Master Pumps MPG7HP24 User manual

MPG7HP24
GB ENGINE DRIVEN PUMP
TRANSLATION OF THE ORIGINAL INSTRUCTIONS

GB ENGINE DRIVEN PUMP
Dear customer,
Congratulation for buying your new device from MASTER PUMPS
Like all our products, this one, too, was developed using the latest technological knowledge The device
was manufactured and assembled on the basis of state-of-the-art pump technology using most reliable
electrical or electronic components which ensure a high level of quality and a long life of your new
product
Please read through these operating instructions carefully to make sure that you can fully benefit from
all features
Some explanatory illustrations can be found at the end of these operating instructions
We hope you will enjoy your new device!
GENERAL SAFETY INFORMATION
Please read through these operating instructions carefully and make yourself conversant with the
control elements and the proper use of this product We shall not be liable in the case of damage
caused as a result of the nonobservance of instructions and provisions of the present operating
instructions Any damage caused as a result of the nonobservance of the instructions and
regulations contained in the present operating instructions shall not be covered by the warranty
terms Please keep these operating instructions in a safe place and hand them on together with
the device should you ever dispose of it
Children and other persons not conversant with the contents of these operating instructions must
not use this device Please keep an eye on children to make sure they will not use the unit as a toy
to play with In various countries, applicable provisions may be in place which might contain
restrictions regarding the age of the user, and they have to be adhered to in any case
The device must not be operated by people with restricted physical, sensory or mental capabilities
unless they are either under the supervision of a person being responsible for their safety, or
receiving from such a person instructions as how to use the device, respectively

1.1. Safety of work place
1. Keep your work place tidy and well lighted. Disorder or poorly lighted work places can cause
accidents.
2. Do not work with a motor driven device in an environment of flammable gas, vapor or liquids.
Motor driven devices generate sparks, which can ignite combustible dust or vapor.
3. Keep children and other persons out of reach when using this device. If distracted you might
lose the control over the device.
1.2. Safety of persons
1. Be careful, watch out what you are doing and work reasonable with a motor driven device.
Do not use a motor driven device, if you are tired, under impact of drugs, alcohol or medication. A
moment of carelessness could cause serious injuries.
2. Avoid any accidental operation. Make sure, the motor driven device is switched off, before
you pick it up or carry it.
1.3. Safety when using a combustion engine
1. Do NEVER operate an engine inside a building or in closed areas, except you make sure the
exhausting gas is transported outside completely. The motor exhausting gas contains
carbonmonoyde, which cause unconsciousness or even death.
2. Do not smoke or work near the machine.
3. Check regularly all fuel lines and tank for any leaks and cracks.
4. Switch of the engine, if the machine gets filled with fuel.
5. Do not refuel, if the machine is running or hot.
6. Do not refuel near of sparks, open fire or a smoking person.
7. Never refuel a gasoline or Diesel engine inside a room without sufficient air ventilation.
8. Do not overfill the tank and avoid to spill gasoline when refueling. Spilled gasoline or vapors
can get ignited. In case gasoline was spilled out, please make sure everything is dry before
starting the engine.
9. Make sure, the tank lid is closed correctly and tightly.
10. Under certain conditions, gasoline is easily combustible and extremely explosive.
11. Keep gasoline only in designated containers.
1.4. Maintenance safety
Regular maintenance and care reduce the danger of possible operational disruptions and increase
the life cycle of your device.
1. Make sure, the repair of the motor and machine is done by qualified personal.
2. Make sure, the motor is switched OFF and the ignition got interrupted, before the protective
devices are dismounted or removed.
3. Keep the engine clean and make sure all stickers are legible. On the stickers are important
operational instructions and warnings. Replace missing or illegible stickers.

4 Do not use any gasoline or flammable solvents for cleaning the machine Vapors and
solvents can get exploded Store the machine properly at a clean, dry place, and keep out of reach
for children
Notes and inst uctions with the following symbol equi e pa ticula attention:
Any non observance of these instructions
involves the danger of bodily harm to people
and/or damage to property
Please inspect the device for damage occurred during transportation In case of damage, the
retailer has to be informed immediately, at the latest within 8 days after the date of purchase
SYMBOLES
Compliance with
appropriate
safety standards
Read the instruction
manual before starting
the engine and using
your equipment
WARNING
High temperature
exhaust gas, do not
touch
CHOKE
Start/stop valve
(ON/OFF) Pull to
engage and allow the
engine to be started
when it is cold When
the engine has started,
push the valve to
disengage it
Maximum declared
acoustic power level
WARNING Fill
only with petrol
Never fill the tank with
diesel
Allow the engine to
cool before opening the
petrol tank The
petrol vapours are
very inflammable and
can burst into flame on
simply contacting the
hot surfaces of the
equipment

WARNING
Fill the
engine sump with
an approved oil
(SAE15W-40)
Check the oil
level regularly and
fill up to the
maximum level
mark
Toxic fumes; Don’t
operate inside house
Fuel is flammable, keep
fire away Do not add
fuel with running
machine
When repairing, please
picks up the spark plug,
then repairs it according
to the operational
manual
The engine warm
during use Be careful
when using the device
no smoking
No fires
2. RANGE OF USE
Petrol engine pumps from MASTER PUMPS are portable, self-priming pumps operated with petrol
or a petrol-oil mixture, depending on the model These high-quality products with their convincing
performance data were developed especially for mains-independent irrigation or drainage
applications Compact dimensions and a low weight facilitate transportation between changing
locations of use These units are suitable for pumping clean to slightly dirty water
The typical anges of use of pet ol-engine pumps include:
This pump is not suitable for discharging salt
water, faecal waste, inflammable, etching,
explosive or other hazardous liquids Likewise,
it is not to be used for discharging drinking
water and other food

Please observe the max and min
temperatures of the liquids to be discharged
stated in the technical data
3. TECHNICAL DATA
Cylinder capacity 79 6 cm³
Max power 1 4Kw / 3600min
-
1
Power Hp 2 4Hp
Engine 4-stroke engine, air-cooled
Speed 3840 min
-
1
Tank volume 2 0 L
fuel Petrol, unleaded (RON 95 / 98)
Maximum operating time 1 5h
Oil capacity 400 ml
Maximum flow 117 L/min (7m³/h)
Max delivery height (Hmax) 30 m
Max suction height 7 m
Maximum particle size 5 mm
Max fluid temperature (Tmax) 40°C
Min fluid temperature 2°C
Pipe connection 1’’ (25mm)
Spark plug E6RTC
Weight (w/o fuel) 13 Kg
Guaranteed sound power level L
WA
107 dB(A) K = 3 dB(A)

WARNING! When the acoustic pressure exceeds the value of 85 dB(A), it is necessary to
wear personal ear protection equipment.
Weighted root mean square acceleration according to relevant standard : < 2 5 m/s²
4. INSTALLATION
Depending on the unit being used, the petrol engine pumps from MASTER PUMPS are mounted
on a solid base plate with vibration dampeners These components must be in place during the
operation of the unit since they provide for a secure standing and reduce vibrations
4.1. Gene al installation info mation
During the entire installation process, the unit
must not be running
All connection lines have to be perfectly tight since leaking lines may affect the performance of the
pump and cause considerable damage Therefore, please use Teflon tape to seal the contact
surfaces between the threaded sections of the lines and the connection with the pump This use of
sealing material such as Teflon tape is the only way to ensure an airtight assembly
When tightening threaded connections, please do not apply excessive force which may cause
damage When laying the connection pipes, you should make sure that the pump is not exposed
to any form of weight, vibration or tension
4.2. Installation of the intake line
The inlet of the intake line is to be equipped
with a filter for keeping away larger dirt particles
contained in the water which might clog or even
damage the pump
The liquid to be discharged enters the pump through the suction line Please use a suction line
having the same diameter as that of the suction port of the pump If the suction height exceeds 4
m, however, it is recommendable to use a 25% larger diameter - including appropriate reducer
elements for the connectors
The inlet of the intake line is to be equipped with a filter for keeping away larger dirt particles
contained in the water which might clog or even damage the pump
Moreover, it is highly recommended to install a check valve (non-return valve) which prevents the
pressure from escaping after the pump has cut out and thus protects the pump from damage
caused by pressure surges This check valve may be installed either directly at the suction port of
the pump or at the inlet of the intake line The installation at the inlet of the intake line has proven
to be beneficial since it facilitates the venting of this intake line by enabling it to be filled with water

The check valve with the intake filter - i e the entirety of the intake section of the suction port -
must be immersed by at least 0 3 m below the surface of the liquid to be pumped This will prevent
air from being taken in In addition, please ensure a sufficient distance of the suction line from both
the ground and the sides of water courses, rivers, ponds etc in order to prevent stones, plants etc
from being sucked in
4.3 Installation of the p essu e line
The pressure line conveys the liquids to be discharged from the pump to the point of withdrawal
To avoid dynamic flow losses, one should use a pressure line having at least the same diameter as
the pressure port of the pump
4.4 Stationa y installation
For stationary installation, please fasten the pump on a suitable, solid surface
5. PUTTING INTO OPERATION
5.1 Set-up and visual inspection
The exhaust gases of petrol engine pumps
contain toxic, odourless carbon monoxide
which may lead to serious health damage or, in
extreme cases, even to death when inhaled
For the sake of the safety of people and
animals the devices must not be used in poorly
ventilated locations and in no case inside
confined spaces Generally, please avoid any
inhalation of the exhaust gases
Please inspect the petrol engine pump visually
each time prior to using it A damaged unit must
not be used
The petrol engine pump must only be operated
in flood-proof areas
At every start of the pump, please make sure that the pump is set up securely and standing firmly
The unit must always be positioned upright on an even surface The petrol engine pump must only
be operated in flood-proof areas

Please select the operating location of the pump in such a manner that leaking fuel or motor oil
cannot cause any damage When using it for ponds, basins, construction pits, watercourses or in
similar applications, the pump has to be secured against falling in
Please inspect the pump visually prior to each use Make sure all screws are firmly tightened, and
also check the proper condition of all connections A defective unit or a damaged pump must not
be used In any case of damage, the pump has to be inspected by qualified service staff
5.2 Fuel and fuelling
Depending on the model being used, petrol
engine pumps are operated with petrol or a
petrol/oil mixture You should never use any
fuels other than those specified in the technical
details of your product
During fuelling, smoking is not allowed, and
please keep away open flames Do not inhale
the vapours
Fill the fuel tank with fresh fuel Depending on the model being used, petrol engine pumps from
MASTER PUMPS are operated with petrol or a petrol/oil mixture The required type of fuel is
stated in the technical details of the specific model Please do not use fuel grades types other the
one mentioned for your product
Do not fill in fuel while the engine is running Stop the pump prior to each fuelling cycle and allow
at least five minutes for the unit to cool down before you start fuelling During fuelling, the device
has to be standing upright on an even surface in order to avoid spilling or leaking of fuel Fuelling
should only be performed in a sufficiently ventilated environment Prior to starting the engine,
please wipe off any petrol spillage carefully
During fuelling, smoking is not allowed, and please keep away open flames Do not inhale the
vapors
5.3. Moto oil
If you are using a unit with auto-lubrication, please check the
oil level prior to each use
When topping up motor oil, smoking is not allowed, and please
keep away open flames Do not inhale the vapors
When using units with auto-lubrication, please check the oil level prior to each start using the

dipstick provided
During the oil level check, the device has to be positioned level, must not be running and should
have cooled down Please make absolutely sure that the oil level is within the indicated limits of
the minimum and maximum level If required, top up oil through the filling opening into the oil tank
Be sure to use only high-quality fully synthetic 10W-40 grade motor oil Too much oil may be as
harmful as too little - for instance because of the hazard of overheating or the possibility of an oil
leakage If too much oil is in the tank, please reduce the oil quantity down to the proper level
Do not top up motor oil while the engine is running To top up oil, the pump should always be
switched off, then allow five minutes for the unit to cool down When filling in motor oil, the device
has to be positioned upright on an even surface to avoid any spilling or leaking of motor oil Prior to
starting the engine, please wipe off any motor oil spillage carefully
During filling in motor oil, smoking is not allowed, and please keep away open flames
Do not inhale the vapours
In the case of the units operated with a petrol/oil mixture, the motor oil is a part of the mixture
The mixture ratio indicated in the technical details has to be observed carefully
Please do not use any motor oil grade other than the one referred to in the technical details
Low-oil safety featu e
The low-oil safety feature serves to avoid damage to the engine in case there is insufficient engine
oil in the crankcase
Before the engine oil level falls below the safety limit, the low-oil safety feature automatically
switches the engine off (the motor switch remains in the ON position when this happens)
5.4. Filling the pump with wate , venting the system
Prior to putting the pump into operation for the
very first time, the pump housing should be fully
vented - i e filled with water - even in the case
of selfpriming units If this venting is omitted,
the pump will not suck in the liquid to be
discharged It is highly recommendable, yet not
mandatory, to vent the intake line as well, i e to
fill it with water
Please use the filling opening to fill the pump housing with water Check to make sure that no
leakage is present Then close the filling opening airtight It is recommendable - but not
indispensable - to fill the intake line with water, too Petrol engine pumps are self-priming This
means that putting them to operation requires only the pump casing to be filled with water, i e not
necessarily the intake line, too However, in this case the pump will take some more minutes to
suck in the liquid to be discharged The additional filling of the intake line will facilitate and
accelerate the first suction cycle considerably If the intake line is not filled with liquid, it might be
necessary during putting to operation to fill the pump housing more than once This will depend on

the length and diameter of the intake line To permit the air to escape, you should open a shut-off
devices in the pressure line, such as for instance a faucet
5.5. Sta ting the engine
To start the engine, you have to put the ignition breaker to the “ON” position, the choke lever to the
start position, and the throttle control to "full throttle" Subsequently, pull the starter rope several
times strongly until the engine starts As soon as the engine is running, slowly move the choke
lever to the “operating” position Priming will start as soon as the engine has begun to run During
this process, please leave the throttle control in the “full throttle” position As soon as the liquid is
being discharged evenly without any noticeable air admixture, priming is completed and the
system is fully vented The throttle control can now be set according to the specific needs
5.6. Ope ation
The petrol engine pump must not run with the withdrawal point being shut
off
The pump must not be operated permanently in the absence of water This
so-called dry running - i e the operation of the pump without any water
being discharged - may cause considerable damage to the unit
The petrol engine pump including the entire line system have to be
protected from frost and climatic influences
Combustible or easily inflammable or explosive matters and objects are to
be kept out of the area of the pump while in operation
Please do not top up fuel motor oil while the engine is running Stop the
pump for fuelling it
During operation, some parts of the petrol engine pump become extremely
hot, for instance the exhaust pipe and its cover After switching the device
off until its cooling down, to avoid injury by burning, the device must only be
touched at the points provided for this purpose, e g at the control elements
or handles
During the first 20 hours of operation of a new device, the engine must not be operated at its full
capacity During this period of time, operation at two thirds of the possible speed is recommended
During this running-in period, full-throttle operation is admissible only for short periods of time up to
a max of 10 minutes, for instance during the priming operation at the time of putting the units to
operation

The pump must not be operated permanently in the absence of water This so-called dry running -
i e the operation of the pump without any water being discharged - may cause considerable
damage to the unit because the required cooling is missing If necessary, you have to stop the
engine, check the intake line and the connection ports for leakages and refill the pump body and
possibly the intake hose, too, with water
The petrol engine pump must not run with the withdrawal point being shut off Do not let the pump
“work” against a closed pressure side
Please do not top up fuel or motor oil with the engine running For fuelling, please switch the pump
off and allow at least five minutes for it to cool down During fuelling, and also during operation or
as long as the device is switched off, please make sure that it is standing upright on a level surface
in order to prevent any spilling or leaking of fuel
Do not touch the exhaust pipe and its cover during operation since these parts become very hot
and bear the hazard of burning Even after the device has been switched off, these parts remain
very hot and must only be touched after allowing for an appropriate period of four cooling down
Other parts of the engine, too, become hot during operation Therefore, please avoid to touch the
unit during operation and afterwards from power-off to its cooling down at any points other than
those intended for this purpose, e g at the control switches and levers or the handles
Combustible or easily inflammable or explosive matters and objects are to be kept out of the area
of the pump while in operation Please do not place any objects on top of the engine
5.7. To stop the engine
Put the throttle control to the idle position, then the ignition breaker to “OFF”
The pump inlet is equipped with a valve which will prevent the water from escaping out of the
pump housing after the pump was switched off This return stop will shorten the required priming
period at the next start Moreover, in this way it is not necessary to fill the pump housing with water
at the next start of the pump
5.8. Ending the application
The pump must not be transported with its fuel tank filled
After each use, please drain the water contained in the pump through the opening provided for this
purpose Allow the pump body to dry well to avoid possible damage by corrosion In the case of
frost, water remaining inside the pump may freeze up and thus cause considerable damage
If the device is transported after having been in use, the fuel has to be drained completely
Transporting the pump with its fuel tank filled is not allowed

6. MAINTENANCE AND TROUBLESHOOTING
If possible, please stop the engine, pull off the spark plug socket, and allow
the engine to cool down prior to performing any maintenance work If it is
necessary to keep the motor running for performing certain maintenance
work, please ensure sufficient ventilation because the exhaust gases are
toxic
Regular maintenance and thorough care will reduce the risk of possible operational malfunction
and contribute to extend the life cycle of the unit The technical design of engines is very complex,
and they contain a huge number of moving parts which are subject to high mechanical, thermal
and chemical influences from the side of the environment and the combustion process The use of
proper, high-quality and fresh operating fluids - fuel and motor oil - will prevent both damage to the
engine and downtimes
Abrasive matters contained in the liquid being discharged - such as sand - accelerate wear and
tear and reduce the performance of the pump When discharging liquids containing such matters,
the installation of a prefilter is recommended This useful accessory it will efficiently filter sand and
similar particles out of the liquids, thus minimize wear and tear and extend the lifetime of the pump
6.1. Oil change and oil level check
When using models with auto-lubrication, please check the oil level prior to
each use
Every 100 operating hours or at least once a year and after the first 20 operating hours an oil
change must be performed On models with auto-lubrication, an oil change should be carried out
at least once per year During this period of time, the quality of the motor oil will clearly drop even if
the device is used only infrequently To carry out such an oil change, please drain the old oil and fill
in new oil through the filling opening into the oil reservoir

Quickly turn the engine several times in the running direction, in order to distribute the oil evenly.
Meticulous maintenance and care should include the check of the oil level prior to each use. To
carry out this check, please use the dipstick provided. During the check the unit has to stand level
and must be switched off and cooled down. Please make absolutely sure that the oil level is within
the indicated minimum and maximum limits. Please observe the local regulations regarding the
disposal of waste oil.
6.2. Automatic activation of the low-oil auto-stop feature
The pump is equipped with a low-oil safety feature. The models with auto-lubrication are equipped
with an autostop feature. This handy feature will automatically cut out the engine in case the motor
oil level drops below the required minimum. In this case starting the motor again is impossible
until a sufficient quantity of motor oil has been topped up. When topping up motor oil, please
observe all information contained in this manual regarding motor oil and oil level check.
6.3. Spark plug
Cleaning the spark plug and, where necessary, an adjustment of the electrode gaps should be
performed at intervals of six months or 100 hours of operation.
maintenance on the spark plug
please pull off the spark plug socket first. Then use a spark plug wrench to remove the spark plug.
For a disturbance-free functioning the spark plug has to be dry and free of combustion residues,
and the electrode gap must be between 0.6-0.7 mm.
If required, please clean the spark plug. We recommend to use a fine-wire brush to remove
combustion residues.
Where needed, correct the electrode gap by carefully bending the electrode. In the case of
excessive deposits or worn electrodes you should insert a new spark plug.
Manually screw in the inspector, clean or, possibly, new spark plug until it comes to a stop. Then
tighten the spark plug carefully using the spark plug wrench. Please do not use excessive force in
order to avoid overtightening and consequently damaging the spark plug. To complete your work,
slip the spark plug connector on the spark plug.

6.4. Ai filte
For reason of the fire or explosion hazard involved, please do never use
petrol or solvents with a low flashpoint to clean the air filter
A dirty air filter means that the airflow into the carburetor is inhibited To avoid operational
malfunction of the carburettor, the air filter has to be checked regularly and cleaned or replaced, if
necessary
Basically, checking the air filter for contamination is recommended prior to each use Cleaning
should be performed at the latest every three months or after 50 hours of operation, respectively If
the device is used in a very dirty or dusty environment, it is advisable to shorten the cleaning
intervals, for instance down to 10 hours A new air filter should be installed every six months or
after 300 hours of operation, respectively
maintenance wo k,
please open the air filter box and take the filter out If necessary, wash out the air filter in a non-
combustible solvent such as a washing-up liquid (dishwashing detergent) For reason of the fire or
explosion hazard involved, please do never use petrol or solvents with a low flashpoint to clean the
air filter After cleaning, please allow the air filter to dry
6.5. Replacing the mechanical shaft seal
The mechanical shaft seal is used to seal the pump body from the motor shaft It counts among
the parts which are subject to natural wear and tear
If the mechanical shaft seal is defective, water will escape between the engine and the pump body
Qualified persons should only carry out replacement of the mechanical shaft seal
6.6. Removing fo eign matte s f om the pump
Coarsely sized particles contained in the liquid being discharged may entail the clogging of the
pump body and pump wheel In this case, it is possible to detach the pump housing in order to free
the pump body and the pump wheel from the solid matter

6.7. T anspo t and sto age
In order to avoid the risk of fire, allow the motor to cool down before
transporting or putting it in storage
During transport, the water pump fuel valve should be set to OFF and the
water pump kept level, in order to avoid the fuel leaking out Spilled petrol
or petrol vapours can ignite
If the unit is not used over some extended period of time, the water in the pump ought to be fully
drained Please allow the pump to dry completely in order to prevent corrosion Likewise, the fuel
tank and the carburetor should be emptied, too On the units with auto-lubrication, the motor oil
should be drained as well Prior to placing the unit in storage, it should be cleaned thoroughly and
afforded some kind of preservation, should this be advisable
Please make sure that the device is stored in a dry and frost-proof place
If the water pump is used to pump slightly dirty water, a residue can be left in the pump Before
storage, take in clean water with the water pump, in order to clean it Otherwise, the pump impeller
may be damaged when it is put in service again To clean the pump, unscrew the drain plug (2)
from the pump and drain the pump thoroughly
6.8. T oubleshooting
We decline any liability for damage caused by inappropriate repair
attempts Any damage caused by inappropriate repair attempts will avoid
all warranty claims
None of the remedial actions listed below must be performed with the
engine running

Malfunction
P
ossible cause
Elimination
1. The pump does not
discharge any liquid at
all or only a small
quantity, engine is
running.
1. Not enough liquid in the pump.
2. Leakage in the intake line.
3. Selected motor performance too
low.
4. Filter at the inlet of the intake line
is clogged.
5. Intake line is clogged.
6. Pump wheel is blocked by foreign
matters.
7. Suction height and/or discharge
height too high.
8. Mechanical shaft seal is defective.
9. Pump wheel is not properly
seated.
10. Pump wheel is damaged.
11. Motor is not running smoothly.
1. Fill pump housing through
filling opening with liquid.
2. Check intake line and its
connections. If required, seal
connection parts of intake line
with Teflon tape. Replace
intake line if it shows damage
which cannot be repaired.
3. Increase motor
performance.
4. Clean filter.
5. Clean intake line.
6. Remove foreign matters.
7. Modify the arrangement so
that the suction height and/or
discharge height do not
exceed the maximum value
any longer.
8. Replace mechanical shaft
seal.
9. Arrange pump wheel
properly.
10. Replace pump wheel.
11. Contact customer service.
2. Vibration or loud
noise during operation.
1. Suction height and/or discharge
height to high.
2. Intake line and/or pump wheel
blocked by foreign matters.
3. Instable installation.
4. Unit is not standing firmly.
5. Pump wheel is damaged.
6. Other technical defect.
1. Modify the arrangement so
that the suction height and/or
discharge height do not
exceed the maximum value
any longer.
2. Remove foreign matter.
3. Stabilise the installation.
4. Arrange unit firmly.
5. Replace pump wheel.
6. Contact customer service..

3. Motor does not start
or stop to run during
operation.
1. Lack of fuel.
2. Absence of ignition spark.
3. Clogged carburettor.
4. Clogged air filter.
5. On a model with auto-lubrication,
the auto-stop feature was activated
because the motor oil level had
dropped below required minimum.
6. Other technical defect.
1. Open fuel cock and/or fill in
fuel.
2. Check ignition switch. If
required, check the spark plug.
3. Clean carburetor.
4. Clean air filter.
5. Top up motor oil.
6. Contact customer service..
7. WARRANTY
The present device was manufactured and inspected according to the latest methods. The seller
warrants for faultless material and workmanship in accordance with the legal regulations of the
country in which the device was purchased. The warranty period begins with the day of the
purchase and is subject to the provisions below:
Within the period of warranty, all defects which are to be attributable to defective materials or
manufacturing will be eliminated free of charge. Any complaints are to be reported immediately
upon their detection.
The warranty claim becomes void in the case of interventions undertaken by the purchaser or by
third parties.
Damage resulting from improper handling or operation, incorrect setting-up or storage,
inappropriate connection or installation or Acts of God or other external influences are excluded
from warranty.
Parts being subject to wear and tear are excluded from warranty.
All parts were manufactured using maximum care and high-quality materials and are designed for
a long lifecycle.
It should be understood, however, that the wear and tear depends on the kind of use, the intensity
of use and the internals of maintenance. Complying with the installation and maintenance
information contained in the present operating instructions will therefore considerably contribute to
a long lifecycle of these wearing parts.
In case of complaints, we reserve the option of repairing or replacing the defective parts or replace
the entire device. Replaced parts will pass into our property.

Claims for liquidated damages are excluded unless they are caused by wilful acts or negligence on
the side of the manufacturer.
The warranty does not provide for any claims beyond those referred to above. The warranty claim
has to be evidenced by the purchaser in the form of the submission of the sales receipt. The
present warranty commitment is valid in the country in which the device was purchased.
Please note:
1. Should your device fail to function properly, please verify first whether an operating error or
another cause is present which cannot be attributed to a defect of the device.
2. In case you have to take or send in your defective device for repair, please be sure to enclose
the following documents:
OSales receipt (sales slip).
OA description of the occurring defect (a description as accurate as possible will expedite the
repair work).
3. In case you have to take or send in your defective device for repair, please remove any
attached parts which do not belong to the original condition of the device. If any attached parts of
this kind should be missing upon the return of the device, we shall not be liable for them.
Work under warranty does not extend the initial duration of the contractual guarantee.
The turbine and the filter, which are wearing parts, are excluded from the guarantee.
During the guarantee period the After-Sales Service, in return for payment, will make the
necessary repairs following incorrect operation.
We expressly inform you that MASTER PUMPS is not responsible for damage caused by its
equipment, in so far as this damage is caused by a non-compliant repair, in so far as, in
exchanging parts, original MASTER PUMPS parts have not been used, or if the repair has not
been done by the MASTER PUMPS After Sales Service or on of the MASTER PUMPS approved
After Sales Service Centres. This also applies for any addition of parts and accessories other than
those recommended by MASTER PUMPS.

8. HOW TO ORDER SPARE PARTS
Afte -sales Se vice and Application Se vice
Our after-sales service responds to your questions concerning maintenance and repair of your
product as well as spare parts Exploded views and information on spare parts can also be found
under:www.eco-epa.com MASTER PUMPS application service team will gladly answer
questions concerning our products and their accessories : sav@eco-repa com
9. OSAL HINT
Dispose of the old device acco ding to the egulations in fo ce in you count y.
Such appliance have to be collected separately and disposed of in an environmental-suitable
manner and fed in an recycling system after the end of their life cycle When disposing of this
product, make sure that the fuel and oil are drained from the engine Should you have any
questions, please contact your local waste disposal management or your city administration
Dispose of the product packaging in an environmentally friendly manner in the provided collection
containers
10. ENTREPOSAGE
_ Carefully clean the whole machine and its accessories
_ Store it out of reach of children, in a safe, stable position stable, in a dry, temperate place, avoid
excessively high or low temperatures
_ Protect from direct solar radiation If possible, keep it in the dark
_ Do not enclose it in plastic bags because damp could form there
11. ENVIRONMENT
The equipment must not be thrown away with normal domestic waste but
must be disposed of according to the rules