Maretron DSM150 User manual

Revision 1.4.18 Page i
DSM150
NMEA 2000®Multi-function Color
Graphic Display
User’s Manual
Revision 1.4.18
Copyright © 2013 Maretron, LLP All Rights Reserved
Maretron, LLP
9014 N. 23rd Ave #10
Phoenix, AZ 85021-7850
http://www.maretron.com
Maretron Manual Part #: M003035

DSM150 User’s Manual
Page ii Revision 1.4.18
Revision History
Rev.
Description
1.4.16
Original document.
1.4.16a
Corrected Page Number Issue
Updated Received PGN List
Corrected Description of “DSM150 Running in Favorite Screens Mode” Figure
Added notes that zero re-trigger time on an alert will disable re-triggering
1.4.17
Added Configuration of VDR100 Network Parameters
Removed 127502 from Supported PGN Table
Added Configuration of SMS100
1.4.18
Added DSM150CABLE-01.0 to “Unpacking the Box” section
Added Device Configuration for SMS100
Updated Device Configuration for EMS100, IPG100,VDR100
Removed 127502 Binary Switch Control from supported PGN list
Added 130834 and 130835 to supported PGN list
Added SMS Phone Book
Added Alert Configuration for SMS Text Messages
Added Control Mode resetting of Trip Log, Total Fuel Used, Total Volume, Anchor
Watch

Revision 1.4.18 Page iii
Table of Contents
1General..........................................................................................................................................1
1.1 Introduction ........................................................................................................................1
1.2 Firmware Revision .............................................................................................................1
1.3 DSM150 Features..............................................................................................................1
1.4 Quick Install........................................................................................................................1
2Installation......................................................................................................................................2
2.1 Unpacking the Box.............................................................................................................2
2.2 Choosing a Mounting Location...........................................................................................2
2.3 Mounting the DSM150........................................................................................................2
2.3.1 Flush Mounting the DSM150 ........................................................................................2
2.4 Connecting the DSM150....................................................................................................3
2.4.1 Checking the Connection..............................................................................................3
3Operating the DSM150..................................................................................................................4
3.1 Turning the DSM150 On ....................................................................................................4
3.2 Turning the DSM150 Off ....................................................................................................4
3.3 Keypad Essentials..............................................................................................................5
3.3.1 Navigating in a Menu....................................................................................................6
3.3.2 Choosing a Value from a List........................................................................................6
3.3.3 Entering a Numeric Value.............................................................................................6
3.3.4 Entering a Textual Value...............................................................................................6
4Important Concepts .......................................................................................................................9
4.1 Favorite Screens................................................................................................................9
4.2 Categories and Data Types................................................................................................9
4.2.1 AC Bus........................................................................................................................10
4.2.2 AC Generator..............................................................................................................10
4.2.3 AC Utility.....................................................................................................................11
4.2.4 Anchor Watch.............................................................................................................12
4.2.5 DC...............................................................................................................................12
4.2.6 Depth..........................................................................................................................12
4.2.7 Elec. Distribution.........................................................................................................12
4.2.8 Engine.........................................................................................................................12
4.2.9 Environment................................................................................................................14
4.2.10 Fluid Flow ...................................................................................................................14
4.2.11 Fuel Management.......................................................................................................14
4.2.12 GPS............................................................................................................................15
4.2.13 Heading ......................................................................................................................15
4.2.14 Humidity......................................................................................................................16
4.2.15 Indicator......................................................................................................................16
4.2.16 Navigation...................................................................................................................16
4.2.17 Rudder........................................................................................................................16
4.2.18 Pressure/Vacuum .......................................................................................................16
4.2.19 Special Device............................................................................................................17
4.2.20 Speed .........................................................................................................................17
4.2.21 Tank............................................................................................................................17
4.2.22 Temperature...............................................................................................................17
4.2.23 Time/Date...................................................................................................................18
4.2.24 Transmission ..............................................................................................................18

DSM150 User’s Manual
Page iv Revision 1.4.18
4.2.25 VDR............................................................................................................................18
4.2.26 Vessel.........................................................................................................................18
4.2.27 Wind............................................................................................................................19
4.3 Alerts................................................................................................................................20
4.3.1 Alert Types..................................................................................................................20
4.3.2 Alert Terminology........................................................................................................20
4.3.3 Alert Priority................................................................................................................20
4.3.4 Vessel Alert Operating Modes ....................................................................................20
4.3.5 Alert States.................................................................................................................21
4.3.6 Available Alert Classes...............................................................................................22
5Operating Modes.........................................................................................................................23
5.1 Favorite screens modes...................................................................................................23
5.2 Menu Mode......................................................................................................................24
5.2.1 Alert Setup Menu........................................................................................................25
5.2.2 Alert Status.................................................................................................................25
5.2.3 Configuration Menu.....................................................................................................25
5.2.4 Display Settings Menu................................................................................................27
5.2.5 Favorite Screens Mode...............................................................................................34
5.2.6 Favorite Screens Setup Menu ....................................................................................34
5.2.7 Units Menu..................................................................................................................38
5.3 Control Mode....................................................................................................................41
6Device Configuration ...................................................................................................................43
6.1 Airmar Depth/Speed/Temperature Transducers ..............................................................46
6.1.1 Advanced Configuration..............................................................................................46
6.1.2 Device Instance ..........................................................................................................47
6.1.3 Installation Description................................................................................................47
6.1.4 NMEA2000 PGN Enable/Disable................................................................................47
6.1.5 Clear Speed Calibration..............................................................................................47
6.1.6 Speed Calibration .......................................................................................................48
6.1.7 Clear Temperature Offset...........................................................................................48
6.1.8 Temperature Calibration.............................................................................................49
6.1.9 Transducer Depth Offset.............................................................................................49
6.1.10 Trip Log.......................................................................................................................50
6.2 Bennett EP-30 (NMEA1) Trim Tabs Configuration...........................................................51
6.2.1 Trim Tabs Calibration..................................................................................................51
6.3 Maretron ACM100 Configuration......................................................................................53
6.3.1 Advanced Configuration..............................................................................................53
6.3.2 AC Circuit Type...........................................................................................................56
6.3.3 AC Device Type..........................................................................................................56
6.3.4 Device Instance ..........................................................................................................56
6.3.5 Label...........................................................................................................................56
6.3.6 Reset Total Energy Recorded.....................................................................................57
6.4 Maretron ALM100 Configuration......................................................................................58
6.4.1 Advanced Configuration..............................................................................................58
6.4.2 Instance......................................................................................................................59
6.4.3 Label...........................................................................................................................59
6.4.4 Test Annunciator.........................................................................................................60
6.5 Maretron DCM100 Configuration .....................................................................................61

Revision 1.4.18 Page v
6.5.1 Advanced Configuration..............................................................................................61
6.5.2 Current Sensor Zero Offset Calibration.......................................................................63
6.5.3 DC Type......................................................................................................................64
6.5.4 Instance......................................................................................................................66
6.5.5 Label...........................................................................................................................66
6.6 Maretron DCR100 Configuration......................................................................................67
6.6.1 Advanced Configuration..............................................................................................67
6.6.2 Device Label...............................................................................................................69
6.6.3 Instance......................................................................................................................69
6.6.4 Channel #1-#6 Configuration......................................................................................69
6.7 Maretron DSM200 Configuration......................................................................................71
6.7.1 Remote Device Selection............................................................................................72
6.8 Maretron DSM150, DSM250 Configuration......................................................................74
6.8.1 Remote Device Selection............................................................................................74
6.8.2 Copy alarms settings from local display......................................................................75
6.8.3 Copy device selection from local display ....................................................................76
6.8.4 Copy display settings from local display .....................................................................77
6.8.5 Copy favorite settings from local display.....................................................................77
6.8.6 Copy DST100 calibrations from local display..............................................................78
6.8.7 Copy all settings from local display.............................................................................78
6.8.8 Label...........................................................................................................................79
6.8.9 Remote Device Selection............................................................................................80
6.9 Maretron DST100 Configuration ......................................................................................81
6.9.1 Advanced Configuration..............................................................................................81
6.9.2 Clear Speed Calibration..............................................................................................82
6.9.3 Speed Calibration .......................................................................................................82
6.9.4 Transducer Depth Offset.............................................................................................83
6.9.5 Trip Log.......................................................................................................................83
6.10 Maretron DST110 Configuration ......................................................................................85
6.10.1 Advanced Configuration..............................................................................................85
6.10.2 Clear Speed Calibration..............................................................................................86
6.10.3 Speed Calibration .......................................................................................................87
6.10.4 Clear Temperature Offset...........................................................................................87
6.10.5 Temperature Calibration.............................................................................................88
6.10.6 Transducer Depth Offset.............................................................................................88
6.10.7 Trip Log.......................................................................................................................89
6.11 Maretron EMS100 Configuration......................................................................................90
6.11.1 Engine Instance..........................................................................................................90
6.11.2 Boost Pressure Gauge Type.......................................................................................90
6.11.3 Boost Pressure Sender Type......................................................................................91
6.11.4 Boost Pressure Sender Offset....................................................................................91
6.11.5 Drive Trim Gauge Type...............................................................................................91
6.11.6 Drive Trim Sender Type..............................................................................................91
6.11.7 Drive Trim Sender Offset............................................................................................92
6.11.8 Oil Pressure Gauge Type ...........................................................................................92
6.11.9 Oil Pressure Sender Type...........................................................................................92
6.11.10Oil Pressure Sender Offset.........................................................................................92
6.11.11Water Temperature Gauge Type................................................................................93

DSM150 User’s Manual
Page vi Revision 1.4.18
6.11.12Water Temperature Sender Type ...............................................................................93
6.11.13Water Temperature Sender Offset..............................................................................93
6.11.14Preset Engine Hours...................................................................................................93
6.11.15Tachometer Flywheel Teeth .......................................................................................94
6.12 Maretron FFM100 Configuration......................................................................................95
6.12.1 Advanced Configuration..............................................................................................95
6.12.2 Device Label...............................................................................................................97
6.12.3 Operating Mode..........................................................................................................97
6.12.4 Channel #0…..............................................................................................................97
6.12.5 Channel #1…............................................................................................................102
6.13 Maretron FPM100 Configuration....................................................................................106
6.13.1 Advanced Configuration… ........................................................................................106
6.13.2 Channel #0-5............................................................................................................108
6.14 Maretron GPS100 Configuration....................................................................................115
6.14.1 Advanced Configuration............................................................................................116
6.14.2 Cold Start GPS .........................................................................................................120
6.14.3 GPS Mode Setting....................................................................................................120
6.14.4 Device Label.............................................................................................................121
6.14.5 SBAS (WAAS) Enable/Disable .................................................................................121
6.15 Maretron GPS200 Configuration....................................................................................123
6.15.1 Advanced Configuration............................................................................................123
6.15.2 Cold Start GPS .........................................................................................................125
6.15.3 Device Label.............................................................................................................125
6.15.4 SBAS (WAAS,EGNOS,MSAS) Enable/Disable ........................................................125
6.16 Maretron IPG100 Configuration .....................................................................................127
6.16.2 Device Label.............................................................................................................130
6.16.3 N2KServer Password................................................................................................130
6.16.4 Maretron Cloud Services ..........................................................................................130
6.16.5 DHCP........................................................................................................................130
6.16.6 IP Address................................................................................................................131
6.16.7 Subnet Mask.............................................................................................................131
6.16.8 Default Gateway .......................................................................................................131
6.16.9 Default DNS..............................................................................................................131
6.17 Maretron J2K100 Configuration .....................................................................................131
6.17.1 Advanced Configuration............................................................................................132
6.17.2 Device Label.............................................................................................................134
6.17.3 NMEA 2000 Instance –Engine.................................................................................134
6.17.4 Transmission Instance..............................................................................................135
6.17.5 AC/Icemaker Instance...............................................................................................136
6.17.6 J1939 Source Address Configuration .......................................................................136
6.17.7 Refresh J1939 source address list............................................................................137
6.18 Maretron NBE100 Configuration....................................................................................137
6.18.1 Advanced Configuration............................................................................................138
6.19 Maretron RAA100 Configuration....................................................................................138
6.19.1 Advanced Configuration............................................................................................139
6.19.2 Label.........................................................................................................................140
6.19.3 Rudder Angle Calibration..........................................................................................141
6.19.4 Rudder Number ........................................................................................................144

Revision 1.4.18 Page vii
6.19.5 Operating Mode........................................................................................................145
6.19.6 Gauge Resistance, + to Sender................................................................................146
6.19.7 Gauge Resistance, - to Sender.................................................................................146
6.20 Maretron RIM100 Configuration.....................................................................................148
6.20.1 Advanced Configuration............................................................................................148
6.20.2 Device Label.............................................................................................................149
6.20.3 Instance....................................................................................................................150
6.20.4 Channel Configuration..............................................................................................150
6.21 Maretron SIM100 Configuration.....................................................................................151
6.21.1 Advanced Configuration............................................................................................151
6.21.2 Device Label.............................................................................................................152
6.21.3 Instance....................................................................................................................153
6.21.4 Channel Configuration..............................................................................................153
6.22 Maretron SMS100 Configuration....................................................................................154
6.22.1 Advanced Configuration............................................................................................154
6.22.2 Label.........................................................................................................................155
6.22.3 Test… .......................................................................................................................156
6.23 Maretron SSC200 Configuration....................................................................................157
6.23.1 Advanced Configuration............................................................................................157
6.23.2 157
6.23.3 Installation Offset Calibration....................................................................................160
6.23.4 Inverted Installation Entry .........................................................................................161
6.23.5 Label.........................................................................................................................162
6.23.6 Magnetic Deviation Calibration .................................................................................162
6.23.7 Magnetic Deviation Status........................................................................................163
6.23.8 Rate of Turn Damping Period...................................................................................163
6.23.9 Rate of Turn Zero Offset Calibration.........................................................................164
6.23.10Variation Source Entry..............................................................................................164
6.24 Maretron TLA100 Configuration.....................................................................................168
6.24.1 Advanced Configuration............................................................................................168
6.24.2 168
6.24.3 Label.........................................................................................................................169
6.24.4 Tank Capacity...........................................................................................................170
6.24.5 Tank Levels Calibration ............................................................................................171
6.24.6 Tank Number............................................................................................................175
6.24.7 Tank Type.................................................................................................................175
6.24.8 Operating Mode........................................................................................................176
6.24.9 Gauge Resistance, + to Sender................................................................................177
6.24.10Gauge Resistance, - to Sender.................................................................................177
6.25 Maretron TLM100 Configuration ....................................................................................179
6.25.1 179
6.25.2 Advanced Configuration............................................................................................179
6.25.3 Label.........................................................................................................................180
6.25.4 Tank Capacity...........................................................................................................180
6.25.5 Tank Levels Calibration ............................................................................................181
6.25.6 Tank Number............................................................................................................186
6.25.7 Tank Type.................................................................................................................186
6.26 Maretron TLM150 Configuration ....................................................................................186

DSM150 User’s Manual
Page viii Revision 1.4.18
6.27 Maretron TLM200 Configuration ....................................................................................186
6.28 Maretron TMP100 Configuration....................................................................................187
6.28.1 Advanced Configuration............................................................................................187
6.28.2 187
6.28.3 Channel Configuration..............................................................................................189
6.28.4 Device Label.............................................................................................................190
6.29 Maretron USB100 Configuration....................................................................................191
6.29.1 Advanced Configuration............................................................................................191
6.29.2 Remote Device Selection..........................................................................................192
6.30 Maretron VDR100 Configuration....................................................................................193
6.30.1 Advanced Configuration ........................................................................................193
6.30.2 Label.........................................................................................................................194
6.30.3 Password..................................................................................................................194
6.30.4 DHCP........................................................................................................................194
6.30.5 IP Address................................................................................................................194
6.30.6 Subnet Mask.............................................................................................................194
6.30.7 Default Gateway .......................................................................................................195
6.30.8 Default DNS..............................................................................................................195
6.31 Maretron WSO100 Configuration...................................................................................195
6.31.1 195
6.31.2 Advanced Configuration............................................................................................196
6.31.3 Device Label.............................................................................................................197
6.31.4 Installation Offset Calibration....................................................................................198
6.31.5 Wind Data Damping Period ......................................................................................200
6.31.6 Barometric Pressure.................................................................................................200
6.31.7 Outside Humidity.......................................................................................................201
6.31.8 Outside Temperature................................................................................................201
7Data Display Types....................................................................................................................203
7.1 Anchor Watch Display....................................................................................................203
7.2 Compass Rose Display..................................................................................................205
7.3 Gauge Display................................................................................................................206
7.4 GPS Status Display........................................................................................................207
7.5 Numeric Display.............................................................................................................208
7.6 Rolling Road...................................................................................................................209
7.7 Line Graph .....................................................................................................................210
7.8 Weather Display.............................................................................................................210
7.9 Wind Rose......................................................................................................................212
7.10 Moon Phase Display ......................................................................................................212
7.11 Trim Tab Display............................................................................................................212
7.12 Swing Meter Display ......................................................................................................213
7.13 Tank Gauge Display.......................................................................................................213
7.14 Switch/Breaker Display ..................................................................................................214
8Alerts..........................................................................................................................................218
8.1 Displaying Active Alerts..................................................................................................218
8.1.1 Alert Status Screen...................................................................................................218
8.2 Accepting or Cancelling an Alert....................................................................................219
8.2.1 From a Favorite Screen............................................................................................219
8.2.2 From the Alert Status Screen....................................................................................219

Revision 1.4.18 Page ix
8.3 Adding an Alert...............................................................................................................220
8.3.1 Enable/Disable Control.............................................................................................221
8.3.2 Alert Type .................................................................................................................221
8.3.3 Priority.......................................................................................................................221
8.3.4 Trigger Source..........................................................................................................222
8.3.5 Description................................................................................................................222
8.3.6 Location....................................................................................................................222
8.3.7 Trigger Configuration................................................................................................222
8.3.8 Local Audible............................................................................................................236
8.3.9 Tone..........................................................................................................................236
8.3.10 Remote Annunciators ...............................................................................................237
8.3.11 SMS (Text) Settings… ..............................................................................................237
8.3.12 Operating Mode Moored...........................................................................................238
8.3.13 Operating Mode Underway.......................................................................................239
8.3.14 Operating Mode Anchored........................................................................................239
8.3.15 Scope........................................................................................................................239
8.4 Deleting an Alert.............................................................................................................239
8.5 Editing an Alert...............................................................................................................241
8.6 Setting the Vessel Operating Mode................................................................................242
8.7 SMS (Text) Phone Book.................................................................................................243
8.8 Advanced Configuration.................................................................................................245
8.8.1 Remote Alert Audible................................................................................................246
8.8.2 Flashing Screen........................................................................................................246
8.9 Restore Factory Defaults................................................................................................246
9Maintenance..............................................................................................................................248
10 Troubleshooting.........................................................................................................................249
11 Technical Specifications ............................................................................................................250
12 Technical Support......................................................................................................................255
13 Installation Template..................................................................................................................256
14 Maretron (2 Year) Limited Warranty ..........................................................................................257

DSM150 User’s Manual
Page x Revision 1.4.18
Table of Figures
Figure 1 –NMEA 2000® Connector Face View....................................................................................3
Figure 2 –DSM150 Power Up Screen..................................................................................................4
Figure 3 –Powerdown Countdown Screen...........................................................................................5
Figure 4 –Keypad and Key Names......................................................................................................5
Figure 5 –Entering a Textual Value......................................................................................................7
Figure 6 –DSM150 Running in Favorite Screens Mode.....................................................................23
Figure 7 –Main Menu.........................................................................................................................24
Figure 8 –Configuration Screen.........................................................................................................25
Figure 9 –Device Selection Screen....................................................................................................26
Figure 10 –DSM150 Display Settings Screen....................................................................................27
Figure 11 –DSM150 Advanced Configuration....................................................................................27
Figure 12 –DSM150 Primary Device Selection..................................................................................28
Figure 13 –DSM150 Advanced Information Screen...........................................................................29
Figure 14 –Bus Status Display...........................................................................................................29
Figure 15 –Backlight Menu ................................................................................................................30
Figure 16 –Color Palette Selection Screen........................................................................................31
Figure 17 –Color Palette Configuration Screen..................................................................................31
Figure 18 –Setting the Demo Mode...................................................................................................32
Figure 19 –Setting the Keyboard Beep Option...................................................................................33
Figure 20 –Editing the DSM150 Label...............................................................................................33
Figure 21 –Setting the Favorite Screens Mode..................................................................................34
Figure 22 –Favorite Screens Setup Screen.......................................................................................34
Figure 23 –Favorite Screen Parameters............................................................................................35
Figure 24 –Setting the Favorite Screen Format.................................................................................36
Figure 25 –Setting the Auto Change Interval.....................................................................................36
Figure 26 –Selecting the Data Category............................................................................................37
Figure 27 –Selecting the Data to be displayed...................................................................................37
Figure 28 –DSM150 Units Menu........................................................................................................39
Figure 29 –Device Configuration Screen ...........................................................................................44
Figure 30 –Airmar Depth/Speed/Temperature Transducer Configuration Screen .............................46
Figure 31 –Airmar Transducer Advanced Configuration Screen........................................................47
Figure 32 –Calibrating the Airmar Speed Transducer Speed ............................................................48
Figure 33 –Airmar Temperature Transducer Water Temperature Calibration Screen .......................49
Figure 34 –Setting the Transducer Depth Offset in an Airmar Depth Transducer..............................50
Figure 35 –Resetting the Airmar Speed Sensor Trip Distance Log....................................................50
Figure 36 –EP-30 Trim Tabs Configuration Screen...........................................................................51
Figure 37 –EP-30 Trim Tabs Calibration Opening Screen.................................................................51
Figure 38 –EP-30 Intermediate Calibration Screen............................................................................52
Figure 39 –EP-30 Calibration Success Message...............................................................................52
Figure 40 –ACM100 Configuration Screen ........................................................................................53
Figure 41 –ACM100 Advanced Configuration Screen .......................................................................53
Figure 42 –ACM100 NMEA 2000®PGN Enable/Disable Screen.......................................................55
Figure 43 –Reset Total Energy Recorded Confirmation Screen........................................................57
Figure 44 –ALM100 Configuration Screen.........................................................................................58
Figure 45 –ALM100 Advanced Configuration Screen........................................................................58
Figure 46 –ALM100 NMEA 2000®PGN Enable/Disable Screen .......................................................59

Revision 1.4.18 Page vi
Figure 47 –DCM100 Configuration Screen........................................................................................61
Figure 48 –DCM100 Advanced Configuration Screen.......................................................................61
Figure 49 –DCM100 NMEA 2000®PGN Enable/Disable Screen.......................................................62
Figure 50 –Current Sensor Zero Offset Calibration Confirmation Screen..........................................63
Figure 51 –Current Sensor Zero Offset Calibration Complete Screen...............................................63
Figure 52 –DCR100 Configuration Screen ........................................................................................67
Figure 53 –DCR100 Advanced Configuration Screen........................................................................67
Figure 54 –DCR100 Current Sensor Zero Offset Calibration Screen.................................................68
Figure 55 –DCR100 Current Sensor Zero Offset Calibration Completion Screen..............................68
Figure 56 –DCR100 NMEA2000 PGN Enable/Disable Screen..........................................................69
Figure 57 –DCR100 Channel Configuration Screen (DCR Mode).....................................................70
Figure 58 –DCR100 Channel Configuration Screen (ALM Mode)......................................................71
Figure 59 –DSM200 Remote Configuration Screen...........................................................................72
Figure 60 –DSM200 Remote Device Selection Screen .....................................................................72
Figure 61 –DSM150/DSM250 Remote Configuration Screen............................................................74
Figure 62 –DSM150/DSM250 Remote Device Selection Screen.......................................................75
Figure 63 –DSM150/DSM250 Copy alarms settings from local display.............................................76
Figure 64 –DSM150/DSM250 Copy device selection from local display............................................76
Figure 65 –DSM150/DSM250 Copy display settings from local display.............................................77
Figure 66 –DSM150/DSM250 Copy favorite settings from local display............................................77
Figure 67 –Favorite Settings Transfer Completion Screen ................................................................78
Figure 68 –DSM150/DSM250 Copy DST100 calibrations from local display.....................................78
Figure 69 –DSM150/DSM250 copy all settings from local display.....................................................79
Figure 70 –DSM150 Label Configuration...........................................................................................79
Figure 71 –DSM150/DSM250 Remote Device Selection...................................................................80
Figure 72 –DST100 Configuration Screen.........................................................................................81
Figure 73 –DST100 Advanced Configuration Screen........................................................................81
Figure 74 –Calibrating the DSM150 for DST100 Speed through Water.............................................82
Figure 75 –Setting the Transducer Depth Offset in a DST100...........................................................83
Figure 76 –Resetting the DST100 Trip Distance Log.........................................................................84
Figure 77 –DST110 Configuration Screen.........................................................................................85
Figure 78 –DST110 Advanced Configuration Screen........................................................................85
Figure 79 - DST110 NMEA 2000®PGN Enable/Disable Screen ........................................................86
Figure 80 –Calibrating the DST110 Speed ........................................................................................87
Figure 81 –DST110 Water Temperature Calibration Screen .............................................................88
Figure 82 –Setting the Transducer Depth Offset in a DST110...........................................................89
Figure 83 –Resetting the DST110 Trip Distance Log.........................................................................89
Figure 84 –EMS100 Configuration Screen ........................................................................................90
Figure 85 –FFM100 Configuration Screen.........................................................................................95
Figure 86 –FFM100 Advanced Configuration ....................................................................................95
Figure 87 –FFM100 NMEA PGN Enable/Disable Screen..................................................................97
Figure 88 –FFM100 Channel #0 First Configuration Screen (Differential Mode) ...............................98
Figure 89 –FFM100 Channel #0 Second Configuration Screen (Differential Mode)..........................98
Figure 90 –FFM100 Channel #0 First Configuration Screen (Two Independent Sensors Mode).....100
Figure 91 –FFM100 Channel #0 Second Configuration Screen (Two Independent Sensors Mode)100
Figure 92 –FFM100 Channel #1 Configuration Screen (Differential Mode) .....................................103
Figure 93 –FFM100 Channel #1 First Configuration Screen (Two Independent Sensors Mode).....104
Figure 94 –FFM100 Channel #1 Second Configuration Screen (Two Independent Sensors Mode)104

DSM150 User’s Manual
Page xii Revision 1.4.18
Figure 95 –FPM100 Configuration Screen.......................................................................................106
Figure 96 –FPM100 Advanced Configuration Screen......................................................................107
Figure 97 –FPM100 NMEA 2000®PGN Enable/Disable Screen.....................................................107
Figure 98 –FPM100 Channel #0 First Configuration Screen (Tank Mode)......................................108
Figure 99 –FPM100 Channel #0 Second Configuration Screen (Tank Mode).................................109
Figure 100 –FPM100 Tank Levels Calibration Menu.......................................................................110
Figure 101 –Performing Custom Calibration of the Tank Level Adapter..........................................110
Figure 102 –Tank Levels Calibration Capacity Estimation...............................................................111
Figure 103 –Empty Level Calibration...............................................................................................111
Figure 104 –Intermediate Level Calibration .....................................................................................112
Figure 105 –Full Level Calibration ...................................................................................................112
Figure 106 –Custom Tank Level Calibration Confirmation Screen ..................................................113
Figure 107 –Rectangular Tank Calibration ......................................................................................113
Figure 108 –GPS100 Configuration Screen.....................................................................................115
Figure 109 –GPS100 Advanced Configuration Screen....................................................................116
Figure 110 –Configuring Antenna Altitude on a GPS100.................................................................116
Figure 111 –Configuring Satellite Elevation Mask on a GPS100.....................................................117
Figure 112 –Configuring PDOP Mask on a GPS100 .......................................................................118
Figure 113 –Configuring SNR Mask on a GPS100..........................................................................118
Figure 114 –GPS100 NMEA 2000®PGN Enable/Disable Screen...................................................119
Figure 115 –Restoring Factory Defaults on the GPS100.................................................................120
Figure 116 –Performing a Cold Start of the GPS100.......................................................................120
Figure 117 –Configuring GPS Operating Mode on a GPS100.........................................................121
Figure 118 –Configuring SBAS on a GPS100..................................................................................122
Figure 119 –GPS200 Configuration Screen.....................................................................................123
Figure 120 –GPS200 Advanced Configuration Screen....................................................................123
Figure 121 –GPS200 NMEA 2000®PGN Enable/Disable Screen...................................................124
Figure 122 –Restoring Factory Defaults on the GPS200.................................................................125
Figure 123 –Performing a Cold Start of the GPS200.......................................................................125
Figure 124 –Configuring SBAS on a GPS200..................................................................................126
Figure 125 –IPG100 Configuration Screen......................................................................................127
Figure 126 –IPG100 Advanced Configuration Screen.....................................................................127
Figure 127 –IPG100 N2KServer Information Screen.......................................................................128
Figure 128 –IPG100 Client List Display ...........................................................................................129
Figure 129 –IPG100 Maretron Cloud Services Status Display.........................................................130
Figure 130 –J2K100 Configuration Screen......................................................................................132
Figure 131 –J2K100 Advanced Configuration Screen.....................................................................132
Figure 132 –J2K100 J1939 Diagnostic Messages Configuration.....................................................133
Figure 133 –J2K100 NMEA 2000®PGN Enable/Disable Screen.....................................................134
Figure 134 –J2K100 Engine Instance Configuration........................................................................135
Figure 135 –J2K100 NMEA2000 Transmission Instance Configuration ..........................................135
Figure 136 –J2K100 NMEA2000 AC/Icemaker Instance Configuration..........................................136
Figure 137 –J2K100 J1939 Source Address Configuration .............................................................137
Figure 138 –NBE100 Configuration Screen.....................................................................................137
Figure 139 –NBE100 Advanced Configuration Screen....................................................................138
Figure 140 –RAA100 Configuration Screen.....................................................................................139
Figure 141 –RAA100 Advanced Configuration Menu ......................................................................139
Figure 142 –RAA100 NMEA 2000®PGN Enable/Disable Screen ...................................................140

Revision 1.4.18 Page vi
Figure 143 –RAA100 Label Configuration .......................................................................................141
Figure 144 –RAA100 Rudder Angle Calibration Options .................................................................141
Figure 145 –RAA100 Custom Rudder Angle Calibration .................................................................142
Figure 146 –RAA100 Starboard Rudder Angle Calibration..............................................................142
Figure 147 –RAA100 Center Rudder Angle Calibration...................................................................143
Figure 148 –RAA100 Port Rudder Angle Calibration.......................................................................143
Figure 149 –RAA100 Custom Rudder Calibration Confirmation Screen..........................................144
Figure 150 –RAA100: Setting the Rudder Number..........................................................................145
Figure 151 –RAA100: Setting the Operating Mode..........................................................................145
Figure 152 –RAA100: Setting the + to Sender Gauge Resistance ..................................................146
Figure 153 –RAA100: Setting the –to Sender Gauge Resistance...................................................147
Figure 154 –RIM100 Configuration Screen......................................................................................148
Figure 155 –RIM100 Advanced Configuration Screen.....................................................................148
Figure 156 –RIM100 NMEA 2000®PGN Enable/Disable Screen....................................................149
Figure 157 –RIM100 Channel Configuration Screen .......................................................................150
Figure 158 –SIM100 Configuration Screen......................................................................................151
Figure 159 –SIM100 Advanced Configuration Screen.....................................................................151
Figure 160 –SIM100 NMEA 2000®PGN Enable/Disable Screen ....................................................152
Figure 161 –SIM100 Channel Configuration Screen........................................................................153
Figure 162 - SMS100 Configuration Screen ....................................................................................154
Figure 163 - SMS100 Advanced Configuration Menu......................................................................154
Figure 165 –SMS100 Test Screen...................................................................................................156
Figure 166 –SSC200 Configuration Screen.....................................................................................157
Figure 167 –SSC200 Advanced Configuration Screen....................................................................157
Figure 168 –SSC200 NMEA 0183 Settings Screen.........................................................................158
Figure 169 –SSC200 NMEA 0183 Sentence/Rate Selection Screen...............................................159
Figure 170 –SSC200 Load Default Periodic Rate Selection............................................................159
Figure 171 –SSC200 NMEA 2000®PGN Enable/Disable Screen ...................................................160
Figure 172 –SSC200 Installation Offset Calibration Screen ............................................................161
Figure 173 –Setting the Installation Orientation...............................................................................161
Figure 174 –SSC200 Magnetic Deviation Calibration Start Screen.................................................162
Figure 175 –SSC200 Magnetic Deviation Calibration Progress Screen ..........................................163
Figure 176 –SSC200 Magnetic Deviation Status Screen.................................................................163
Figure 177 –Programming SSC200 Rate of Turn Damping Period..................................................164
Figure 178 –SSC200 Rate of Turn Zero Offset Calibration Screen .................................................164
Figure 179 –Setting Variation Source to NMEA 0183 or NMEA 2000®(factory default)..................165
Figure 180 –Setting Variation Source to NMEA 0183 Only..............................................................165
Figure 181 –Setting Variation Source to NMEA 2000®Only............................................................166
Figure 182 –Entering Manual Variation............................................................................................166
Figure 183 –TLA100 Configuration Screen......................................................................................168
Figure 184 –TLA100 Advanced Configuration Screen.....................................................................168
Figure 185 –TLA100 NMEA 2000®PGN Enable/Disable Screen....................................................169
Figure 186 –Configuring the Tank Capacity.....................................................................................170
Figure 187 –Tank Capacity Change Confirmation Screen...............................................................170
Figure 188 –Performing Custom Calibration of the Tank Level Adapter..........................................171
Figure 189 –Tank Levels Calibration Capacity Estimation...............................................................172
Figure 190 –Empty Level Calibration...............................................................................................172
Figure 191 –Intermediate Level Calibration .....................................................................................173

DSM150 User’s Manual
Page xiv Revision 1.4.18
Figure 192 –Full Level Calibration ...................................................................................................173
Figure 193 –Custom Tank Level Calibration Confirmation Screen ..................................................174
Figure 194 –American Standard Sender Calibration........................................................................174
Figure 195 –European Standard Sender Calibration.......................................................................175
Figure 196 –Configuring the Tank Number......................................................................................175
Figure 197 –Configuring the Tank Type...........................................................................................176
Figure 198 –Configuring the Operating Mode..................................................................................177
Figure 199 –Configuring the + to Sender Gauge Resistance...........................................................177
Figure 200 –Configuring the - to Sender Gauge Resistance ...........................................................178
Figure 201 –TLM100 Configuration Screen.....................................................................................179
Figure 203 –TLM100 NMEA 2000®PGN Enable/Disable Screen....................................................180
Figure 204 –Configuring the Tank Capacity.....................................................................................181
Figure 205 –Tank Capacity Change Confirmation Screen...............................................................181
Figure 206 –Performing Custom Calibration of the Tank Level Monitor...........................................182
Figure 207 –Tank Levels Calibration Capacity Estimation...............................................................183
Figure 208 –Empty Level Calibration...............................................................................................183
Figure 209 –Intermediate Level Calibration .....................................................................................184
Figure 210 –Full Level Calibration ...................................................................................................184
Figure 211 –Custom Tank Level Calibration Confirmation Screen ..................................................185
Figure 212 –Rectangular Tank Selection.........................................................................................185
Figure 213 –Rectangular Tank Calibration ......................................................................................186
Figure 214 –TMP100 Configuration Screen.....................................................................................187
Figure 215 –TMP100 Advanced Configuration Screen....................................................................187
Figure 216 –TMP100 NMEA 2000®PGN Enable/Disable Screen...................................................188
Figure 217 –TMP100 Channel Configuration Screen ......................................................................189
Figure 218 –USB100 Configuration Screen.....................................................................................191
Figure 219 –USB100 Advanced Configuration Screen....................................................................191
Figure 220 –USB100 Device Selection Screen................................................................................192
Figure 221 –VDR100 Configuration Screen.....................................................................................193
Figure 222 –VDR100 Advanced Configuration Screen....................................................................193
Figure 223 –WSO100 Configuration Screen....................................................................................195
Figure 224 –WSO100 Advanced Configuration Screen...................................................................196
Figure 225 –WSO100 NMEA 2000®PGN Enable/Disable Screen..................................................197
Figure 226 –WSO100 Device Label Menu.......................................................................................198
Figure 227 –WSO100 Installation Offset Screen .............................................................................198
Figure 228 –WSO100 Configuration Aborted Due to Low Wind Speed...........................................199
Figure 229 –Installation Offset Success Confirmation Screen.........................................................199
Figure 230 –Installation Offset Abort Confirmation Screen..............................................................200
Figure 231 –Setting the Wind Data Damping Period .......................................................................200
Figure 232 –Setting the Barometric Pressure..................................................................................201
Figure 233 –Setting the Outside Humidity .......................................................................................201
Figure 234 –Setting the Outside Temperature.................................................................................202
Figure 235 –Anchor Watch Display Example...................................................................................203
Figure 236 –Compass Rose Display (Course Up) Example ............................................................205
Figure 237 –Compass Rose (North Up) Display..............................................................................205
Figure 238 –Gauge Display Example ..............................................................................................206
Figure 239 –Rudder Angle Gauge Display Example........................................................................206
Figure 240 –GPS Status Display Example.......................................................................................207

Revision 1.4.18 Page vi
Figure 241 –Numeric Display Example............................................................................................208
Figure 242 –Configuration of Rolling Road Display .........................................................................209
Figure 243 –Rolling Road Display....................................................................................................210
Figure 244 –Line Graph Display ......................................................................................................210
Figure 245 –Weather Display...........................................................................................................211
Figure 246 –Wind Rose Display.......................................................................................................212
Figure 247 –Moon Phase Display....................................................................................................212
Figure 248 –Trim Tab Display..........................................................................................................213
Figure 249 –Swing Meter Display....................................................................................................213
Figure 250 –Tank Gauge Display ....................................................................................................214
Figure 251 –Configuration of Switch/Breaker Display......................................................................214
Figure 252 –Selection of an Individual Switch/Breaker....................................................................215
Figure 253 –Configuration of an Individual Switch/Breaker .............................................................215
Figure 254 –Favorite Screen Showing Highlighted Switch/Breaker.................................................217
Figure 255 –Alert Display.................................................................................................................218
Figure 256 –Adding a New Alert......................................................................................................220
Figure 257 –Part of the Alert Edit Screen ........................................................................................221
Figure 258 –High Alert Parameters..................................................................................................223
Figure 259 –Trigger Configuration –High Alert................................................................................224
Figure 260 –Low Alert Parameters ..................................................................................................225
Figure 261 –Trigger Configuration –Low Alert ................................................................................226
Figure 262 –Trigger Configuration –Data Unavailable Alert............................................................227
Figure 263 –Trigger Configuration –On Alert..................................................................................228
Figure 264 –Trigger Configuration –Data Unavailable Alert............................................................229
Figure 265 –Trigger Configuration Editor –Tripped Alert ................................................................230
Figure 266 –Outside Alert Parameters.............................................................................................230
Figure 267 –Trigger Configuration –Outside Radius Alert ..............................................................231
Figure 268 –Trigger Configuration –Inside Radius Alert .................................................................232
Figure 269 –Trigger Configuration –GPS Quality Alert ...................................................................233
Figure 270 –Direction Alert Parameters...........................................................................................234
Figure 271 –Trigger Configuration –Direction Alert.........................................................................235
Figure 272 –Alert Editor –Time Alert...............................................................................................236
Figure 273 –Remote Annunciator Enable/Disable...........................................................................237
Figure 274 –SMS (Text) Settings... Screen......................................................................................238
Figure 275 –SMS (Text) Phone Number #x Screen.........................................................................238
Figure 277 –Deleting Alert List.........................................................................................................240
Figure 278 –Deleting an Alert: Confirmation....................................................................................241
Figure 279 –Editing an Alert.............................................................................................................241
Figure 280 –Editing an Alert: Alert List.............................................................................................242
Figure 282 –Editing the SMS (Text) Phone Book ............................................................................243
Figure 283 –SMS (Text) Phone Book Screen..................................................................................244
Figure 284 –Phone Number Editing.................................................................................................244
Figure 285 –Editing the Name of a Phone Book Entry.....................................................................245
Figure 286 –SMS Phone Book Test Message Popup......................................................................245
Figure 287 –Advanced Configuration...............................................................................................246
Figure 289 –Surface Mounting Template.........................................................................................256

Revision 1.4.18 Page 1
1 General
1.1 Introduction
Congratulations on your purchase of the Maretron DSM150 NMEA 2000®Multi-function Color
Graphic Display. Maretron has designed and built your display to the highest standards for years of
dependable and accurate service.
Maretron‟s DSM150 is a high-resolution color display that allows easy interpretation of NMEA 2000®
instrument and navigation data through custom display configurations, with an easy-to-use five-key
illuminated keypad.
The Maretron DSM150 is designed to operate within the harsh demands of the marine environment.
However, no piece of marine electronic equipment can function properly unless installed, configured,
and maintained in the correct manner. Please read carefully and follow these instructions for
installation, configuration, and usage of the Maretron DSM150 in order to ensure optimal
performance.
1.2 Firmware Revision
This manual corresponds to DSM150 firmware revision 1.4.18.
1.3 DSM150 Features
The Maretron DSM150 has the following features.
NMEA 2000®Interface
Waterproof NMEA 2000®Connector
Sealed Waterproof Enclosure
Powered Directly from NMEA 2000®Network
Surface Mounting
Backlit Keys
Visual and Audible Alarms
16 User Configurable Favorite Screens (Automatic or Manual Scrolling between Screens)
Capable of Viewing Virtually all NMEA 2000®Information including Batteries, Engines,
Generators, Shore Power, Tanks, Navigation, Weather and More
1.4 Quick Install
Installing the Maretron DSM150 display involves the following four steps. Please refer to the
individual sections for additional details.
Unpack the Box (Section 2.1)
Choose a Mounting Location (Section 2.2)
Mount the DSM150 (Section 2.3)
Connect the DSM150 (Section 2.4)

DSM150 User’s Manual
Page 2 Revision 1.4.18
2 Installation
2.1 Unpacking the Box
When unpacking the box containing the Maretron DSM150, you should find the following items:
1 –DSM150 NMEA 2000®Multi-function Graphic Display
1 –DSM150CABLE-01.0 DSM150 NMEA 2000®1.0m Cable
1 –DSM150 User‟s Manual CD-ROM
1 –Warranty Registration Card
If any of these items are missing or damaged, please contact Maretron.
2.2 Choosing a Mounting Location
The DSM150 is housed in a waterproof enclosure (IEC IP67 rating –protected against the effects of
temporary immersion in water) and can be mounted in either an outdoor location or an indoor
location.
2.3 Mounting the DSM150
The DSM150 can be flush mounted. Maretron suggests a location at which the display can be viewed
from a relatively straight angle, and at which the keys are easily pressed.
2.3.1 Flush Mounting the DSM150
The DSM150 can be directly mounted to any suitable surface. You may choose to secure the
DSM150 to the mounting surface with machine screws or you may use silicone or a similar adhesive
if you do not have easy access to the rear side of the mounting surface. The steps for this type of
mounting are as follows:
1. Attach the Mounting Template (see Section 13) to the surface where the DSM150 is to be
located.
a. Make sure the template is level by using one of the horizontal lines as a guide.
b. Scotch tape works well for securing the template.
2. If securing with machine screws, drill the four mounting holes all the way through the mounting
surface at the locations indicated on the Mounting Template.
a. Use a 4.5mm or 3/16” drill bit.
3. Drill or cut a single hole for the body of the display.
a. Use a 60mm or 2 3/8” hole saw.
4. Remove the template from the mounting surface.
5. Place the DSM150 on the mounting surface, with the body of the DSM150 inserted into the
large hole made with the hole saw. If mounting with silicone adhesive, apply the adhesive to
the portion of the DSM150 that will come into contact with the mounting surface once installed.
6. If mounting with machine screws, insert the screws into the back of the DSM150 and tighten.
a. Use M4-0.7 screws, and ensure that they protrude no more than 5mm into the back
of the DSM150 once mounted.
b. Don‟t over tighten the screws.
c. Do not use threadlocking compounds containing methacrylate ester, such as Loctite Red
(271), as they will cause stress cracking of the plastic enclosure.

Revision 1.4.18 Page 3
2.4 Connecting the DSM150
The Maretron DSM150 provides a connection to an NMEA 2000®interface through a connector that
can be found on the back of the unit. Use the supplied DSM150CABLE-01.0 adapter cable to convert
the 12-pin Deutsch connector on the back of the unit to a standard Micro NMEA 2000®connector.
The NMEA 2000®connector is a five pin male connector (see Figure 1). You connect the DSM150 to
an NMEA 2000®network using a Maretron NMEA 2000®cable (or compatible cable) by first plugging
the female Deutsch connector on the DSM150CABLE-01.0 adapter cable into the connector on the
back of the DSM150 unit, and then connecting the female end of the NMEA 2000®network cable to
the male connector on the DSM150CABLE-01.0 adapter cable (note the key on the male connector
and keyway on the female connector). Be sure the cable is connected securely and that the collar on
the cable connector is tightened firmly. Connect the other end of the cable (male) to the NMEA 2000®
network in the same manner. The DSM150 is designed such that you can plug or unplug it from an
NMEA 2000®network while the power to the network is connected or disconnected. Please follow
recommended practices for installing NMEA 2000®network products.
Figure 1 –NMEA 2000® Connector Face View
2.4.1 Checking the Connection
Once the NMEA 2000®connection to the Maretron DSM150 has been completed, observe the
display to check to see that information is being properly received. One way to verify connectivity is to
enter the device selection menu, which is described in Section 5.2.3.2. Refer to Section 10,
“Troubleshooting”, if no information appears.

DSM150 User’s Manual
Page 4 Revision 1.4.18
3 Operating the DSM150
3.1 Turning the DSM150 On
To turn on the DSM150, press the power key (the leftmost of the five keys on the keypad). The
DSM150 will display a warning and ask you to press the Accept key ( ) to acknowledge the
warning and continue operation of the DSM150 (see Figure 2 below).
Figure 2 –DSM150 Power Up Screen
Alternatively, you may power down the DSM150 by pressing and holding the power key (see Section
3.2 below for details).
3.2 Turning the DSM150 Off
To turn the DSM150 off, press and hold the power key. The DSM150 will display a countdown
screen, which can be seen in Figure 3. If you continue to hold the power key, the DSM150 will power
down in approximately three seconds. If you release the power key before these three seconds have
elapsed, the DSM150 will return to its current operational state.