Matrix IC3 User manual

CAUTION !
Read all precautions and instructions in this manual before using this equipment. Keep this manual
for future reference.
Improper assembly, maintenance or use can void the warranty terms.
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 1
Matrix IC3
model no.:
IC-MXIC3B-01
Manufactured by:
Indoorcycling Group GmbH
Happurger Str. 86
90482 Nuremberg | Germany
www.indoorcycling.com
[email protected]
MATRIX Fitness Systems Corp.
1610 Landmark Drive
Cottage Grove, WI 53527
Toll-free: 866.693.4863
Local: 608.839.8686
ENG ESP

TABLE OF CONTENTS
Important precautions page 3
Before you begin page 4
How to assemble the Matrix IC3 Indoor Cycle page 5-7
How to operate page 12
Initial install checks page 8
How to adjust the Matrix IC3 Indoor Cycle page 9-11
Resistance adjustment page 12
How to move the Matrix IC3 Indoor Cycle page 12
Preventative maintenance page 13
Daily maintenance page 13
Weekly maintenance page 13
Bi-Weekly maintenance page 14-15
Monthly maintenance page 15-16
Maintenance activity plan & check lists page 17-18
Exploded drawings of structural components page 19-23
Spare part reference list page 24-28
Limited warranty page 29
The Matrix IC3 Bike is, according to EN 957, a Class S product for professional
and / or commercial use. Such training equipment is intended for use in training areas
Foot print: 52 x 120 cm / 20.5 x 47.2 inch
Weight of bike: 57kg / 126,66 lbs
Max saddle height: 115 cm / 45.3 in
Max handlebar height: 115 cm / 45.3 in
Max user weight: 130 kg / 287 lbs
The bike is designed to accommodate most users from 150 to 205 cm / 59.1 to 81.7 in
in body height.
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 2

IMPORTANT PRECAUTIONS
WARNING!
To reduce the risk of serious injury, read the following important precautions and information before
operating the Matrix IC3 Indoor Cycle.
It is the responsibility of the owner to ensure that all users of the Matrix IC3 Indoor Cycle are
informed of all warnings and precautions.
Operate and maintain the Matrix IC3 Indoor Cycle only as described in this manual.
Do not operate the Matrix IC3 Indoor Cycle until it is properly assembled (see page 5-7).
Keep the bike indoors, away from moisture and dust. Do not place the Matrix IC3 Indoor Cycle in
a garage or covered patio or near water.
place a mat beneath the Matrix IC3 Indoor Cycle. Make sure that there is adequate room around
the Matrix IC3 Indoor Cycle to mount, dismount, and operate it.
Regularly inspect and properly tighten all parts of the Matrix IC3 Indoor Cycle as recommended
in this manual. Please replace defective parts immediately, and do not use the bike until repair is
performed. Use only original parts from the manufacturer.
Children under the age of 14 should only be allowed use of the Matrix IC3 Indoor Cycle with
parental consent and guidance by a specially trained instructor.
The Matrix IC3 Indoor Cycle should not be used by persons weighing more than 290 pounds
(130 kg).
Always wear appropriate athletic attire and shoes while operating the Matrix IC3 Indoor Cycle. Do
not wear loose clothing that could become caught on the Matrix IC3 Indoor Cycle or shoes with
loose laces.
Before using the Matrix IC3 Indoor Cycle, make sure that you are familiar with the operation of
the Indoor Cycle (see pages 8-12).
If you feel pain or dizziness while exercising, stop immediately, rest and cool down.
If replacement parts are needed, use only manufacturer-supplied parts.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
WARNING
Before beginning any exercise program, consult your physician. This is especially important for
persons over the age of 35 or persons with pre-existing health problems. Read all instructions
prior to use. Be aware that incorrect or extensive training can result in serious health injuries. The
manufacturer assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 3
ENG ESP

BEFORE YOU BEGIN
Dear Customer,
Congratulations on selecting the Matrix IC3 Indoor Cycle.
The Matrix IC3 Indoor Cycle offers an impressive array of features designed to
are beginners or experienced athletes, the Matrix IC3 Indoor Cycle offers workouts that
Indoor Cycle.
If you have questions after reading this manual, please contact Indoorcycling Group GmbH or
visit the website www.indoorcycling.com. Before reading further, please familiarize
yourself with the parts that are labeled in the drawing below.
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 4
Emergency brake handle
Lever handle
Saddle
Adjustment
knob
Combi
pedal
Chain guard
Resistance knob
Handlebar
Adjustment knob
Brake pad
Flywheel
Transport wheel
Leveling feet
frame. Please refer to this number in servicing and maintenance lists.
Lever handle

HOW TO ASSEMBLE Matrix IC3 Indoor Cycle
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 5
SW 17mm
SW 13mm
3mm
5mm hand tight
1x
15mm Pedal
Wrench
1x
ENG ESP
1
3
2
4
STOP mark STOP mark
Seat clamp must be tightened securely from both sides to minimize loosening during use.

Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 6
HOW TO ASSEMBLE Matrix IC3 Indoor Cycle
SW 17mm
SW 13mm hand tight
1x 1x
15mm Pedal
Wrench
7
56
3mm
5mm

Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 7
HOW TO ASSEMBLE Matrix IC3 Indoor Cycle
SW 17mm
SW 13mm
3mm
5mm hand tight
1x 1x
Pedal marked R installed on right crank
(clockwise), Pedal marked L installed on left
crank (counterclockwise).
force to avoid loosening with use of the
indoor cycle.
15mm Pedal
Wrench
ENG ESP
8 9
10
R
L
13 mm
Seat clamp must be tightened securely from both sides to minimize loosening during use.
Please follow
instructions

The cycle tune-up must be performed at initial installation of the indoor cycle for optimal performance and
longevity. Please read and follow all instructions below. If the indoor cycle is not installed and tuned as
described, components may wear excessively and the indoor cycle may become damaged. If you have
questions about the installation, please contact
(for
example, BRUNOX) .
leveling feet underneath the front and/or rear stabilizer until the rocking motion is eliminated.
2. Verify emergency brake function to assure that emergency brake functions correctly.
3. Brake pad calibration: Turn resistance knob counterclockwise as far as possible (minimum bra-
can go.
4. Apply spray lubricant to the brake pad using the lubrication holes on the plastic part or the brake
pad and externally on the felt pad. Make sure brake pad is thoroughly soaked from end to end
spray lubricant purchased by the gallon (3.7 L) at the local hardware store.
5. Apply Lithium grease to the threads on the lower end of the brake rod. First, turn the resistance
knob clockwise until it stops. Apply a small amount of white lithium grease to the threads on the
brake rod above the two lock nuts. Then, turn the resistance knob counterclockwise until it stops.
6. Apply Lithium grease on the metal threads of all the adjustment knobs.
7. Check four (4) Allen bolts on RS pulley for tightness. If loose, apply LocTite Threadlocker
Blue-242 and retighten.
8. Verify R and L crank arm Allen bolts for tightness. If loose, apply LocTite Threadlocker Blue-242
and retighten.
9. Wipe down bike frame with rag moistened with solvent-free spray lubricant
10. Some parts of the indoor cycle may become loose during shipment. Check crank arms and check
all exposed screws, bolts and nuts, and make sure that they are properly tightened.
Customer Service
1. Provide basic maintenance instructions for clients and direct them to detailed maintenance
instructions (page 13-18).
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 8
INITIAL INSTALL CHECKS

HOW TO ADJUST THE Matrix IC3 Indoor Cycle
The Matrix IC3 Indoor Cycle can be adjusted for maximum comfort and exercise effec-
tiveness. The instructions below describe one approach to adjusting the Matrix IC3 Indoor
Cycle to ensure optimal user comfort and ideal body positioning.
You may choose to adjust the Matrix IC3 Indoor Cycle differently.
Sit on the saddle and position your feet on the pedals, with the balls of your feet directly
above the spindles of the pedals (see the drawing below). Adjust the pedal straps so the
pedals, the pedals feature toe clips on one surface and SPD cleats on the opposite
surface. If desired, use the SPD cleats with cycling shoes instead of the toe clips.
Sit on the saddle and slowly pedal until the right pedal is in the lowest position. Your knees
should be slightly bent with no dropping of the hips.
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 9
to the vertical aluminum stems.
ENG ESP
Please do not adjust saddle
height beyond the STOP mark
on the stem. Also ensure the
pop pin is fully engaged and
securely tightened (page 5).
Please do not adjust saddle
height beyond the STOP mark
on the stem and ensure the
pop pin is fully engaged and
securely tightened (page 5).

Proper horizontal adjustment of the saddle is very important in avoiding injury to the knees.
Sit on the saddle and move the pedals until the crank arms are in horizontal position.
Using your forward leg as a marker, your kneecap should be directly above the
center of the pedal so that a straight line is created between knee and center of the pedal
dismount the Matrix IC3 Indoor Cycle. Next, loosen the rear lever handle, slide the saddle
forward or backward as required, and then retighten the lever handle.
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 10
HOW TO ADJUST THE Matrix IC3 Indoor Cycle
horizontal adjustment
with lever handle

Begin with the top of the handlebar at relatively the same height as, or just slightly higher than,
the top of the saddle and at a neutral
fore/aft position . If your knees touch the
handlebars, or if you experience back discomfort while pedaling for extended periods of
time, the height of the handlebars can be adjusted. First, dismount the Matrix IC3 Indoor
Cycle.
Next, turn the front adjustment knob counterclockwise, slide the handlebar post up or
down, and retighten the adjustment knob.
Next, the horizontal position of the handlebar should be adjusted. If the handlebar is
too close to the saddle, your breathing may feel restricted. If the handlebar is too far
from the saddle, you may experience back discomfort. To adjust the horizontal position
-
sition by positioning your elbow so that it touches the front tip of the saddle at a 90- degree
mid-point. If it is not as described, loosen the fore/aft lever handle and slide the handlebar
Retighten the lever handle.
The handlebar offers a wide variety of hand positions for personal preferences. Changing
your hand position can change the angle of your back, neck, and arms. To minimize the
stress on your muscles during your workouts, change your hand position frequently.
handlebar
fore/aft
lever handle:
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 11
handlebar
up/down
adjustment knob
HOW TO ADJUST THE Matrix IC3 Indoor Cycle
ENG ESP
A
B

increments by use of the resistance knob. To increase the resistance, turn the resistance
knob clockwise. To decrease the resistance, turn the knob counterclockwise.
connected to the pedal binding while riding.
HOW TO OPERATE THE Matrix IC3 Indoor Cycle
!!
Due to the weight of the Matrix IC3 Indoor Cycle, it is recommended that two people
move it. While one person lifts the back of the Matrix IC3 Indoor Cycle, the second person
wheels. Carefully move the Indoor Cycle to the desired location and then lower it.
If the Matrix IC3 Indoor Cycle rocks on
leveling feet (see diagram) underne-
ath the front or rear stabilizer until the
rocking motion is eliminated. Im
portant: Please do not unscrew
the leveling feet more than ½ inch!
Resistance knob
Red emergency
brake handle
Leveling feet
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 12

PREVENTATIVE MAINTENANCE
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 13
door cycle is not maintained as described, components may wear excessively and
1. Make sure that the Matrix IC3 Indoor Cycle is level. If the Matrix IC3 Indoor Cycle rocks
motion is eliminated (see „How to move the Matrix IC3 Indoor Cycle“ on page 12).
cleaned to maintain a hygienic environment. First, apply a disinfectant spray to the handle-
bars and the saddle. Using a lint-free cloth, dry the handlebars and the saddle. Next, apply a
small amount of disinfectant to a lint-free cloth and clean the adjustment knobs and the lock
handles. Avoid using strong detergents on the Matrix IC3 Indoor Cycle frame.
1. Apply a small amount of the lubrication spray to a lint-free cloth. Thoroughly clean
Matrix IC3 Indoor Cycle.
2. For optimal performance of the resistance
system, and to minimize wear on the brake pad,
the
should be applied to the brake pad using the lubri-
cation holes on the plastic part of the brake pad. If
fuzz or lint appears on the brake pad, the brake pad
has become too dry. Lubricant spray should be ap-
plied more frequently. Make sure brake pad is tho-
roughly soaked from end to end with lubricant spray.
Wipe off any excess.
ENG ESP
2

2. To maintain the easy adjustability of the saddle
post, the saddle post should be cleaned and
lubricated. Turn the rear adjustment knob coun-
terclockwise and slide the saddle post out of the
frame. Apply a small amount of lubricant spray to a
lint-free cloth, and clean the saddle post .
Next, loosen the rear lock handle and slide
the saddle carriage as far back as possible. App-
ly a small amount of lubricant spray to a lint-free
cloth, and clean the top of the saddle slide .
Then slide the saddle carriage as far forward as
possible and clean the top of the saddle slide. Fi-
nally, adjust the saddle to the desired position.
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 14
1. The Matrix IC3 Indoor Cycle should not be used
if the emergency brake system is not working pro-
perly.
While sitting on the saddle and pedaling, test the
brake by pulling upward on the emergency brake
complete stop.
PREVENTATIVE MAINTENANCE
1
2
A
B

3. To maintain the easy adjustability of the hand-
lebar post, the handlebar post should be cleaned
and lubricated. First, turn the front adjustment knob
counterclockwise and slide the handlebar post out
of the frame. Apply a small amount of lubricant
spray to a lint-free cloth, and clean the handlebar
post .
Next, reinsert the handlebar post into the frame
and adjust it to the desired height. Loosen
the front lock handle and slide the handlebar
carriage as far back as possible. Apply a small
amount of lubricant spray to a lint-free cloth, and
clean the surface of the handlebar slide . Then
slide the handlebar carriage as far forward as
possible and clean the top of the handlebar slide.
Finally, adjust the handlebar to the desired position.
1. To maintain the smooth function of the height
adjust ment knobs for the handlebar and saddle, the
metal threads on the adjustment knobs must
be lubricated. Use of white lithium grease is recom-
mended.
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 15
PREVENTATIVE MAINTENANCE
ENG ESP
3
1
A
A
B

Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 16
4. The brake pad will become worn as a result of
repeated use. The Matrix IC3 Indoor Cycle should
not be used if the emergency brake system is not
working properly (see page 14)! Should you feel
-
fore the bike is used again! Please check the setting
of the brake system as follows: First turn the resi-
stance regulator on the brake system as far as it will
go to the left (minimum braking effect). If the setting
possible to cycle with a barely noticeable amount
of resistance. The brake pad can be adjusted using
a 10 mm wrench. Next, check the brake pad for
signs of wear. If the brake pad does show signs of
excessive wear, thoroughly soak the brake pad
with lubricant spray using the 2 lubrication holes
. Wipe off the excess.
3. Some parts of the Matrix IC3 Indoor Cycle may
become loose as a result of repeated use. Check
pedals, toe clips and pedal straps, and make sure
that they are properly tightened. Next, check all ex-
posed screws, bolts, and nuts. Make sure
that they are properly tightened. Finally, check the
saddle to make sure that it is not loose or damaged.
Please use Locktite on loose crank arm and pulley
screws.
2. To maintain the easy adjustability of the
resistance system, the threads on the lower end
of the brake rod should be lubricated. First, turn the
resistance knob clockwise until it stops. Next, look
under the right or left side of the frame and locate
the brake rod, which has two lock nuts on its lower
end. Apply a small amount of synthetic grease
(white lithium grease) to the threads on the brake
rod above the two lock nuts. Turn the
resistance knob counterclockwise until it stops.
PREVENTATIVE MAINTENANCE
2
5
4
B
3

MAINTENANCE ACTIVITY AND REQUIRED SCHEDULE
Activity Rotation Details found on
Examples of maintenance plan charts for in-house service technicians:
Weekly maintenance Checklist
Bike No. Production code Observations Action taken Result Name / date
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 17
Feet leveling, disinfection and cleaning of the bike daily page 13
Servicing brake pads, detailed cleaning of the entire bike weekly page 13
Check emergency brake function bi-weekly page 14+16
Clean and lubricate saddle and handlebar sliders / posts bi-weekly page 14-15
Check adjustment knobs monthly page 15
Check brake pad for signs of wear monthly page 13
Check brake system, lubricate monthly page 16
Check pedals, toe clip and straps for signs of wear monthly page 16
Check to ensure connections and components are secure &
correctly tightened monthly page 16
ENG ESP

Monthly maintenance Checklist
Bike No. Production code Observations Action Taken Result Name / date
Bi-Weekly maintenance Checklist
Bike No. Production code Observations Action Taken Result Name / date
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 18
MAINTENANCE ACTIVITY AND REQUIRED SCHEDULE

SPARE PARTS
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 19
Drive Gear Parts
Brake parts
ENG ESP
130
01
00001
01
130 03 00001
01
130
01
00007
01
130
01
00008
01
130
01
00003
01
130
01
00005
01
130 01 00004
01

Flywheel
Version 1.0 2013 IC-MXIC3B-01 Copyright by Indoorcycling Group GmbH 2013 | www.indoorcycling.com ENG 20
Handlebar
SPARE PARTS
150 01 00010
01
150 03 00016
01
150 01 00033
01
900 06 00002
01
100 01 00005
01
150 01 00031
01
150 01 00032
01
150 01 00009
01
150 03 00048 01
150
03
00048
01