Masterplug IPS Instruction Manual

Masterplug Help Line Visit our website at
www.masterplug.com
Stafford Park 1 Telford TF3 3BD ENGLAND
03300 249 279 Luceco PLC
Supplied by
PRODUCT IMAGES LINE DIAGRAMS
IPS
PRODUCT INFORMATION
Part Number
Product Dimensions
Sockets
IPS
Height 61.5mm x Width 72.8mm x Depth 172mm
1x IP rated weatherproof socket
TECHNICAL SPECIFICATIONS
Standard(s)
Maximum Load (Wattage)
IP rating
This product is certied to applicable British safety standards
BS1363-2
13A: 3120 Watts, 240 Volts
IP54
IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN
FEATURES
• Ideal for creating a safe convenient temporary outdoor power supply
• 13A inline socket
• Weatherproof (IP54 rated) socket
OUTDOOR
inline weatherproof socket
SAFETY WARNING
PLEASE READ CAREFULLY AND USE IN ACCORDANCE WITH OUR SAFETY INSTRUCTIONS BELOW
Uncoil the ex fully before use
Position the cable carefully to avoid accidents
Occasionally inspect the ex insulation for damage
Check outlet before use for signs of water ingress
Use insulating tape for repairs to damaged ex
Attempt to repair damaged plugs or trailing outlet: replace them
Allow heavy tools to hang unsupported on the ex or from the outlet
Leave the unit unattended when risk of exposure to moisture
1
SOCKET
72.8
61.5
28
172
IP54
RATED
POWER designed with outdoor activities in mind, this range provides
safe power solutions for garden and light DIY use

Masterplug Help Line Visit our website at
www.masterplug.com
Stafford Park 1 Telford TF3 3BD ENGLAND
03300 249 279 Luceco PLC
Supplied by
WIRING INSTRUCTIONS
If unit was supplied without pre-tted mains cable, or the supplied cable is being replaced,
the correct cable MUST be used.
Use exible cable:
• Ordinary duty, PVC or Rubber construction*
• 300/500V mains, 3-Core 1.25mm or 1.5mm
• Round prole
• To BS EN 50525 or equivalent
* PVC insulated & sheathed, Harmonized Code: H05VV-F3 or Rubber insulated &
sheathed, Harmonized Code: H05RR-F3.
1. Turn unit upside down & undo the 4 xing screws on underside securing Base Cover.
Remove Base Cover & Cable Grommet. Ensure Main Body Seal remains in place on Main
Body Assembly.
2. Strip 65-70mm of outer jacket sheath from one end of mains cable, to expose Earth,
Live & Neutral insulated wires
3. Feed ends of wires through Cable Grommet by about 100mm.
4. Strip insulation on each conductor wire 5-7mm to expose copper strands, & twist
strands together to form neat ends.
5. Undo the 2 xing screws & remove Cord Grip.
6. Place cable in strain-relief channel & ret Cord Grip - DO NOT OVERTIGHTEN xing
screws. Ensure the Cord Grip clamps onto the cable outer sheath & NOT individual wires.
7. Route & connect wires to terminals as shown in previous diagram, ensuring connections
as follows:-
GREEN/YELLOW Earth wire to Earth Terminal (central)
BROWN wire to Live Terminal (RH side)
BLUE wire to Neutral Terminal (LH side)
Ensure:-
• ONLY bare ends of wires enter terminals & NO loose strands are visible
• All terminals are located correctly in Base Cover.
• All terminal screws are secure - DO NOT OVERTIGHTEN
8. Adjust position of Cable Grommet on Mains Supply Cable to ensure it ts properly into the Cable Seal adjacent to Cord Grip.
9. Re-assemble Base Cover to Main Body Assembly & ensure Main Body Seal is in place & ts properly against Cable Grommet.
Secure the 4 xing screws – DO NOT OVERTIGHTEN.
10. Wiring is now complete & unit is ready to be used.
REMEMBER - The unit will ONLY provide weatherproof protection when the Cover is closed & the Catch is properly closed or locked.
To close or open catch, press the region of the catch as shown below.
11. During life of product, any cleaning should only be carried out with a damp cloth using a mild solution of detergent & warm
water. DO NOT USE solvent based cleaners as these may cause damage. It is recommended to ONLY clean the external
surfaces with Cover closed.
DO NOT get any water on Socket if Cover is open.
12. For convenience in storage or while in use, a keyhole slot is provided on the rear face for hanging unit onto a No.8 screw
mounted to a suitable surface.