Martin Tripix User manual

Tripix™
user manual

Dimensions
All dimensions are in millimeters
Tripix™300 / Tripix™1200
Tripix Power™
©2009-2010 Martin Professional™ A/S. Information subject to change without notice. Martin Professional A/S
and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or
economic loss or any other loss occasioned by the use of, inability to use or reliance on the information
contained in this manual. The Martin logo, the Martin name and all other trademarks in this document
pertaining to services or products by Martin Professional A/S or its affiliates and subsidiaries are trademarks
owned or licensed by Martin Professional A/S or its affiliates or subsidiaries. The use of certain patents in
Martin™ Tripix™ products is licensed by Color Kinetics, Inc. (see details printed on product)
P/N 35000232, Rev. F

Safety Information
Warning! Read the safety precautions in this section before
installing, powering, operating or servicing this product.
The following symbols are used to identify important safety information
on the product and in this manual:
Warning! Do not view the light output with optical instruments or
any device that may concentrate the beam.
This product is for professional use only. It is not for household use.
This product presents risks of severe injury or death due to fire hazards,
electric shock and falls.
Read this manual before installing, powering or servicing the product,
follow the safety precautions listed below and observe all warnings in
this manual and printed on the fixture. Install and operate the fixture
only as described in this manual and in accordance with local laws and
regulations. Refer any operation not described in this manual to a
qualified technician.
If you have questions about how to operate the fixture safely, please
contact your Martin dealer or call the Martin 24-hour service hotline at
[phone], or in the USA on 1-888-tech-180.
DANGER!
Safety hazard.
Risk of severe
injury or death.
Warning!
Hazardous
voltage. Risk
of lethal or
severe electric
shock.
Warning!
LED light
emission.
Risk of eye
injury.
Warning!
Burn hazard.
Hot surface.
Do not touch
Warning!
Refer to user
manual.

PROTECTION FROM ELECTRIC SHOCK
•Shut down power to the entire installation at the main power
distribution board and lock out power (by removing the fuse for
example) before carrying out any installation or maintenance work.
•Disconnect the fixture from AC power before removing or installing
any cover or part and when not in use.
•Connect the Tripix Power electrically to ground (earth).
•Use only a source of AC power that complies with local building and
electrical codes and has both overload and ground-fault (earth-fault)
protection.
•Before using the devices, check that all power distribution equipment
and cables are in perfect condition, are rated for the current
requirements of all connected devices.
•Isolate all devices from power immediately if any cable, seal, cover or
other component is damaged, cracked or deformed. Do not reapply
power until repairs have been completed.
•The Tripix Power is for indoor use only.
•Refer any service operation not described in this manual to an
authorized Martin Service partner.
PROTECTION FROM BURNS
•Do not operate the devices if the ambient temperature (Ta) exceeds
45° C (113° F).
•The exterior of the fixtures and Tripix Power becomes hot, up to 65° C
(149° F) during normal operation. Ensure that accidental physical
contact with the devices is impossible.
•Allow the fixture to cool for 5 minutes before servicing.
•Keep combustible materials (for example fabric, wood, paper) at least
20 cm (8 in.) away from the devices.
•Keep flammable materials well away from the devices.
•Do not modify the Tripix Power or fixtures in any way not described in
this manual or install other than genuine Martin parts.
•Use only Martin approved accessories to mask or modify the light
beam.
•Do not attempt to bypass fuses. Replace defective fuses with ones of
the specified type and rating only.
•Install the strips outdoors and the Tripix Power indoors in a well-
ventilated area only. Provide a minimum clearance of 5 cm (2 in.) and
ensure unrestricted airflow around Tripix Power and the fixtures.

PROTECTION FROM INJURY
•Do not look at LEDs with a magnifying glass or any other optical
instrument that may concentrate the light output.
•Ensure that all external covers, components and installation fittings
are securely fastened.
•Block access below the work area and work from a stable platform
whenever installing, servicing or moving the devices.
•Ensure that all supporting structures, surfaces, fasteners and lifting
equipment can bear the weight of all the devices they are intended to
support plus an adequate safety margin, and that they conform to
local building and safety regulations.
•Use a sufficient number of fasteners with sufficient corrosion
resistance, dimensions and strength to mount the DIN rail safely. Any
nuts used must be self-locking.
Disposing of this product
Martin™ products are supplied in compliance with Directive
2002/96/EC of the European Parliament and of the Council of
the European Union on WEEE (Waste Electrical and Electronic
Equipment), as amended by Directive 2003/108/EC, where
applicable.
Help preserve the environment! Ensure that this product is
recycled at the end of its life. Your supplier can give details of
local arrangements for the disposal of Martin products.

Contents
Dimensions....................................................................................................... 2
Safety Information............................................................................................. 3
Contents........................................................................................................... 6
Introduction....................................................................................................... 7
Unpacking ................................................................................................. 8
Using for the first time................................................................................ 8
Physical installation .......................................................................................... 9
Location and orientation ............................................................................ 9
Mounting.................................................................................................. 10
Connections - general..................................................................................... 14
Connection overview ............................................................................... 14
AC power........................................................................................................ 15
Connecting to power................................................................................ 16
Installation setup............................................................................................. 17
Fixture configuration....................................................................................... 23
Configuring for DMX control .................................................................... 23
Configuring for stand-alone operation ..................................................... 26
Operation........................................................................................................ 31
DMX color control modes ........................................................................ 31
Service and maintenance............................................................................... 33
Cleaning .................................................................................................. 33
Fixture information and monitoring.......................................................... 34
Testing.....................................................................................................35
Fuse replacement.................................................................................... 35
Software installation ................................................................................ 36
Troubleshooting.............................................................................................. 37
Specifications ................................................................................................. 38

7 Tripix user manual
Introduction
Thank you for selecting Tripix™, a compact IP66-rated LED-based
color-changing striplight from Martin™. The Tripix is available in short
300 mm (11.8 inch) and long 1200 mm (47.2 inch) models. Both
fixtures are powered by the Tripix Power™.
Diffuser filters that give wider beam angles are available from Martin.
This product features:
•RGB (red, green, blue) color mixing, with raw and calibrated RGB
plus calibrated HSI and HSIC (hue, saturation, intensity, color
temperature) color control options
•81 W LED power and 1440 lumens total output (at narrow beam
angle) from Tripix 1200
•24 W LED power and 360 lumens total output (at narrow beam angle)
from Tripix 300
•Tripix Power can drive up to twenty-four Tripix 300s or six Tripix
1200s, or any mixture of Tripix 300 and Tripix 1200 devices that not
exceed 7.2 meters (23 ft. 7 in.)
•Possibility of controlling all fixtures attached to an Tripix Power as one
single RGB, HSI or HSIC pixel
•One Tripix 1200 fixture can be controlled as four single RGB pixels
•DMX 512A control
•Clamp mounting system for standard 35 mm DIN rail
•64 built-in stand-alone programs
•Master/slave functionality with 64 pre-programmed stand-alone
shows available
For the latest firmware updates, documentation, product specifications
and other information about this and all Martin Professional™ products,
please visit the Martin website at http://www.martin.com

8 Tripix user manual
Unpacking
The following items are included with the Tripix fixture:
•300 mm or 1200 mm strip light fixture with narrow beam angle diffuser
installed
•Warning note
•Two short DIN rails
The following items are included with the Tripix Power:
•Tripix Power device
•Tripix Power Inserter cable
•This user manual
•DMX termination plug
•Two AC mains power cables (EU with Schuko plug, US without plug)
Using for the first time
Before applying power to the fixture:
•Carefully review “Safety Information” on page 3
•Check that the local AC power voltage is within the range listed on the
Tripix Power serial number label
•Install the Tripix Power and Tripix fixtures as described in this manual

9 Tripix user manual
Physical installation
Warning! Read "Safety Information" on page 3 before installing
the devices.
The safety and suitability of lifting equipment, installation location,
anchoring method, mounting hardware and electrical installation
is the responsibility of the installer. All local safety regulations
and legal requirements must be observed when installing and
connecting the devices. Installation must be carried out by
qualified professionals only.
The Tripix fixtures must be clamped onto a DIN top-hat rail that is
securely anchored to a suitable flat surface. Ensure that the supporting
structure can bear the weight of all installed devices plus an adequate
safety margin.
Make sure that there will be at least 5 cm (2 in.) of free space and
unrestricted airflow around both the Tripix Power and the Tripix fixture.
Warning! Do not use the Tripix fixture without a diffuser filter
installed.
Contact your Martin supplier for assistance if you have any questions
about how to install this product safely.
Location and orientation
The Tripix fixtures are for outdoor installations with an IP rating of 66
while Tripix Power is for indoor use only;
•Do not bury the devices or locate them in a space that is more critical
than IP66.
•Allow 5 cm (2 in.) free space around both the Tripix Power and the
Tripix fixtures.
•Install the Tripix Power and the Tripix fixtures at least 20 cm (8 in.)
away from any combustible materials (wood, paper, etc.) and well
away from any flammable materials.
•The housings of the Tripix fixture and the Tripix Power reach
temperatures up to 65° C (149° F). Restrict public access or locate
the devices so that they cannot accidentally be touched.

10 Tripix user manual
Mounting
DIN rail
The Tripix fixture is designed for mounting on standard 35 mm top-hat
DIN rail. You can use the standard 35mm DIN Rail or use the Short
Martin DIN rail 35mm for a more comfortable installation.
Figure 1: Short Martin DIN rail 35mm
Dimensions for the DIN rail supplied by Martin are given in Figure 1.
Note that you cannot fasten the Tripix fixture mounting clamps directly
over screws used to fasten DIN rail to the mounting surface. If a DIN
rail mounting screw is in the way of a mounting clamp, move it to
another slot in the DIN rail.
Note that you must install extra screws through the DIN rail into the
mounting surface to secure fixtures in vertical installations (see
“Mounting the Tripix fixture vertically” on Page 11).
Mounting the Tripix fixture
Warning! The Tripix fixture must be mounted on a top-hat profile
35 mm (1.4 inch) DIN rail that is securely anchored to a surface.
The installation must conform to local electrical, building, safety
and fire regulations. If there is a danger that the fixture may cause
injury or damage if it falls, use a means of secondary attachment
such as safety cables looped around the fixture.
The short DIN rail from Martin (P/N 23819560) is just long enough to
allow two Tripix fixtures to be mounted end-to-end.

11 Tripix user manual
To mount the fixture on a surface using 35 mm DIN rail:
1. Fasten the DIN rail securely to the mounting surface.
2. See Figure 2. The fixture mounting bracket has a hooked profile on
one side (see A). Hook this profile over the top of the DIN rail and
swing the bracket down. Use a 2.5 mm Allen key to tighten the
mounting clamp screw (see B).
(A) (B)
Figure 2: Mounting on DIN rail
Mounting the Tripix fixture vertically
The mounting clamp screws will not hold the product securely on the
DIN rail if fixture is installed vertically. You must therefore insert screws
in the mounting surface through the DIN rail mounting holes (see
Figure 3) so that the fixture mounting clamps rest against these screws
and secure the fixture.
Figure 3: Vertical mounting on DIN rail

12 Tripix user manual
Adjusting tilt angle
The Tripix fixture can be tilted through 105°.
Figure 4: Tilt angle
To adjust the tilt angle:
1. See
Figure 5. Turn the locking knob clockwise until it releases the
fixture profile.
2. Adjust the fixture to the desired tilt angle
3. Rotate the locking knob counter-clockwise until it engages in the
fixture profile and locks it in position.
Lock Unlock
Figure 5: Releasing and tighten the tilt locking lock

13 Tripix user manual
Mounting the Tripix Power
The Tripix Power conforms to IP20 and is for indoor use only. Fasten
the Tripix Power securely to a flat surface in a location that is
accessible for service. To mount it, use M5 screws in the four mounting
holes.
Respect all local safety, fire and building regulations governing the
installation of electrical equipment in cavities and plenums. Do not
expose to moisture. Allow free airflow and at least 5 cm (2 in.) of free
space around the device. Allow sufficient ventilation to ensure that the
ambient temperature will not exceed 40° C (104° F).

14 Tripix user manual
Connections - general
Tripix fixtures have cable tails with 13-pin DIN connectors that are
waterproof to IP66 for combined data and power interconnection. The
connector clip rings provided must be screwed onto connectors until
two clicks have been heard to lock connectors together and ensure a
permanent waterproof seal.
Connection overview
Figure 6 gives an overview of system layout and cable connections:
Figure 6: Schematic cable and device layout
Warning! Do not exceed the maximum permitted number of
fixtures per Tripix Power output channel, i.e. 24 Tripix 300 fixtures
or 6 Tripix 1200 fixtures or the mixture of Tripix 300 and Tripix
1200 fixtures that not exceed 7.2 meters for one Tripix Power.
DMX
Out In
Power
DMX
Tri
p
ix Powe
r
DMX
termination
plug

15 Tripix user manual
AC power
Warning! Read “Safety Information” on page 3 before attempting
to install this product. Lock out power to the entire installation
before working on cables and connections or removing any cover.
Warning! The Tripix Power is switch-selectable within the ranges
100-120 and 200-240 VAC nominal, 50/60 Hz. Do not connect to
power at any other voltage or frequency. Check that the switch is
correctly positioned to match the local voltage as described in the
Tripix Power user manual before connecting to power.
Warning! Electrical installation must be carried out by qualified
professionals only.
Warning! The electrical equipment and cable used to supply the
Tripix system with power must be in perfect condition, be
adequately dimensioned for current requirements and respect
maximum cable run lengths.
Warning! For protection from dangerous electric shock, the Tripix
Power must be grounded (earthed). The AC power distribution
system must be fitted with current overload and ground-fault
(earth-fault) circuit breakers as well as a means to isolate the
Tripix Power from power and lock out power during service.
Important! Do not connect the Tripix system to an electrical
dimmer system. Doing so can damage the electronics.
If you require help in planning or dimensioning the power distribution
system, please contact your Martin supplier for assistance.
If there is a break or cut at any point in a cable (for example at a
connection point), and if this is exposed to water, moisture can be
drawn up the inside of the cable due to the vacuum effect of
temperature fluctuations during operation.
The Tripix Power is protected by a 6.3 amp slow-blow primary fuse
located on the Tripix Power.

16 Tripix user manual
Connecting to power
The Tripix Power is supplied with an IEC power cable ready for
connection to a single-phase 3-wire (live, neutral, ground/earth) power
distribution system. The Tripix Power has a switch that must be
correctly set to match the local voltage in the ranges 100-120 and 200-
240 VAC nominal, 50/60 Hz.
The Tripix Power has one output channel which can drive up to twenty-
four Tripix 300s or six Tripix 1200s, or a mixture of Tripix 300 and Tripix
1200 fixtures that does not exceed 7.2 meters.
Details of standard US and EU conductor identification systems are
given in Table 1.
Wire color
(US system)
Wire color
(EU system) Conductor Symbol Screw (US)
black brown live L yellow or
brass
white blue neutral N silver
green yellow/green ground
(earth) green
Table 1: Conductor identification
Important! Check that all installation work is completed and carry
out appropriate tests and safety checks before applying power.
Power plug
If you decide to fit the supplied power cable tail with a plug that is
suitable for your AC mains power outlets, install a grounding-type
(earthed) plug following the plug manufacturer’s instructions.
Table 1 shows some possible pin identification schemes; if pins are not
clearly identified, or if you have any doubts about proper installation,
consult a qualified electrician.

17 Tripix user manual
Installation setup
Important! Read this description carefully before applying power.
Incorrect configuration of the Tripix system may permanently
damage the Tripix fixture.
The distance between fixtures can be extended by using the Tripix
Cable Adapter, IP66, Male+Female only (P/N 91611323).
A Tripix DMX Input Adapter (P/N 91611337) is necessary for external
DMX control and fixture configuration via MUM. It is not supplied as
standard and needs to be ordered separately.
The Tripix system consists of:
•The Tripix Power, a power supply that provides fixtures with power
at 48 V DC.
•A Power Inserter 3-way cable (see Figure 7), P/N 91611339, that
is used to connect a Tripix Power device and a DMX signal to
Tripix fixtures.
Power
In
Out
Figure 7: Tripix Power Inserter Cable

18 Tripix user manual
Connection to power, fixtures and DMX is indicated on the Power
Inserter (see Figure 8). The DMX signal runs from “In” to “Out”; The
Tripix Power is connected to the plug marked “Power”, and Tripix
fixtures are connected to the end marked “Out”.
Power
In
Out
Figure 8: Connection instructions on Power Inserter
•A DMX Input cable, P/N 91611337, that must be connected to the
Power Inserter cable for connection to a 3-pin XLR DMX output if
DMX control is required. This adapter cable must be ordered
separately.
Install the system following the rules below:
1. One Tripix Power must be connected to the maximum permitted
number of fixtures as one group. The DMX signal can be
connected between groups as shown in Figure 9.
Out In
Power DMX
Out In
Power
Figure 9: Connection of groups
DMX termination plug
DMX

19 Tripix user manual
2. See Figure 10. When all groups of fixtures are connected correctly,
connect a Martin cable-mounted 13-pin DIN male DMX
Termination Plug (P/N 91611336) in the DMX output of the last
fixture of each separate chain of fixtures.
Figure 10: DMX termination plug
3. For DMX control and remote configuration via MUM, connect a
DMX Input Adapter to the Power Inserter.
4. Use a three-wire power cable, cable diameter based on the lengths
below.
Total Length Cable specification
1 - 15 m
(3.3 - 49 ft.) IP66 extension cable or
16 AWG or 1.5mm2
15 - 40 m
(49 - 131 ft.) 14 AWG or 1.5mm2
40 - 80 m
(131 – 262 ft.) 12 AWG or 2.5mm2
5. Use CAT5 or better data cable.
6. See Figures 11 and 12. If you need to extend the distance
between fixtures, use a set of Tripix Cable Adapters, IP66,
Male+Female (P/N 91611323).
7. When installing fixtures outdoors or in a wet or damp environment,
install each cable adapter inside an IP66-rated electrical junction
box (not provided). Ensure that all cable grommets are completely
sealed against moisture and dust. Failure to seal the box can lead
to damage and risk of electric shock! Use only cable and junction
boxes that are approved for installation and conform to all local

20 Tripix user manual
and national building codes.
Figure 11: Cable Adapter IP66 Male+Female
Figure 12: CAT5 cable and power cable connections