Matsushita Electric SB-PM21E User manual
ORDERNO. MD0502016C2
Speaker System
SB-PM21E
Colour
(M)... Wood GrainType
SPECIFICATIONS
Specification
Type 2way, 2speaker system
Speaker(s)
Woofer 10 cm conetype
Tweeter 6 cm conetype
Impedance 6
Input power (IEC)
HIGH 40 W(Max)
LOW 40 W(Max)
Sound pressure level 82 dB/W(1.0m)
Frequencyrange 50 Hz - 30 kHz (-16 dB)
55 Hz - 25 kHz (-10 dB)
Dimensions(WxH xD) 140 x225 x218 mm
Mass 1.95 kg
System : SC-PM21EG-S MusicCenter : SA-PM21EG-S
Front Speaker : SB-PM21E-M
Notes :
1. Specificationsare subject tochangewithout notice.
2. Mass and dimensionsare approximate.
3. Thelabels“HIGH” and “LOW” on therear of thespeakers
refer toHigh frequencyand Lowfrequency.
2005 Matsushita ElectricIndustrial Co. Ltd.. All rights reserved.
1
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
Unauthorized copying and distribution isaviolation of law.
1. Connection of the Speaker Cables
-Besure to connect speaker cables before connecting the AC
power supplycord.
-The load impedance of anyspeaker used with thisunitmust be 6 .
-Besure to connect the cablefrom the right speaker to the right
terminal and the cablefrom the left speaker to the left terminal.
1. Stripoff the outer covering, and twist the center conductor. Make
sure the bare ends of the wires are not unravelled. (Iftheyare,
twist them tight again.)
2. Insert the wire to the rear panel of the unitand close the lever.
Notes :
-To prevent damage to circuitry, never short-circuitpositive (+)and
negative (-) speaker wires.
-Besure to connect onlypositive (red) wires to positive (+)
terminalsand negative (black) wires to negative (-) terminals.
Placement of speakers
Speakers are designedidenticallysothat no left orright channel orientation is necessary.
Notes :
-Keep your speakers at least 10 mm awayfrom the system for
proper ventilation.
2
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
-These speakers do not have magneticshielding. Donot place them
near televisions, personal computers or other devices easily
influenced bymagnetism.
-To avoiddamage to the speakers, do not touch the speaker cones
ifyou have taken the nets off.
Connection
Use onlythe suppliedspeakers.
The combination of the mainunit and speakers provide the best sound.
Using otherspeakers candamage the unit and sound qualitywill be negativelyaffected.
Notes on speakeruse.
-You can damage your speakers and shorten theiruseful life ifyou
playsound at high levelsover extended periods.
-Reduce the volume inthe following cases to avoiddamage.
-When playing distorted sound.
-When adjusting the sound quality.
2. Connection of the Speaker Wiring
3
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
3. Cabinet Parts Location
4. Replacement Parts List
Notes :
-Important safetynotice :
When replacing anyof these components, be sure to use only
manufacturer’sspecified parts showninthe parts list.
-[M] markings inthe Remarks columns indicates parts supplied by
PAVCSG.
4
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
Ref. No. PartNo. PartName& Description Remarks
CABINETAND CHASSIS
1RFKHBPM21E-M SPEAKER CAB ASS’Y [M]
1-1 RKA0072-KJ LEG CUSHION [M]
2RYBV0025 NETFRAMEASS’Y [M]
3RMG0520-K CATCHER [M]
4XTW3+12JFJ SCREW [M]
5RGKV0110-S TWEETER ORNAMENT [M]
6RGNV0089-K SPEC LABEL [M]
7RHDX40001-K SCREW [M]
8RGKV0109-S WOOFER ORNAMENT [M]
9RMQV0032F FELT(SHORT) [M]
10 RMQV0032R FELT(LONG) [M]
11 RMQ0621 EVAPACKING (TW) [M]
12 RMQV0047 EVAPACKING (WF) [M]
13 RKBV0025-M FRONTBOARD [M]
CAPACITOR
C1 ECEA1HAY4R7S 4.7uf50V [M]
PACKING MATERIALS
Ref. No. PartNo. PartName& Description Remarks
P1 RPNV0065 POLYFOAM [M]
P2 RPF0271 MIRAMAT [M]
SPEAKERS
SP1 EAS6PH124A TWEETER [M]
SP2 EAS10P606D WOOFER [M]
5. Packaging
5
PDFcreated withpdfFactoryProtrialversion www.pdffactory.com
Table of contents
Other Matsushita Electric Speakers manuals
