Markilux IR 54001 Owner's manual

markilux freestanding infrared heater
Information

Type IR 54001
output 1400 watts
Power connection zH05/V032
protection category IP 24
protection class SK I
weight 8.1 kg
Medium operating life infrared lamp about 5000 hours
1 Technical data / power connection
1000
200
95
Ø 350 dimensions in mm
Infrared heater upright unit 1400 watt
Special features
•
• Operation using button control
• Acoustic operation feedback
•
• Infrared halogen lamp with "no glare" heating tube
technology, minimum glare and pleasant light temperature
• Mobile upright unit for even surfaces
• For outdoor areas
• incl. about 2.4 m power cable with Schuko plug
Important INFORMATION: Completely remove the transport protection in the reflector prior to operation.
Establish connection to the mains supply. The house wiring to the power supply must be fused with a circuit breaker of at least 16 A.
The house wiring switch must be switched on for programming and operation. Also see chapter 6 and 7.
Power connection
ttaw0041tinuthgirpuretaehderarfnixulikram
INFORMATION

ttaw0041tinuthgirpuretaehderarfnixulikram
3 Operation
NOTE:
Already in the factory state, the infrared heater is programmed to the operating position (standing upright) and without timeout.
On switching on the infrared heater operation is confirmed with acoustic signals.
The heating output can be detected with a delay on switching on.
According to the timeout programming, the following will be carried out:
Outside the programming, the infrared heater can be switched on for 5 minutes by double clicking the device button (signal tone) and
• 1 Signal tone ˋwithout timeout
• 2 Signal tones ˋ30 minutes operating time
• 3 Signal tones ˋ60 minutes operating time
• 4 Signal tones ˋ90 minutes operating time
Short-term heating
2 Maximum infra-red radiation intensity
infra-red radiation intensity. Included are here at
the radiation areas and the respective max. radiation
intensity.
205 W/m²
75 W/m²
118 W/m²
53 W/m²
1,5 m
2,0 m
2,5 m
3,0 m
2,1 m
2,8 m
3,5 m
4,2 m
m8,1
m3
,2
m7,2
m1,3
INFORMATION

4 Programming the timeout
It is important that damaged device elements such as connecting cable, switch, sealing collar or heating tube must be replaced. The
infrared heater must be dismantled immediately and stored in a dry place. Repairs (replacing a defective connecting cable, a defective
heating tube or similar) must only be carried out by the manufacturer.
Heating tubes are sensitive to direct skin contact (do not touch with your fingers). Grease or other contamination can be cleaned with a
cloth soaked in alcohol.
specialist dealer.
any detergents). Never immerse the infrared heater in or spray with liquids.
An eventual discolouration of the protective grating due to heat exposure results from normal physical processes and does not
constitute a defect.
Switch on the infrared heater only when all cable connections have been established completely.
The heating tube must be protected from mechanical stress. Is must be replaced when changes (dark spots, deformations) become
visible or if the nominal service life has been reached.
Important NOTE:
Place the infrared heater on a level surface and connect to the mains supply.
Activating the programming:
Press the device button for 5 seconds until you hear a long signal tone (2 sec.).
Programming the timeout:
30 min First double click ˋ30 minutes operating time ˋ2 Signal tones
60 min Second double click ˋ60 minutes operating time ˋ3 Signal tones
90 min Third double click ˋ90 minutes operating time ˋ4 Signal tones
no Fourth double click ˋno timeout ˋ1 Signal tone
Completion of programming:
Press the device button for 5 seconds until you hear a long signal tone (2 sec.).
5 Repair / maintenance and cleaning
The factory state is without timeout for upright operation.
NOTE:
If you hear three short signal tones in sequence, the upright operating position must be re-programmed by pressing again (2 sec.) and
releasing the device button. You will hear a long signal tone (2 sec.).
ttaw0041tinuthgirpuretaehderarfnixulikram
INFORMATION