Marshall Electronics V-LCD173HR User manual

Broadcast A/V Division
V-LCD173HR
___________________________________________________________________________________
17.3” Professional LCD Rack Mount / Desktop Monitor
USER MANUAL

V-LCD173HR Manual
Marshall V-LCD173HR 2
Table of Contents
1. Introduction, Installation, and Setup.......................................................................................……………..…….....3
2. Panel Features........................................................................................................................…………..………....3
3. Navigation Main Menu……………………………….........................................……….……………..........................5
3.1 Main Menu……………….…………………………………………………..……………...…………………………5
3.2 Video Configuration……………….………………………………………………….…………………….…………5
3.3 Marker Configuration………………………………………………………..……….………….………………….…6
3.4 Display Configuration………………………………………………………….……………………….……………..7
3.5 Function Configuration………………………………………………………………………….…….…………..…..8
3.6 Audio Configuration………………………………………………………………………………………….……..…9
3.7 System Configuration…………………………………………………………………………………….………..….9
4. Specifications………………………………………………………………………………………………………….…...10
5. Dimensions…………....................................................................................……………………............................13
6. Monitor Care…………………………………………………………………………………………………………..……13
7. Warranty...............................................................................................................................………………..….....14
IMPORTANT SAFETY INSTRUCTIONS:
The V-LCD173HR 17.3” LCD Monitor has been tested for conformance to safety regulations and requirements
and has been certified for international use. However, like all electronic equipment, the V-LCD173HR should be
used with care. Please readandfollow the safetyinstructions toprotect yourself from possible injuryandto minimize
the risk of damage to the unit.
• Follow all instructions and warnings marked on this unit.
• Do not attempt to service this unit yourself, except where explained in this manual.
• Provide proper ventilation and air circulation and do not use near water.
• Keep objects that might damage the device and assure that the placement of this unit is on a stable surface.
• Use only the power adapter and power cords and connection cables designed for this unit.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

V-LCD173HR Manual
Marshall V-LCD173HR 3
1. Introduction, Installation and Setup ______________________________________________
■Introduction and Installation
The V-LCD173HR 17.3” LCD Monitor can be mounted in any standard EIA 19” equipment rack. The attached rack ears can
be angled to provide the user control over the viewing angle. Adequate ventilation is required when installed to prevent possible
damage to the monitor’s internal components. Both VESA standard 75mm and 100mm hole pattern allow for custom mounting
installations.
■Package Contents
• 1x V-LCD173HR 17.3” LCD Monitor
• 1x DC Adapter
• 1x TALLY Connector
NOT INCLUDED:
• Optional Marshall “V-ST15” base mount for desktop use
• (4) M4 screws needed to install “V-ST15” base mount
■Connections, Power-On, and Initial Setup
Plug the power supply into an AC power source. Attach the power connector to the back of the monitor. Connect the required
cables for video signal input and output. (Power must be supplied to the V-LCD173HR to activate the loop-though output.) The
monitor defaults to ‘ON’ when power is supplied. Choose the desired signal source by selecting the “SDI”, “HDMI” or “VIDEO”
button on the front bezel.
2. Panel Features _____________________________________________________________
Top and Front Panel Features
1 – Rack Mount Ears: Use rack mount ears to mount 6RU
racks or other display applications.
5 – Video Buttons: Indicator lights up when signal
switches to VIDEO state.
2 – SDI Button: Indicator lights up when signal switches to
SDI state.
6 – Menu Navigation Knob: Turn first for Volume,
Brightness, etc or press first for Main Menu.

V-LCD173HR Manual
Marshall V-LCD173HR 4
3 – HDMI Button: Indicator lights up when signal switches
to HDMI state.
7 – Headphone Jack: Standard 3.5mm stereo mini-
phone plug can be used.
4 – User-Definable Function Buttons: Functions can be
customized by pressing any User button for 3-5 seconds.
These user-definable function buttons are assigned using
the on-screen direct access menu.
Default User Function Options:
F1: Aspect Ratio F2: Histogram F3: False Color
8 – Power Button: Use the power button to switch the
screen ON and OFF.
Rear Panel Features
1 – USB Interface: Only for program upgrades. NOT to be
used for non-professional use.
5 – Analog Audio “RCA” Connectors: Left and right
audio inputs are active when “Video” is selected as the
video source. This audio may be monitored at the
headphone jack connection.
2 – Tally Input Connector: The LED tally can be
activated by connecting the corresponding pin to ground.
A variety of external devices can be used to perform the
contact closure. No additional power should be supplied to
the HD-15 port. See pinout guide next to connector.
6 – HDMI Digital Video Connectors: HDMI video input
and loop output. Embedded audio may be monitored at
the headphone jack connection and visually monitored
on-screen.
3 – Serial Digital “BNC” Connectors: SDI input and loop
output are compatible with SDI, HDSDI and 3GSDI inputs.
Embedded audio may be monitored at the headphone jack
connection and visually monitored on-screen.
7 – 4-Pin Power Connector:
To be used with 12-volt power supplies only.
Caution: 24 volts 4-pin power supplies are NOT
compatible with this monitor. Please check label on
the power supply before connecting.
4 – Composite Analog “BNC” Connectors: Video input
and loop output are used for NTSC or PAL composite
(CVBS) video sources.
8 – VESA 75mm and 100mm Hole Patterns: VESA-
standard hole-patterns (75mm and 100mm) are
provided to accommodate a variety of custom
mounting options.

V-LCD173HR Manual
Marshall V-LCD173HR 5
3. Navigation Menu_____________________________________________________________
Main Menu: Push the MENU control button on the monitor to adjust the function configurations. To change configurations,
select a configuration from the main menu by turning the knob and pressing the menu button once to select. Edit configuration
by turning knob to change levels, then press menu button again to confirm the changes. Repeat with each selection as
needed.
3.1 Main Menu Navigation
Press the MENU knob on the monitor and function menus will pop-up on the screen. Rotate left or right
to select an option. Then press the knob again to open the selection. When an arrow pointer appears in
the menu, turn the Menu knob again to access the item or to confirm a selection.
3.2 Video Configuration Submenu
ITEMS
OPTIONS
Video Configuration
Exit
Brightness
0 – 100 (50 is default)
Contrast
0 – 100 (50 is default)
Saturation
0 – 100 (50 is default)
Sharpness
0 – 100 (0 is default)
Color Temp (White Bal)
6500K, 7300K, 9300K, User

V-LCD173HR Manual
Marshall V-LCD173HR 6
Color Temp R
0 – 255
Note: These three items
appear when “User” mode
is selected.
Color Temp G
0 – 255
Color Temp B
0 – 255
■ Brightness
The Brightness level ranges from 0 to 100.
■ Contrast
The Contrast level ranges from 0 to 100.
■ Saturation
The Saturation level ranges from 0 to 100.
■ Sharpness
The Sharpness level ranges from 0 to 100.
■ Color Temp
Choose one of three color temperature presets (6500K, 7300K or 9300K) or define the color with the USER mode.
3.3 Marker Configuration Submenu
■Marker Enable
Turn ‘ON’ to display a Marker Enable on the screen.
■ Center Marker
Turn ‘ON’ to display a Center Marker on the screen.
ITEMS
OPTIONS
Marker Configuration
Exit
Center Marker
OFF, ON (OFF is default)
Aspect Marker
OFF, 4:3, 14:9, 13:9, 15:9, 1.85:1, 2.35:1
(OFF is default)
Safety Marker
OFF, 95%, 93%, 90%, 88%, 85%, 80% (OFF
is default)
Marker Color
Red, Green, Blue, White, Black (Red is
default)
Marker Mat (background)
OFF, 1– 7 (1 is default)
Thickness
1, 2, 3, 4, 5, 6, 7 (2 is default)

V-LCD173HR Manual
Marshall V-LCD173HR 7
■ Aspect Marker
Set the Aspect Marker on the screen. Options: OFF, 4:3, 14:9, 13:9, 15:9, 1.85:1, 2.35:1.
■ Safety Marker
Use this to superimpose one of 6 Safety Markers on the screen. Options: OFF, 95%, 93%, 90%, 88%, 85%, 80%.
■ Marker Color
Choose from 5 Marker Colors: Red, Green, Blue, White, or Black.
■ Marker Mat (marker background)
Choose the Marker Mat transparency. Options: OFF,1-7.
■ Thickness
Choose the Marker Line Thickness ranging from 1 to 7.
3.4 Display Configuration Submenu
ITEMS
OPTIONS
Display Configuration
Exit
Aspect Ratio
16:9, 4:3 (16:9 is default)
Check Field
OFF, Mono, Red, Green, Blue (OFF is default)
Scan
Full Screen, Overscan, Underscan, Pixel-to-Pixel
(Full Screen is default)
Image Flip
OFF, H, V, H/V (OFF is default)
Freeze Input
OFF, ON (OFF is default)
■ Aspect Ratio
Option to switch between 16:9 and 4:3 Aspect Ratio.
■ Check Field
Use these modes for monitor calibration or for individual color component image analysis. In Monochrome mode, color
is disabled and grayscale image is shown. In Blue, Green, and Red Check Field modes, only the selected color is shown.
■ Scan
Use to enable the Scan mode. Options: Full screen, Overscan, Underscan, Pixel-to-Pixel.
■ Image Flip
Select to enable Image Flip mode. Options: OFF, H (Horizontal), V (Vertical), H/V (Horizontal and Vertical).

V-LCD173HR Manual
Marshall V-LCD173HR 8
■Freeze Input
Turn ‘ON’ to enable Freeze Input mode. A still image will remain on the screen until Freeze is turned off or power is
removed from the monitor.
3.5 Function Configuration Submenu
ITEMS
OPTIONS
Function Configuration
Exit
Peaking
OFF, ON (OFF is default)
Peaking Color
Red, Green, Blue, White, Black (Red is default)
Peaking Level
0 – 100 (50 is default) Note: This option is
disabled when Peaking is set to OFF.
False Color
OFF, ON (OFF is default)
Exposure
ON, OFF (OFF is default)
Exposure Level
0 – 100 (15 is default) Note: This option is
disabled when Exposure is set to OFF.
Histogram
OFF, Y, RGB, Color (Y is default)
DSLR Scale
OFF, ON (Available for HDMI input only.)
■ Peaking
Turn ‘ON’ to enable Peaking mode.
■ Peaking Color
When Peaking Mode is enabled, the monitor will add color to sharply defined edges and objects in an image. This is
intended as a tool to aid in judging sharp camera focus. When a camera is adjusted for best focus, the object of interest
will have colored edges. Choose from 5 Peaking Colors: Red, Green, Blue, White, or Black. Normally, this function is
turned on only as long as needed for focus adjustment and then turned off for normal monitor operation.
■ Peaking Level
The Peaking Level ranges from 0 to 100.
■ False Color
Turn ‘ON’ to enable False Color mode. When this is on, the picture will have colors added based on video level. It is
useful to make a quick check to see if level exceed normal black and white limits or to make a comparison between one
scene or lighting situation and another.

V-LCD173HR Manual
Marshall V-LCD173HR 9
■ Exposure
Turn ‘ON’ to enable Exposure Level mode.
■ Exposure Level
The Exposure Level setting ranges from 0 to 100. This function mimics the “zebra pattern” display that is often used in
many camera viewfinders. It provides a quick check for proper camera exposure. When it is turned ON, diagonal lines
will appear in the image areas where the brightness matches the level Exposure Level setting. This is useful when a
camera angle has been changed and it is important to keep certain objects at the same brightness. On a typical video
scale of 0 – 100, the Exposure number relation is shown in the table below. That is, “zebra patterns” appearing on the
image indicates that the area covered by the zebra pattern matches or exceeds the selected video level.
EXPOSURE
LEVEL NUMBER
APPROXIMATE
VIDEO LEVEL
15
100%
40
90%
70
80%
100
70%
■ Histogram
Use to enable the Histogram mode. Options: OFF, Y (shown), RGB (with color), Color (RGB colors individually shown).
The Histogram display is similar to displays used in DSLR cameras and desktop color processing applications. It
provides a graphic representation of the amount of dark, mid and light tones in an image. It is useful for comparing the
average “balance” between different “real” images, not test patterns.
■ DSLR SCALE (HDMI Input Only)
Turn ‘ON’ to enable DSLR Scale mode.
3.6 Audio Configuration Submenu
ITEMS
OPTIONS
Function Configuration
Exit
Audio
0 – 100 (50 is default)
■Audio
The Audio level ranges from 0 to 100.
3.7 System Configuration Submenu

V-LCD173HR Manual
Marshall V-LCD173HR 10
ITEMS
OPTIONS
System Configuration
Exit
Language
English, Chinese (English as default)
HDMI/SDI Convert
OFF, ON (OFF as default)
Menu Timer
10s, 20s, 30s (10s as default)
Back Light
0 – 100 (100 as default)
Reset
OFF, ON
ISP
Firmware Version
V3.3
■ Language
Choose Language: English or Chinese.
■ HDMI/SDI Convert
Turn ‘ON’ to enable HDMI/SDI Convert mode.
■ Menu Timer
The menu timer level ranges from10s, 20s, 30s.
■ Back Light
The Back Light level ranges from 0 to 100. Back Light adjustment is commonly used to
compensate for ambient light levels in the viewing environment and is preferred over using
Contrast and Brightness for this.
■ Reset
Turn ‘ON’ to enable reset mode.
■ISP
ISP is for service use only.
■Firmware Version
Display firmware version (V3.3 at the time this manual was prepared).
4. Specifications_______________________________________________________________
Model Name
V-LCD173HR
Role of Usage
17.3” LCD Monitor

V-LCD173HR Manual
Marshall V-LCD173HR 11
Connectors
Inputs
• SDI BNC x 1 with Loop Out
• HDMI x 1 with Loop Out
• Composite BNC x 1 with Loop Out
• Audio L/R RCA x 2 Line Level
• Tally HD-15 Pin compatible with GPI open collector or contact closure to ground/earth
• USB 3.0 USB-A x 1 (Firmware Updates)
• XLR-12V 4 pin x 1
Outputs
• 3.5 mm Front Panel Stereo Headphone Jack
Hardware
• Included Rack Ears x 2 (6RU height) for standard 19” rack mount
• Back Panel Supports VESA 100x100mm and 75x75mm mounting systems
• Optional Desktop Stand Model V-ST15 Available
• Weight 7.9 lbs. (3.6 Kg)
• Product Dimension: 1.29” x 17.75” x 10.5” / 3.28cm x 45cm x 26.7cm (D x L x W)
Panel Information
• Native Resolution:1920x1080 pixels
• Contrast Ratio: 700:1
• Luminance: 300 nits
• Display colors: 16 million colors
• Viewing Angle: 178-degrees H & V
Supported Formats / Frame Rates
Composite Input
• NTSC
• PAL
SD-SDI Input
• 480i 59.94Hz
• 576i 50Hz
HD-SDI
• 720p 25, 29.97, 30, 50, 59.94, 60 Hz
• 1080i 50, 59.94, 60 Hz
• 1080psf 23.98, 24.00 Hz
• 1080p 23.98, 24, 25, 29.97, 30 Hz
3G-SDI
Level A
• 1080p 50, 59.94, 60 Hz
• 10800i 50, 59, 60 Hz
• 1080psf 23, 24, 25, 29.97, 30 Hz
• 1080p 23.98, 24, 25, 29.97, 30 Hz
SD - HDMI
• 480i 59.94, 60 Hz
• 576i 50 Hz
• 480p 59.94, 60 Hz
• 576p 50Hz
HD - HDMI
• 720p 25, 29.97, 30, 50, 59.94, 60 Hz
• 1080i 50, 59.94, 60 Hz
• 1080psf 23.98, 24 Hz
• 1080p 23.98, 24, 25, 29.97, 30 Hz

V-LCD173HR Manual
Marshall V-LC173HR 12
3G - HDMI
• 1080p 50, 59.94, 60 Hz
PC - HDMI
• 800 x 600 56, 60 Hz
• 1024 x 768 60 Hz
• 1152 x 864 60 HZ
• 1280 x 720 50, 59, 60 HZ
• 1280 x 768 60 HZ
• 1280 x 800 60 HZ
• 1680 x 1050 59, 60 HZ
• 1600 x 1200 60 HZ
• 1920 x 1080 50, 59, 60 HZ
HDMI < > SDI Cross Conversions
SD
• 480i 59.94 Hz
• 576i 50 Hz
HD
• 720p 25, 29.97, 30, 50, 59.94, 60 Hz
• 1080i 50, 59.94, 60 Hz
• 1080psf 23.98, 24 Hz
• 1080p 23.98, 24, 29.97,30 Hz
3G
• 1080p 50, 59.94, 60 Hz
Electrical
In Power On
• 18.48W
• 1.54A
• 12V
In Stand-By
• 4.68W
• 0.39A
• 12V
5. Dimensions_________________________________________________________________

V-LCD173HR Manual
Marshall V-LC173HR 13
6. Monitor Care________________________________________________________________
Screen Cleaning
Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro-fiber
cloth can also be used with only non-abrasive and ammonia-free cleaning agents. Do not use paper towels. Paper towel
fibers are coarse and may scratch the surface of the polycarbonate faceplate or leave streaks on the surface. Antistatic and
fingerprint resistant cleaning agents are recommended. Do not apply excessive pressure to the screen to avoid damaging
the LCD.
Faceplate Dusting
Dust the unit with a soft, damp cloth or chamois. Dry or abrasive cloths may cause electrostatic charge on the surface,
attracting dust particles. Neutralize static electricity effects by using the recommended cleaning and polishing practice.
7. Warranty ___________________________________________________________________
Marshall Electronics warranties to the first consumer that this V-LCD173HR 17.3” LCD Monitor will, under normal use, be
free from defects in workmanship and materials, when received in its original container, for a period of one year from the
purchase date. This warranty is extended to the first consumer only, and proof of purchase is necessary to honor the warranty.
If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty
set forth above. Therefore, labor and parts may be charged to the consumer. This warranty does not apply to the product
exterior or cosmetics. Misuse, abnormal handling, alterations or modifications in design or construction void this warranty. No
sales personnel of the seller or any other person is authorized to make any warranties other than those described above, or
to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period described above.
Note: Due to constant effort to improve products and product features, specifications may change without prior notice.

V-LCD173HR Manual
Marshall V-LC173HR 14
MarshallElectronics,Inc.
20608 Madrona Avenue, Torrance, CA 90503
Tel: [phone] • Fax: [phone]
www.LCDracks.com
[e-mail]