Matrix R30 User manual

R30 U30
R50 U50

2
3 ENGLISH
15 FRANÇAIS
27 ESPAÑOL

3
WARNING!
There are several areas during the assembly process that special attention
must be paid. It is very important to follow the assembly instructions correctly
and to make sure all parts are rmly tightened. If the assembly instructions are
not followed correctly, the equipment could have parts that are not tightened
and will seem loose and may cause irritating noises. To prevent damage to the
equipment, the assembly instructions must be reviewed and corrective actions
should be taken.
TOOLS INCLUDED:
FPhillips Screwdriver
FR30/R50: 6 mm Hex Wrench, 5 mm Hex Wrench, 4 mm Hex Wrench
FU30/U50: 5 mm Hex Wrench, 4 mm Hex Wrench, 2.5 mm Hex Wrench, 8 mm Wrench
R30 / R50 PARTS INCLUDED:
F1 Bike Frame
F1 Console Mast
F1 Handlebars
F1 Top Cap Front Cover
F1 Top Cap Rear Cover
F1 Seat Frame Assembly
F1 Seat Bottom
F1 Water Bottle Holder
F1 Mesh Seatback
F1 Outside Cover (R30 only)
F1 Inside Cover (R30 only)
F1 Power Cord
F1 Hardware Kit
Console sold separately
ASSEMBLY
Before proceeding, nd your equipment’s serial number located on a barcode
sticker and enter it in the space provided below.
SERIAL NUMBER
MODEL NAME
FR30
FR50
FU30
FU50
MATRIX EXERCISE BIKE
* Use the information above when calling for service.
SERIAL NUMBER LOCATION
NEED HELP?
If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information
is located on the information card.
U30 / U50 PARTS INCLUDED:
F1 Bike Frame
F1 Seat
F2 Console Mast
F1 Handlebar
F1 Handlebar Set
F1 Bike Seat Bracket
F1 Water Bottle Holder
F1 Console Back Cover
F1 Power Cord
F1 Hardware Kit
Console sold separately
UNPACKING
Unpack the equipment where you will be
using it. Place the carton on a level at
surface. It is recommended that you place
a protective covering on your oor. Never
open box when it is on its side.
IMPORTANT NOTES
During each assembly step, ensure that ALL nuts and bolts
are in place and partially threaded.
Several parts have been pre-lubricated to aid in assembly
and usage. Please do not wipe this off. If you have diculty,
a light application of lithium grease is recommended.
ENGLISH

4
R30 /R50
PAGE 5
U30 / U50
PAGE 10
ENGLISH

5
CONSOLE MAST HANDLEBARS
CONSOLE
CONSOLE MAST
TOP CAP
POWER CORD SOCKET
FRONT SHROUD
CRANK
RESISTANCE TOGGLES
PULSE GRIP
HANDLEBARS
SEAT BOTTOM
MESH SEAT BACK
WATER BOTTLE HOLDER
SEAT BACK ADJUSTMENT
LEVER (R50 ONLY)
SEAT POSITION ADJUSTMENT LEVER
R50 SHOWN
R30
R50
PEDALS
ENGLISH

6
A Open HARDWARE FOR STEP 1.
B Carefully pull the CABLES (1) through the CONSOLE
MAST (2) using the LEAD WIRE (3) located inside
the CONSOLE MAST (2). Discard the lead wire.
C Attach the CONSOLE MAST (2) to MAIN FRAME
(4) using 4 BOLTS (A) and 4 SPRING WASHERS (B).
Torque settings: 23.1 Nm / 17 lb-ft.
Note: Be careful not to pinch any wires while attaching
the console mast.
2
1
3
4
A
B
1 2
Hardware For Step 1
Description Qty
A Bolt 4
B Spring Washer 4
7
B
C
5
6
2
Hardware For Step 2
Description Qty
C Bolt 2
B Spring Washer 2
R30
R50
R30
R50
A Open HARDWARE FOR STEP 2.
B Slide TOP CAP REAR COVER (5) over
CONSOLE MAST (2) and snap into place.
C Slide TOP CAP FRONT COVER (6) over
CONSOLE MAST (2) and snap into place
D Attach HANDLEBARS (7) to CONSOLE MAST (2)
using 2 BOLTS (C) and 2 SPRING WASHERS (B).
Torque settings: 23.1 Nm / 17 lb-ft.
R50 SHOWN
ENGLISH

7
D
E
8
9
10
3 4
R30
R50
R30
R50
A Open HARDWARE FOR STEP 3
B Attach the SEAT FRAME ASSEMBLY (8) to the SEAT
SLIDE (9) using 4 BOLTS (D) and 4 SPRING WASHERS
(E). Torque settings: 23.1 Nm / 17 lb-ft.
C Connect the CABLES (10).
Note: Be careful not to pinch any wires while attaching the seat frame.
Hardware For Step 3
Description Qty
D Bolt 4
E Spring Washer 4
12
11
8
H
G
F
A Open HARDWARE FOR STEP 4
B Attach the SEAT BOTTOM (11) to the SEAT FRAME
ASSEMBLY (8) using 4 BOLTS (F) and 4 SPRING
WASHERS (G).
C Attach the WATER BOTTLE HOLDER (12) to the
SEAT FRAME ASSEMBLY (8) using 2 SCREWS (H).
Hardware For Step 4
Description Qty
F Bolt 4
G Spring Washer 4
HScrew 2
R50 SHOWN
ENGLISH

8
I
8
14
14
13
8
I
C
15
J
NOTE: This step is for R30 models only.
A Open HARDWARE FOR STEP 5.
B Place the INSIDE COVER (13) over the MESH SEAT BACK
(14) and mount the MESH SEAT BACK (14) to the SEAT
FRAME ASSEMBLY (8) with 4 BOLTS (C) and 4 SPRING
WASHERS (I). Torque settings: 23.1 Nm / 17 lb-ft.
C Attach the OUTSIDE COVER (15) to the SEAT FRAME (8) and
INSIDE COVER (13) with 3 SCREWS (J).
5 5
Hardware For Step 5
Description Qty
C Bolt 4
I Spring Washer 4
JScrew 3
Hardware For Step 5
Description Qty
I Bolt 6
R30 R50
NOTE: This step is for R50 models only.
A Open HARDWARE FOR STEP 5.
B Attach the MESH SEAT BACK (14) to the SEAT
FRAME ASSEMBLY (8) using 6 BOLTS (I). Torque
settings: 9.5 Nm / 7 lb-ft.
ENGLISH

9
6 7
R30
R50
A Open HARDWARE FOR STEP 6.
B Connect the CABLES (1) to the CONSOLE (17) and carefully
tuck the excess cable into the CONSOLE MAST (2).
C Attach the CONSOLE (17) to the CONSOLE
MAST (2) using 4 BOLTS (K).
Note: Be careful not to pinch any wires while attaching the console.
R50 SHOWN
17
1
2
K
R30 / R50 ASSEMBLY COMPLETE!
R30 R50
SEAT ADJUSTMENT
To determine proper seat position, sit on the seat and position the ball
of your foot on the center of the pedal. Your knee should bend slightly
at the furthest pedal position. You should be able to pedal without
locking your knees or shifting your weight from side to side.
NOTE: It is recommended that you do not sit on the seat while adjusting its position.
SEAT POSITION
To adjust, lift up on the adjustment
lever and hold. Then, slide the
seat to a position that puts you
in a comfortable pedaling range
(one that keeps a slight bend in
your knee while your legs are in
the extended position). Release
lever to lock the mechanism.
SEAT BACK ADJUSTMENT (R50)
To adjust the tilt angle of the
seat back, rotate the lever down
(counterclockwise) and lean back
on the mesh seat back until the
desired position is achieved. When
the position is set, rotate the lever
upward (clockwise) until it is snug.
The seat back comes equipped
with a spring return system to
return the seat back to its original
position when the adjustment
lever is released and the user is
not leaning against the seat back.
ENGLISH
Hardware For Step 6
Description Qty
K Bolt 4

10
CONSOLE
PULSE GRIP HANDLEBARS
RESISTANCE TOGGLES
SEAT
SEAT ADJUSTMENT LEVER/KNOB
SHROUD
POWER CORD SOCKET
CONSOLE MASTS
WATER BOTTLE HOLDER
TOP CAP
CRANK
PEDALS
U50 SHOWN
U30
U50
ENGLISH