Marey Aquamatic User manual

Congratulations!
You'vejustpurchasedanewAquamatictanklesswaterheaterandwillsoonbeginto
enjoythebenefitsof“goingtankless.”
Takethe timeto thoroughly read andunderstand this safetyand installation manual
in its entirety before you attempt to install your new Aquamatic tankless water
heater,asitcontainsimportantsafetytipsandinstructions.
Pleasecarefullyread allinstructionsand warnings.Should youhaveany questions,
pleasevisitwww.marey.comforinstallationvideosandFAQ.
Pleasekeepthismanualforfuturereference.
INSTALLING YOUR SHOWER HEATER
INSTALLING YOUR SHOWER HEATER - AQUAMATIC
AQUAMATIC TECHNICAL SPECIFICATIONS
CUSTOMER SERVICE
OTHER PRODUCTS
04
05
06
07
07

0504
1a 1b
23
45
WE ALSO RECOMMEND YOU TO BUY THE
SINGLE FUNCTION SHOWER HEAD
MAREY BRAND
MANERA CORRECTA
CORRECT WAY MANERA INCORRECTA WRONG WAY
AGUA CALIENTE / HOT WATER AGUA FRÍA / COLD WATER
1.Wrapwithteflon:
a)Bothendsofa½"straightnipple(notincluded);
b)Thethreadsontheheateroutput.
2.Screwoneendofthenippleintothebackoftheheater.
3.Screwtheheaterontothepipe, holdingtheheatercover firmly.Tightentheheater
withanadjustablewrench.
4.Screwontheshowerhead.
EXTREMELY IMPORTANT!! DO NOT CONNECTPOWER BEFORE ALLOWING
WATER TO FLOW THROUGH THE SHOWER HEATER FOR 10 SECONDS OR
LONGER. DAMAGE MAY OCCUR TO THE UNIT WHICH COULD INVALIDATE
THEWARRANTY.
Turnfaucetonandallowthewaterrunfor10seconds,thenattachtheshowerhead.
Note:OnlyusetheshowerheadincludedwiththisMarey®Heater.
Damage may occur if a replacement head is installed and this could also void your
warranty.
5.Plugtheheatertoareceptacle*6feetawayfromtheshowerarea.
*30ampelectriccircuitforexclusiveuseoftheheater.DONOTUSE
EXTENSIONS.
CONGRATULATIONSINSTALLATIONISNOWCOMPLETE!
Oncethefaucetisturnedon,hotwaterwillcomeoutinstantly.
AQUAMATIC: SET THE TEMPERATURE BY REGULATING THE FLOW OF
WATERAND/ORBYUSINGTHETEMPERATURESWITCHATTHESIDEOFTHE
UNIT.
I-LOW(Summer)
II-HIGH(Winter)

AQUAMATIC SANTON
POWERPAK PORTABLE POWER GAS
MINI MAREY
06 07
Please visit our website to get to know more about other Marey products.
Temperature increases listed are based on use of the water heater under optimal
conditions with an incoming water temperature of 48ºF. Variable factors such as
incorrect or imperfect installation or warmer incoming water temperature may yield
different results.
Delbrey Street, 211
San Juan, Puerto Rico
00912
www.marey.com
Voltage 110V
Voltage x Amperage = Power 110Vx23,5A=2.6kW
Width x Height x Depth 5" x 7.5" x 3.5"
TECHNICAL SPECIFICATIONS AQUAMATIC
Min./Max. GPM 0.85 - 1.5 GPM
Temperature Control HI & LOW Switch
& Water Pressure
Temperature Increase 110V = 10ºF - 23ºF
4 lbs
220V = 10ºF - 30ºF
220Vx16A=3.5kW
220V
Weight
0.85 - 1.5 GPM
HI & LOW Switch
& Water Pressure
5" x 7.5" x 3.5"
4 lbs
POWER
1
AQUA110
GPM
0.85
1.0
27º
15º
36º
21º
TEMP. INCREASE
PER GPM POWER
2
1.25
1.5
11º
9º
14º
12º
POWER
1
AQUA220
GPM
0.85
1.0
45º
25º
60º
34º
TEMP. INCREASE
PER GPM POWER
2
1.25
1.5
17º
15º
24º
20º
At Marey, we pride ourselves on the excellence of our
customerserviceandsupportteam.
Please feel free to contact us if you have any questions
about our products, warranty service, or if you need
assistance installing a unit. We also strive for continuous
improvement, so we welcome your comments, feedback
andsuggestions.