPK-12 Panel Mounting Kit accessory)
•arm mounting (requires purchase of a VESA 75mm mounting arm)
Maretron suggests a location at which the display can be viewed from a relatively straight angle.
2.3.1 Wall Mounting
To mount the DSM800 using the optional wall mounting kit (Maretron part number MAFLWK-12),
please follow the steps below:
Step 1: Select the location on the wall for the wall-mounting bracket.
Step 2: Carefully mark the locations of the four screw holes in the bracket on the wall.
Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention screws.
Step 4: Align the wall-mounting bracket screw holes with the pilot holes.

DSM800 User’s Manual
Page 4 Revision 1.0
Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into the four pilot
holes and tightening them (see Figure 2).
Figure 2 – Wall Mounting Bracket
Step 6: Insert the four monitor mounting screws provided in the wall mounting kit into the four screw
holes on the rear panel of the DSM800 and tighten until the screw shank is secured against
the rear panel (Figure 3).
Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on the bracket.
Step 8: Carefully insert the screws through the holes and gently pull the monitor downwards until the
monitor rests securely in the slotted holes (Figure 3). Ensure that all four of the mounting
screws fit snugly into their respective slotted holes.
Figure 3 – Chassis Support Screws

®®
Step 9: Secure the DSM800 by fastening the retention screw of the wall-mounting bracket. (Figure 4).
Figure 4 – Secure the DSM800
2.3.2 Panel Mounting
To mount the DSM800 using the optional panel mounting kit (Maretron part number MAFLPK-12),
please follow the steps below. Please note that the clamps found within the panel mounting kit
support a maximum panel thickness of 3/8” or 0.375”.
Step 1: Select the position on the panel to mount the DSM800.
Step 2: Cut out a section from the panel that corresponds to the rear panel dimensions of the
DSM800. Take care that the panel section that is cut out is smaller than the overall size of the
metal frame that surrounds the DSM800 but just large enough for the rear panel of the
DSM800 to fit through (Figure 5).
Revision 1.0 Page 5

DSM800 User’s Manual
Page 6 Revision 1.0
Figure 5 – DSM800 Cutout Dimensions (units in mm)
Step 3: Slide the DSM800 through the hole until the aluminum frame is flush against the panel.
Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of the chassis,
behind the aluminum frame (6 clamps come with the optional panel mount kit, 4 clamps are
used, and two are extras).
Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic caps at the
front of all the screws are firmly secured to the panel (Figure 6).