MaskForce MFP01 User manual

Document P/N: 40504-WI-001
REV: A00 CN: 1st Issue
Page: 1of 2
MaskForce Face Mask
Model: MFP01 & MFP02
Manufactured in the U.S.A.
Instructions for Use
INTENDED USE / DISCLAIMERS:
The MaskForce Face Mask is a general use face mask.
MATERIAL COMPONENTS:
The MaskForce Face Mask does not contain any latex or fiberglass. The following is a list of potential body
contacting materials:
Number
Component
Material
FDA Number
[1]
Strap
Medical Grade Silicone
FDA 21 CFR 177.2600
[2]
Seal
Medical Grade Silicone
FDA 21 CFR 177.2600
[3]
Shell
Medical Grade Polypropylene
FDA 21 CFR 177.1520
[4]
Filter Element
H&V Technostat
[5]
Cap-Lock
Medical Grade Polypropylene
FDA 21 CFR 177.1520
WARNINGS:
Do not use the MaskForce Face Mask in the presence of a high intensity heat source or flammable gas.
The MaskForce Face Mask does not eliminate the risk of contracting any disease or infection. Change
immediately if contaminated with blood or bodily fluid.
STORAGE METHOD:
Store in cool, dry place 40-100º F
CLEANING INSTRUCTIONS:
1. Fully disassemble the MaskForce Face Mask including the seal, strap, filter element, and Cap-lock.
2. Clean the MaskForce Face Mask using a soft bristle brush to adequately remove adhering substances
from each component while soaking in a commercially available anionic detergent. Extra attention should
be given to the crevices and cavities during cleaning.
3. Rinse the MaskForce Face Mask with at least 5 liters of water and air dry out of direct sunlight.
DISINFECTING INSTRUCTIONS:
The filter materials cannot be disinfected using the methods listed.
Replace filter after each use.
Ensure all parts are removed prior to disinfecting the MaskForce Face Mask.
Wipe down all surfaces using Cidex wipes making sure to pay extra attention to the crevices and cavities.
AFTER DISINFECTION:
Inspect all parts for damage or wear; replace any parts that have visibly deteriorated (cracking, crazing,
tears, etc.)
Rinse thoroughly with water and air dry out of direct sunlight. Make sure the MaskForce Face Mask is
dry before use. – follow assembly instructions to reassemble the MaskForce Face Mask

Document P/N: 40504-WI-001
REV: A00 CN: 1st Issue
Page: 2of 2
ASSEMBLY INSTRUCTIONS:
1
Place seal on Mask.
Start at the nose, snap
the seal onto the shell,
press the seal onto the
mask working your way
around the shell
perimeter, check secure.
2
Thread the strap.
With shell nose
down, thread the
strap downwards
through the top hole
[T] & up through the
chin hole [C], repeat
on the other side
3a
Thread clip onto strap.
Thread approx. 4cm/1¾”
of strap into the clip
center hole, twist strap
90° and slide through
the notch, repeat on
other side
3b
Twist strap 90° and
slide through the
notch, repeat on
other side
4
Install filter element.
Place the filter into the
mask, ensure it is
concentric and flat
5
Install Cap-lock.
Align slots in lock
piece with the shell
notches, gently
press on the
outermost portion of
the Cap-lock and
rotate counter
clockwise until the
tabs lock in place
6
Final check.
Look inside face mask
and ensure the filter
element is even and
there are no gaps
around the edge
QUESTIONS REGARDING USE OR LIMITATIONS:
Please contact MaskForce LLC, Waukesha, Wisconsin, 53188, USA, at [phone], by E-mail:
maskfor[email protected] or refer to our website at www.maskforce1.com