Mastervac 054-0238-8 User manual

INSTRUCTION MANUAL
Wet/Dry Vacuum
054-0238-8

Quick Start Guide
If any parts are
missing or damaged,
or if you have any
questions, please call
our toll-free helpline
at 1-800-689-9928.
Read and understand this instruction manual
thoroughly before using the product. It contains
important information for your safety as well as
operating and maintenance advice.
Keep this instruction manual for future use. Should
this product be passed on to a third party, then this
instruction manual must be included.
WET/DRY VACUUM 054-0238-8

TABLE OF CONTENTS
2
SECTION
TECHNICAL SPECIFICATIONS
SAFETY WARNINGS
EXTENSION CORDS
LOCATION OF PARTS
GENERAL ASSEMBLY INSTRUCTIONS
DRY VACUUM OPERATION
WET VACUUM OPERATION
BLOWER OPERATION
MAINTENANCE
CARTRIDGE FILTER
TROUBLESHOOTING
ACCESSORIES
EXPLODED VIEW
PARTS LIST
WARRANTY
3
4–6
7
8
9
10
11
12
13
14
15
16
17
18
19
WET/DRY VACUUM 054-0238-8

3
SPECIFICATIONS
Peak horsepower:
Power:
Air flow:
Tank size:
Tank:
Hose:
Filters:
Power cord:
Weight:
5
120 V, 60 Hz, 10.5 A
120 CFM at end of hose
45 L (12 U.S. gallons / 10 Imperial gallons)
Polypropylene
2 1/2" x 7' (6.4 cm x 2.1 m)
Cartridge filter, Foam filter, Dust bag
12’ (3.7 m)
17lb 7oz (7.9 kg)
WET/DRY VACUUM 054-0238-8
TECHNICAL SPECIFICATIONS

SAFETY WARNINGS
4
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE MANUAL FOR FUTURE REFERENCE.
Read all instructions before using this appliance
Read and understand this instruction manual and all labels on the Wet/Dry Vacuum before using. Safety
is a combination of common sense, staying alert and knowing how this Wet/Dry Vacuum works. Use this
Wet/Dry Vacuum only as described in this manual. To reduce the risk of personal injury or damage to the
Wet/Dry Vacuum, use only recommended accessories.
Understanding Safety Terminology
DANGER: If safety information is not followed, someone will be seriously injured or killed.
WARNING: If safety information is not followed, someone could be seriously injured or
killed.
CAUTION: If safety information is not followed someone may be injured.
WARNING : To reduce the risk of fire, electric shock, or injury:
When using your Wet/Dry Vacuum follow basic safety precautions including the following:
• Do not run the Wet/Dry Vacuum unattended.
• Do not vacuum, or use this Wet/Dry Vacuum near liquids, gases, or explosive vapours like gasoline or
similar fuels, lighter fluid, cleaners, oil based paints, natural gas or hydrogen. Do not vacuum or use
this Wet/Dry Vacuum near explosive dusts like coal dust, magnesium dust, grain dust, or gun powder,
as sparks inside the motor can ignite flammable vapours or dust.
• Do not vacuum burning or smoking items such as cigarettes, matches, or hot ashes.
• Keep the cord away from heated surfaces.
• Do not expose to rain. Store indoors.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not use if the cord, plug or other parts are damaged.
• If your Wet/Dry Vacuum is not working correctly or has missing parts, has been dropped or damaged,
left outdoors or dropped in water, return it to an authorized service centre.
• Do not pull or carry by the cord. Do not use the cord as a handle, close a door on the cord, or pull the
cord around sharp edges or corners.
• Do not run the Wet/Dry Vacuum over the cord.
• Do not handle the plug or the Wet/Dry Vacuum with wet hands.
• To reduce the risk of health hazards from vapours or dusts, do not vacuum toxic materials.
• Do not use or store near hazardous materials.
• Do not use this Wet/Dry Vacuum with a torn filter or without installing the filter except when vacuuming
liquids as described in the operation section of this manual.
WET/DRY VACUUM 054-0238-8

SAFETY WARNINGS
5
WARNING: To reduce the risk of electric shock, do not expose to rain. Store indoors.
WARNING: For your own safety, read and understand this instruction manual. Do not
operate unattended. Do not use this Wet/Dry Vacuum to pick up hot ashes, coals, toxic,
flammable or other hazardous materials. Do not use near explosive liquids or vapours.
CAUTION: Do not vacuum drywall dust or cold fireplace soot or ash with a standard
Wet/Dry filter. This dust is very fine and hence will not be captured by the filter and may
cause damage. Refer to the operation section for proper filter selection.
• Do not use the Wet/Dry Vacuum as a toy. Pay particularly close attention when it is being used by or
near children.
• To reduce the risk of injury from the Wet/Dry Vacuum accidentally starting, unplug the power cord
before changing or cleaning the filter.
• Do not leave the Wet/Dry Vacuum unattended when it is plugged in. Unplug it from the power outlet
when not in use and before servicing. Turn off the Wet/Dry Vacuum before unplugging.
• Do not put any objects into the ventilation openings. Do not vacuum with any ventilation openings
blocked.
• Keep free of dust, lint, hair or any other items that may reduce the air flow.
• Keep hair, loose clothing, fingers, and all body parts away from openings and moving parts.
• To reduce the risk of falling, use extra care when cleaning on stairs.
When using as blower:
• Direct air discharge only at the work area.
• Do not direct air at bystanders.
• Do not use near children.
• Do not use blower for any purpose other than blowing dirt and debris.
• Do not use Wet/Dry Vacuum as a sprayer.
This Wet/Dry Vacuum is double-insulated, eliminating the need for a separate grounding system. Use
only identical replacements parts. Read the servicing instructions before servicing the Wet/Dry Vacuum.
Use this Wet/Dry Vacuum only as described in this manual.
Observe the following warnings that appear on the motor housing of the Wet/Dry Vacuum.
DOUBLE-INSULATED, GROUNDING NOT REQUIRED. WHEN SERVICING USE ONLY IDENTICAL
REPLACEMENT PARTS.
WET/DRY VACUUM 054-0238-8

6
SAFETY WARNINGS
CAUTION: To reduce the risk of injury from moving parts, unplug before servicing.
WARNING: SERVICING OF DOUBLE-INSULATED WET/DRY VACUUM
In a double-insulated Wet/Dry Vacuum, two systems of insulation are provided instead of
grounding. No method of grounding is provided on a double-insulated appliance, nor should
one be added. Servicing a double-insulated Wet/Dry Vacuum requires extreme care and
knowledge of the system, and should be done only by qualified service personnel.
Replacement parts for a double-insulated Wet/Dry Vacuum must be identical to the parts that
are being replaced. This Wet/Dry Vacuum is marked with the words ‘DOUBLE INSULATED’
and the symbol (square within a square) may also be marked on the appliance.
• For household use only.
• To reduce the risk of electric shock, unplug before cleaning or servicing.
• DO NOT use without filters in place.
• To reduce the risk of electric shock, use indoors only.
POLARIZED PLUG
To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the
other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.
Do not change the plug in any way. Double-insulation eliminates the need for the three-wire,
grounded power cord and grounded power supply system.
WET/DRY VACUUM 054-0238-8

EXTENSION CORDS
7
When using an extension cord with your Wet/Dry Vac refer to the following table to determine the
required AWG wire size. Before using the cleaner make sure the power cord and extension cord are in
good working conditions. Make repairs or replacements before using the vacuum cleaner. Only use
extension cords that are rated for outdoor use.
WET/DRY VACUUM 054-0238-8
Length of Extension Cord
110 V-120 V
Amps
0-6
7-10
11-12
13-16
25’ (7.5 m)
18
18
16
14
50’ (15.25 m)
16
16
16
12
100’ (30.5 m)
16
14
14
150’ (45.7 m)
14
12
12
Not recommended
AWG Wire Size

LOCATION OF PARTS
8
Item Description
1. Handle
2. Top section
3. Blower connection
4. Filter basket
5. 2 1/2" diameter hose (7')
6. Extension wand (x 2)
7. Crevice tool
8. Utility nozzle
9. Floor brush/squeegee
10. Switch
11. Vacuum hose connector
12. Safety float valve
13. Casters (x 4)
14. Foam Sleeve / Wet Filter
15. Drain outlet
16. Household Collector Bag
17. Regular Cartridge Filter
18. Filter retainer
19. Clasp (x 2)
20. Tank
21. Noise diffuser
WET/DRY VACUUM 054-0238-8
5
6
7
13
14
9
8
1
2
3
412
17 18
21
16
10
11
15
19
20

GENERAL ASSEMBLY INSTRUCTIONS
9
2
2
1
5
11
4
9
12
7
10
6
3
8
1. Ensure that the power cord is disconnected from the power outlet (figure 1).
2. Undo the clasps (figure 2).
3. Lift the top section off the tank (figure 3).
4. Remove the contents from inside the tank (figure 4).
5. Turn the tank upside down and insert the casters on the four feet of the tank and secure with the
supplied screws. Ensure that they are mounted correctly. Do not over tighten (figure 5).
6. Insert the handle into the slots on the power head and pressure into place (figure 6).
7. For dry vacuum cleaning, install the supplied cartridge filter and dust bag (figure 7).
8. For wet vacuum cleaning, install the supplied foam filter (figure 8).
9. Replace the top section on the tank (figure 9).
10. Align the top section with the clasps, and snap into place by applying pressure until the clasps click
(figure 10).
11. Insert the large end of the hose into the front inlet of the tank and turn to lock (figure 11).
12. Fit the required accessory on to the suction tube (figure 12).
WET/DRY VACUUM 054-0238-8

DRY VACUUM OPERATION
10
WARNING!
Ensure that you read, understand, and apply the safety instructions in Section 1.
Reminder: DO NOT vacuum hazardous substances. The use of an incorrect filter will
invalidate the warranty.
3
5
8
76
1
4
OPERATING INSTRUCTIONS – DRY VACUUMING
BEFORE STARTING
1. Verify that the power cord is disconnected from the outlet (figure 1).
2. Ensure that the cartridge filter is completely mounted. Ensure that the filter is inserted all the way
(figure 2, figure 3).
3. Verify that the dust bag is installed to the inside of the tank (figure 4).
4. Replace the top section on the tank, and secure it in place using the clasps (figure 5).
5. Insert the larger end of the hose into the front inlet on the tank and lock it in place. Push the required
attachment onto the free end of the hose or extension (figure 6).
6. Plug the power cord into the power outlet (figure 7).
7. Turn the motor on by flipping the switch to the “I” position (figure 8).
8. Once you have completed vacuuming, flip the switch to the “O” position and unplug the power cord
from the power outlet.
DO NOT use the cartridge filter for wet or sharp materials.
DO NOT USE DUST BAG FOR LIQUID VACUUMING.
O = OFF I = ON
WET/DRY VACUUM 054-0238-8

WET VACUUM OPERATION
11
WARNING!
Ensure that you read, understand, and apply the safety instructions in section 1.
Reminder: DO NOT vacuum hazardous substances.
OPERATING INSTRUCTIONS – WET VACUUMING
BEFORE STARTING
8
1
45
6
7
1. Ensure that the power cord is disconnected from the power outlet. Ensure that the tank is clean and
free of dust and dirt (figure 1).
2. Remove the cartridge filter and dust bag. Install a foam filter over the filter basket and place the top
section back on the tank (figure 2). DO NOT use the cartridge filter for wet materials.
3. Fit the desired nozzle to the vacuum hose (figure 3).
4. Ensure that the switch is in the “O” position before plugging the power cord into the power outlet
(figure 4).
5. Turn the motor on by flipping the switch to the “I” position (figure 5).
6. After use, flip the switch to the “O” position and unplug the power cord, then empty and dry the tank
(figure 6, figure 7, figure 8).
Remember! The foam filter must be removed after wet vacuuming and a cartridge filter must be
installed before dry vacuuming again.
IMPORTANT! When vacuuming large quantities of liquids, do not immerse the nozzle completely in the
liquid; leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float
valve that stops the suction action when the container reaches its maximum capacity. You will notice an
increase in motor speed. When this happens, turn off the machine, disconnect from power supply, and
drain the liquid into a suitable receptacle or drain. To continue vacuuming, refit the container with the
drain cap. After wet vacuuming, turn the machine off and remove plug from power supply. Empty the
container, clean and dry the inside and outside before storage.
WET/DRY VACUUM 054-0238-8

BLOWER OPERATION
12
WARNING: Always wear safety goggles complying with ansi Z87.1
(OR in Canada, CSA Z94.3) before using blower.
WARNING: Keep bystanders clear from blowing debris.
WARNING: wear a dust mask if blowing creates dust that might be inhaled.
WARNING: If after a few seconds the hose continues to be blocked, turn off the unit
and clear the hose manually.
2
1
34
5
This Wet/Dry Vac has blowing capabilities. To use the blower feature, follow the instructions below.
1. Insert the large end of the hose into the blower connection in the top of the motor housing (figure 1).
2. Fit the desired nozzle to the vacuum hose (figure 2).
3. Ensure the power switch is turned off and plug in the power supply (figure 3).
4. Turn the motor on by flipping the switch to the “I” position (figure 4).
5. The unit will now blow through the vacuum hose and can be used to clear obstructions within the
hose (figure 5).
WET/DRY VACUUM 054-0238-8

MAINTENANCE
13
6
5
4
2
3
1
1. Ensure that the power cord is disconnected from the outlet (figure 1).
2. Disconnect the hose from the tank (figure 2).
3. Undo the clasps and remove the top section from the tank (figure 3).
4. Clear all dirt or debris from the tank and hose (figure 4).
5. Clean the foam filter by washing it with a mild soapy solution (figure 5).
6. Check the hose, attachments and the power cord to ensure that they have not been damaged
(figure 6).
IMPORTANT! CLEAN THE CARTRIDGE FILTER REGULARLY. IF THE MACHINE IS USED WITHOUT THE
CARTRIDGE FILTER, THE MOTOR WILL BURN OUT AND THE WARRANTY WILL BE VOIDED. ALWAYS
ENSURE TO KEEP SPARE FILTERS HANDY.
REPLACEMENT FILTERS
Replace the filters regularly.
Foam Sleeve / Wet Filter (054-0035) (part # 23)
Dry Reusable filter (054-0148)
Household Collector Bag (054-0003) (part # 31)
Fine Dust High Eff. Collector Bag (054-0214)
Regular Wet/Dry Cartridge Filter (054-0008) (part # 27)
HEPA Wet/Dry Cartridge Filter (054-0159)
WET/DRY VACUUM 054-0238-8

CARTRIDGE FILTER
14
WARNING!
Always disconnect the plug from the wall power outlet before removing the tank cover.
MAINTENANCE
NOTICE! This filter is made of high quality paper designed to stop small particles of dust. The filter
should be used for dry pick-up. It is necessary to use a dry filter to pick up dust as a wet filter will clog
quickly and will be very difficult to clean. Handle the filter with care when removing it for cleaning or
during installation. Check the filter for tears or small holes as even a small hole can allow dust to pass
through and out of the vacuum. Do not use a filter with holes or tears; replace it immediately.
INSTALLATION AND CLEANING
1. Slide cartridge filter down over filter cage (figures 1 & 2).
2. Place retainer on top of cartridge filter against hole of basket (figure 3).
3. Hold lid assembly and turn retainer clockwise until tight. Ensure that there is no gap between filter and
lid assembly (figure 4).
4. To remove filter for cleaning again, hold lid assembly with one hand and turn retainer
counter-clockwise (figure 5).
5. Slide cartridge filter off filter cage (figure 6).
6. Clean filter by tapping it on the inside of trash can (figure 7).
7. Clean filter by rinsing from the inside (figure 7).
8. When wet (to prevent mold and/or mildew build-up), the cartridge filter should be moved and allowed
to air dry for a 24-hour period before being re-installed back onto the filter cage.
WET/DRY VACUUM 054-0238-8

TROUBLESHOOTING
15
WET/DRY VACUUM 054-0238-8
Symptom
Wet/Dry vacuum will not
operate.
Motor cover emits dust.
Reduced efficiency and
motor/speed vibration.
Possible Causes
No power supply.
Faulty power cord.
The tank is full of liquid.
The cartridge filter is
missing or damaged.
Filter may be blocked
by fine dust.
Corrective Action
Check power supply: cord,
breakers, fuses.
Check the power cord and repair
or replace it as necessary.
Empty the tank.
Attach or replace the cartridge
filter.
Check the nozzle, the hose and
the tank or filter inlet for
blockage.
Remove the filter, wash and clean
it. Do not reuse until it is
completely dry. Use a new filter if
necessary.
Blockage in the nozzle,
hose or the tank inlet.

ACCESSORIES
16
Consumables
054-0035 Foam Sleeve / Wet Filter
054-0148 Dry Reusable filter
054-0003 Household Collector Bag
054-0214 Fine Dust High Efficiency Collector Bag
054-0008 Regular wet/dry Cartridge Filter
054-0159 HEPA wet/dry Cartridge Filter
2 1/2" Accessories
054-0036 Hose
054-0046 Bulk kit
054-0004 Crevice tool
054-0013 Round brush
054-0033 Car nozzle
054-0039 Extension wand
054-0049 Utility nozzle
054-0057 Hose connector
054-0058 Floor brush/squeegee
054-0082 Hose grip
054-0141 Concentrator nozzle
054-0079 Claw utility nozzle
054-0080 2-1/2˝ to 1-1/4˝ conversion unit
054-0215 Universal tool adapter
054-0226 Drain Hero
WET/DRY VACUUM 054-0238-8
Additional accessories for your MasterVac®Wet/Dry Vacuum are available.

EXPLODED VIEW
17
WET/DRY VACUUM 054-0238-8

PARTS LIST
18
WET/DRY VACUUM 054-0238-8
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Description
Handle
Head assembly
45 L (12 U.S. gallon / 10 Imperial gallon) tank
Hose inlet assembly
Drain outlet
Casters x 4
Foam Sleeve / Wet Filter
Crevice tool
Hose
Extension wands x 2
Cartridge Filter
Household Collector Bag
Floor brush/squeegee
Utility nozzle
Noise diffuser
If any parts are missing or damaged, or if you have any questions,
please call the Toll-free Helpline, at 1-800-689-9928.

WARRANTY
19
MASTERVAC™LIMITED WARRANTY
This MASTERVAC®product is guaranteed for a period of three (3) years from the date of original
retail purchase against defects in materials and workmanship.
Subject to the conditions and limitations described below, this product, if returned to us with proof of
purchase within the stated warranty period and if covered under this warranty, will be repaired or
replaced (with the same model, or one of equal value or specification), at our option. We will bear the
cost of any repair or replacement and any costs of labour relating thereto.
This warranty is subject to the following conditions and limitations:
a)
b)
c)
d)
e)
f)
g)
h)
i)
Additional Limitations
This warranty applies only to the original purchaser and may not be transferred. Neither the retailer nor
the manufacturer shall be liable for any other expense, loss or damage, including, without limitation, any
indirect, incidental, consequential or exemplary damages arising in connection with the sale, use or
inability to use this product.
Notice to Consumer
This warranty gives you specific legal rights, and you may have other rights, which may vary from
province to province. The provisions contained in this warranty are not intended to limit, modify, take
away from, disclaim or exclude any statutory warranties set forth in any applicable provincial or federal
legislation.
Imported by Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8
a bill of sale verifying the purchase and purchase date must be provided;
this warranty will not apply to any product or part thereof which is worn or broken or which has
become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation,
operation or maintenance (as outlined in the applicable owner’s manual or operating instructions) or
which is being used for industrial, professional, commercial or rental purposes;
this warranty will not apply to normal wear and tear or to expendable parts or accessories that may be
supplied with the product which are expected to become inoperative or unusable after a reasonable
period of use;
this warranty will not apply to routine maintenance and consumable items such as, but not limited to,
fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or adjustments;
this warranty will not apply where damage is caused by repairs made or attempted by others (i.e.
persons not authorized by the manufacturer);
this warranty will not apply to any product that was sold to the original purchaser as a reconditioned or
refurbished product (unless otherwise specified in writing);
this warranty will not apply to any product or part thereof if any part from another manufacturer is
installed therein or any repairs or alterations have been made or attempted by unauthorized persons;
this warranty will not apply to normal deterioration of the exterior finish, such as, but not limited to,
scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical
cleaners; and
this warranty will not apply to component parts sold by and identified as the product of another
company, which shall be covered under the product manufacturer’s warranty, if any.
WET/DRY VACUUM 054-0238-8