MAXDATA PLATINUM 100 I User manual

User’s Manual
MAXDATA PLATINUM 100 I
Rev. 1.1

2 3MAXDATA PLATINUM 100 I M9Contents
2 3MAXDATA PLATINUM 100 I M9Contents

2 3MAXDATA PLATINUM 100 I M9Contents
2 3MAXDATA PLATINUM 100 I M9Contents
Contents
1 Setting up the System 5
Safety Information...................................................................................................................................5
Server Position ...................................................................................................................................5
System Access Warnings ..................................................................................................................6
Connecting the System...........................................................................................................................7
Back Panel Connectors ......................................................................................................................7
Powering up the System.........................................................................................................................8
2 Server Features 9
Connector and Header Locations ..........................................................................................................10
Configuration Jumpers ..........................................................................................................................11
SSI Front Panel Connector ....................................................................................................................11
Hardware Requirements .......................................................................................................................12
Processor .........................................................................................................................................12
Memory............................................................................................................................................12
Supported Memory Modules ...........................................................................................................12
Optional Hardware ................................................................................................................................12
Remote Management Module .........................................................................................................12
3 Hardware Installations and Upgrades 13
Before You Begin ..................................................................................................................................13
Tools and Supplies Needed..............................................................................................................13
Installing or Replacing a Processor........................................................................................................13
Installing a Processor .......................................................................................................................13
Installing the Heat Sink..........................................................................................................................16
Removing a Processor .....................................................................................................................17
Installing a PCI Card ..............................................................................................................................17
Installing and Removing Memory..........................................................................................................18
Installing DIMMs ..............................................................................................................................18
Replacing the Backup Battery ...............................................................................................................19
4 Server Utilities 21
Using the BIOS Setup Utility .................................................................................................................21
Starting Setup...................................................................................................................................21
If You Cannot Access Setup.............................................................................................................21
Setup Menus....................................................................................................................................21
Clearing the CMOS ...............................................................................................................................23
Configuring the System for embedded Serial ATA RAID ......................................................................24
Configuring the BIOS .......................................................................................................................24
Creating Intel®Matrix Storage Technology RAID set.......................................................................24
Creating LSI Technology RAID set ...................................................................................................24
Loading the RAID Drivers (Windows Server 2003) ..........................................................................25
5 Technical Reference 27
Power Supply Specifications .................................................................................................................27
300 W Single Power Supply Input Voltage.......................................................................................27
300 W Single Power Supply Output Voltages..................................................................................27

4 PBMAXDATA PLATINUM 100 I M9Contents
Figures
1. Back Panel Connectors .....................................................................................................................7
2. PLATINUM 100 I Controls.................................................................................................................8
3. Board Connector and Component Locations ..................................................................................10
4. Configuration Jumpers....................................................................................................................11
5. SSI Front Panel Connector ..............................................................................................................11
6. Opening the Processor Socket Lever..............................................................................................13
7. Opening Load Plate.........................................................................................................................14
8. Removing Protective Covering from the Load Plate .......................................................................14
9. Inserting the Processor ...................................................................................................................14
10. Closing Load Plate and Socket Lever..............................................................................................15
11. Installing the Heat Sink....................................................................................................................16
12. Installing DIMMs.............................................................................................................................18
13. Removing the Battery .....................................................................................................................20
Tables
1. NIC LEDs...........................................................................................................................................7
2. Feature Summary..............................................................................................................................9
3. Board Connectors and Components ...............................................................................................10
4. Keyboard Commands......................................................................................................................22
5. 300 W Power Supply Output Rating ...............................................................................................27
6. Product Certification Markings ........................................................................................................29
6 Regulatory and Compliance Information 29
Product Regulatory Compliance ............................................................................................................29
Product Safety Compliance ..............................................................................................................29
Product RoHS Compliance ...............................................................................................................29
Product EMC Compliance ...............................................................................................................29
Product Regulatory Compliance Markings .......................................................................................29
Electromagnetic Compatibility Notices .................................................................................................29
Europe (CE Declaration of Conformity) ............................................................................................29

PB 5MAXDATA PLATINUM 100 I M9Setting up the System
1 Setting up the System
Safety Information
Server Position
Please take note of the following criteria for creating a practical and safe workplace when setting up
your computer:
! CAUTION
The system can be used anywhere the temperature is suitable for people. However, rooms with
humidity over 70%, and dusty or dirty areas are not appropriate. In addition, do not expose the server
to any temperatures over +30°C or under +10°C.
! CAUTION
For proper cooling and airflow, operate the system only with the chassis covers installed.
! CAUTION
Make sure that the cables connecting the server to peripheral devices are not tight.
! CAUTION
Make sure that all power and connection cables are positioned so that they are not trip hazards.
! CAUTION
When you save data to your server‘s hard disks or to a floppy disk, they are stored as magnetic
information on the media. Make sure that they are not damaged by magnetic or electromagnetic
fields.
! CAUTION
Because the electronics in your computer can be damaged by jarring, no mechanical devices should
be placed on the same surface as the server. This is especially important for impact printers whose
vibrations could damage the hard disk.
! CAUTION
Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on
power, telephone, and communication cables. Turn off the server and disconnect the power cord,
telecommunications systems, networks, and modems attached to the server before opening it.
Otherwise, personal injury or equipment damage can result.
! CAUTION
Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards, and other
parts. We recommend that you perform all procedures in chapter 3 only at an ESD workstation. If one
is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis
ground ‑ any unpainted metal surface ‑ on your server when handling parts.
! ATTENTION
In order to fully separate the server from current, the power cord must be removed from the wall
outlet.

6 7MAXDATA PLATINUM 100 I M9Setting up the System
6 7MAXDATA PLATINUM 100 I M9Setting up the System
System Access Warnings
! CAUTION
To avoid personal injury or property damage, the following safety instructions apply whenever accessing
the inside of the product:
• Turn off all peripheral devices connected to this product.
• Turn off the system by pressing the power button to off.
• Disconnect the AC power by unplugging all AC power cords from the system or wall outlet.
• Disconnect all cables and telecommunication lines that are connected to the system.
• Retain all screws or other fasteners when removing access cover(s). Upon completion of
accessing inside the product, refasten access cover with original screws or fasteners.
• Do not access the inside of the power supply. There are no serviceable parts in the power
supply. Return to manufacturer for servicing.
• Power down the server and disconnect all power cords before adding or replacing any non hot‑
plug component.
• When replacing a hot‑plug power supply, unplug the power cord to the power supply being
replaced before removing the power supply from the server.
! CAUTION
If the server has been running, any installed processor(s) and heat sink(s) may be hot. Unless you
are adding or removing a hot‑plug component, allow the system to cool before opening the covers.
To avoid the possibility of coming into contact with hot component(s) during a hotplug installation,
be careful when removing or installing the hot‑plug component(s).
! CAUTION
To avoid injury do not contact moving fan blades. If your system is supplied with a guard over the
fan, do not operate the system without the fan guard in place.

6 7MAXDATA PLATINUM 100 I M9Setting up the System
6 7MAXDATA PLATINUM 100 I M9Setting up the System
Connecting the System
Back Panel Connectors
Figure 1. Back Panel Connectors
A. System Identification LED H. Diagnostic LED 2
B. Status LED I. Diagnostic LED 1
C. Diagnostic LED 7 (MSB LED) J. Diagnostic LED 0 (LSB LED)
D. Diagnostic LED 6 K. Serial Port A
E. Diagnostic LED 5 L. Video Port
F. Diagnostic LED 4 M. NIC 1 (top, default management port),
two USB ports (bottom)
G. Diagnostic LED 3 N. NIC 2 (top), two USB ports (bottom)
The NIC LEDs at the right and left of each NIC provide the following information.
Table 1. NIC LEDs
LED LED State Description
Left Off No network connection
Solid Green Network connection in place
Blinking Green Transmit/receive activity
Right Off 10 Mbps connection (if left LED is on or blinking)
Solid Green 100 Mbps connection
Solid Amber 1000 Mbps connection
A
BDF
CEG
H
I
J
K L MN

8 PBMAXDATA PLATINUM 100 I M9Setting up the System
Powering up the System
At the front of the case, you can find the necessary controls like power button and the HDD LEDs.
Press the power button one time briefly in order to boot the server.
Figure 2. PLATINUM 100 I Controls
A. Front USB ports
B. Power switch
C. Power LED
D. Reset switch
E. HDD LED
A
B
C
D
E

PB 9MAXDATA PLATINUM 100 I M9Server Features
2 Server Features
This chapter briefly describes the main features of the server system. This chapter provides a list of
server system features and diagrams showing the location of important components and connections
of the server system.
Table 2 summarizes the features of the server system.
Table 2. Feature Summary
Feature Description
Chassis Dimensions 450 mm high
195 mm wide
501 mm deep
18.0 kg max. chassis weight
Processor • Support for one Intel®Xeon®3400 Series Processor
• LGA 1156 socket
Memory Two memory channels with support for 1066/1333 MHz ECC Unbuff-
ered DDR3 DRAM (UDIMM) or ECC Registered DDR3 DRAM (RDIMM,
Intel®Xeon®3400 Series only).
• Up to 2 UDIMMs or 3 RDIMMs (Intel®Xeon®3400 Series only) per
channel
• 32 GB max with x8 ECC RDIMM (2 Gbit DRAM) and 16 GB max with
x8 ECC UDIMM (1 Gbit DRAM)
Chipset • Intel®3420 Chipset Platform Controller Hub (PCH)
• ServerEngines LLC Pilot II BMC controller (Integrated BMC)
Peripheral Interfaces External connections:
• One DB-15 graphics port
• One DB-9 serial port A
• Two RJ45 network ports for 10/100/1000 Mbps
• Four USB 2.0 ports (back panel)
• Two USB 2.0 ports (front)
Internal connections:
• One 2x5 USB connector for two USB 2.0 ports
• One vertical type A USB connector
• One 2x5 connector for serial port B
• Six SATA-II ports with integrated RAID support
(Matrix Storage RaidTechnology, Raid 0, 1, 5, 10)
• One port for a remote management module 3 (optional)
Video On-board controller ServerEngines LLC Pilot II with integrated 2D video
controller, 64 MB DDR2 memory, 8 MB of which is graphics memory
LAN • One Gigabit Ethernet 82574L controller
• One Gigabit Ethernet 82578DM controller
Expansion Capabilities • Slot 1: 5V PCI 32 bit / 33 MHz
• Slot 2: PCI Express Gen1 x4 (x1 connection, optional)
• Slot 3: PCI Express Gen1 x8 (x4 connection)
• Slot 4: PCI Express Gen2 x8 (x4 connection, optional)
• Slot 5: PCI Express Gen2 x8 (x8 connection)
• Slot 6: PCI Express Gen2 x16 (x8 connection)
Hard Drives • up to four SATA-II hard drives
• up to two internal SATA hard drives
• support for optional 3x hot-swap drive cage (occupies two
5,25” bays)
• support for optional internal 4x drive cage
Power supply Efficient 300 W power supply (80 PLUS®)
Fans Support for two system fans and one processor fan
System Management Integrated IPMI 2.0-compliant baseboard management controller
• Support for remote management module 3 (“KVM over IP”, optional)
• Support for system management software

10 11MAXDATA PLATINUM 100 I M9Server Features
10 11MAXDATA PLATINUM 100 I M9Server Features
Connector and Header Locations
Figure 3 shows the approximate location of the major components on board.
Figure 3. Board Connector and Component Locations
Table 3. Board Connectors and Components
Label Description Label Description
A. Slot 1, 32 Mbit/33 MHz PCI S. CPU fan connector
B. Slot 2, PCI Express Gen1 x1
(x4 connector, optional)
T. USB SSD connector
C. Intel RMM3 connector (optional) U. SAS module connector (optional)
D. Slot 3, PCI Express Gen1 x4
(PCI Express Gen2 compliant)
V. System fan 1
E. Slot 4, PCI Express Gen2 x4
(x8 connector, optional)
W. IPMB
F. Slot 5, PCI Express Gen2 x8 (x8 connector) X. SATA_SGPIO
G. Slot 6, PCI Express Gen2 x8 (x16 connector) Y. HSBP
H. CMOS battery Z. Type A USB port
I. Ethernet and dual USB combo AA. SATA port 0
J. Ethernet and dual USB combo BB. SATA port 3
K. System fan 4 CC. SATA port 1
L. Video port DD. SATA port 4
M. External serial port EE. SATA port 2
N. Main power connector FF. SATA port 5
O. CPU power connector GG. USB connectors
P. System fan 3 HH. Front panel connector
Q. System fan 2 II. Internal serial port
R. CPU socket
CC
DD
A B C DE F G H IJK
L M
N
O
Q
R
S
T
U
V
W
X
Y
Z
AA
BB
P
DIMM_A3
DIMM_A2 DIMM_B2
DIMM_B3
DIMM_A1 DIMM_B1
EE
FF
GG
HH
II

10 11MAXDATA PLATINUM 100 I M9Server Features
10 11MAXDATA PLATINUM 100 I M9Server Features
Configuration Jumpers
Figure 4 shows the location of the configuration jumpers.
Figure 4. Configuration Jumpers
SSI Front Panel Connector
The server board provides a 24‑pin SSI front panel connector. The following figure shows the pin‑out
for this connector.
Figure 5. SSI Front Panel Connector
A. Power LED D. Reset Button
B. HDD LED E. NIC1 LED
C. Power Button F. NIC2 LED
3
2
J1F5
3
2
J1F2
3
2
J1F3
3
2
J1F1
3
2
J1A2
A
B
C
D
E
F
BMC
Force
Update
Default
CMOS
Clear
Password
Clear
BIOS
Recovery
ME
Force
Update
Enabled
Default
Enabled
Default
Recover
Default
Password
Clear
Default
CLEAR
CMOS

12 PBMAXDATA PLATINUM 100 I M9Server Features
Hardware Requirements
To avoid integration difficulties and possible board damage, your system must meet the requirements
outlined below.
Processor
The mainboard supports one Intel®Xeon®3400 series processor with up to 95 W Thermal Design
Power (TDP) with 2.5 GT/s.
Memory
The server board supports two memory channels with up to three DIMM sockets per channel. The
minimal memory population is one DIMM in memory slot DIMM_A1. Matching pairs of DIMMs
accross channels is recommended (e.g. DIMM_A2 ‑ DIMM_B2). Within a channel DIMM sockets
with a lower number must be populated before sockets with a higher number.
Supported Memory Modules
• 1.5 V DDR3 DIMMs, registered (RDIMMs) or unbuffered (UDIMMs)
• Mixing of RDIMMs and UDIMMs is not permitted
• The following DIMM and DRAM technologies are supported:
• RDIMMs:
‑ Single, dual and quad rank
‑ x8 DRAM with 2 Gbit technology
‑ DDR3 1333 (only single and dual rank), DDR3 1066 and DDR3 800
• UDIMMs:
‑ Single and dual rank
‑ x8 DRAM with 2 Gbit technology
‑ DDR3 1333, DDR3 1066 and DDR3 800
Optional Hardware
Remote Management Module
The Remote Management Module provides extended functions for server management.
A network card is provided specifically for remote access.

PB 13MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
3 Hardware Installations and Upgrades
BeforeYou Begin
Before working with your server product, pay close attention to the “Safety Information” at the
beginning of this manual.
Tools and Supplies Needed
• Phillips (cross head) screwdriver (#1 bit and #2 bit)
• Needle nosed pliers
• Antistatic wrist strap and conductive foam pad (recommended)
Installing or Replacing a Processor
/ NOTE
Use the instructions provided below to install or replace a processor instead of using the instructions
that came with the processor.
When installing a second processor, verify that the processors are identical and of the same voltage
and speed. Do not mix processors of different types or frequencies.
 CAUTIONS
Processor must be appropriate: You may damage the server board if you install a processor that
is inappropriate for your server.
ESD and handling processors: Reduce the risk of electrostatic discharge (ESD) damage to the
processor by doing the following: (1) Touch the metal chassis before touching the processor or server
board. Keep part of your body in contact with the metal chassis to dissipate the static charge while
handling the processor. (2) Avoid moving around unnecessarily.
Installing a Processor
1. Observe the safety and ESD precautions above and at the beginning of this book.
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Disconnect the AC power cord from the server.
4. Remove the server‘s cover.
5. Locate the processor socket (see Figure 3 on page 10).
6. Disconnect and remove any components necessary to access the processor socket.
7. Push down the lever on the processor socket. While pushing downward, push it away from
the socket to release it from the hook. Open the socket lever completely. See figure 6.
Figure 6. Opening the Processor Socket Lever
REMOVE
AF003186
Grosse Point Server Board
AF003186.ai
11 May 2009
Heideman Assoc.
A
B

14 15MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
14 15MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
8. Push the rear tab with your fingertip to bring the front end of the load plate up slightly. Open
the load plate completely. See figure 7.
Figure 7. Opening Load Plate
9. If there is a protective covering on the load plate, remove it and store it for later use.
Figure 8. Removing Protective Covering from the Load Plate
10. Take the processor out of the box and remove the protective shipping covering.
11. Align the processor with the socket in such a way that both notches match up with the
processor socket pins. Gently insert the processor into the socket.
Figure 9. Inserting the Processor
REMOVE
AF003187
Grosse Point Server Board
AF003187.ai
11 May 2009
Heideman Assoc.
REMOVE
A
B
AF003188
Grosse Point Server Board
AF003188.ai
11 May 2009
Heideman Assoc.
REMOVE
AF003190
Grosse Point Server Board
AF003190.ai
11 May 2009
Heideman Assoc.
A

14 15MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
14 15MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
12. Close the load plate (see letter “A”), close the socket lever, and ensure the load plate tab
engages under the socket lever when fully closed (see letter “B” and “C”).
Figure 10. Closing Load Plate and Socket Lever
13. Attach the heat sink (see next page).
AF003191
Grosse Point Server Board
AF003191.ai
11 May 2009
Heideman Assoc.
AB
D
C

16 17MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
16 17MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
Installing the Heat Sink
The heat sink has Thermal Interface Material (TIM) located on the bottom of it. Use caution when
you unpack the heat sink so you do not damage the TIM.
1. Set the heat sink over the processor, lining up the four captive screws with the four posts
surrounding the processor.
2. Loosely screw in the captive screws on the heat sink corners in a diagonal manner.
Do no fully tighten one screw before tightening another.
3. Gradually and equally tighten each captive screw until each is firmly tightened.
Figure 11. Installing the Heat Sink
4. Reinstall and reconnect any parts you removed or disconnected to reach the processor sockets.
5. Replace the server‘s cover and reconnect the AC power cord.
23
1
4

16 17MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
16 17MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
Removing a Processor
1. Observe the safety and ESD precautions at the beginning of this book.
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Remove the AC power cord from the server.
4. Remove the server‘s cover.
5. Loosen the four captive screws on the corners of the heat sink.
6. Twist the heat sink slightly to break the seal between the heat sink and the processor.
7. Lift the heat sink from the processor. If it does not pull up easily, twist the heat sink again. Do
not force the heat sink from the processor. Doing so could damage the processor.
8. Lift the processor lever.
9. Raise the CPU load plate.
10. Remove the processor.
11. If installing a replacement processor, see “Installing the Processor”. Otherwise, install the
protective socket cover over the empty processor socket and reinstall the chassis cover.
Installing a PCI Card
Peripherals and add‑in cards are not included in your system and must be purchased separately.
The PCI slots support full‑height add‑in cards or low‑profile PCI add‑in cards. If a low profile card is
installed in the standard full‑height riser card, it must be equipped with a standard full‑height PCI
mounting bracket.
1. Observe the safety and ESD precautions at the beginning of this book.
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Remove power from your system by unplugging the AC power cord.
4. Remove the chassis cover.
5. Remove the screw that attaches the PCI bracket shield to the rear of the chassis to remove
the shield. Retain the screw.
6. Insert the PCI card into the PCI slot.
7. Use the screw removed in step 5 to secure the PCI card to the chassis.
8. Reconnect or replace any internal components you needed to disconnect or remove.
9. Replace the server’s cover. Reconnect any external components you needed to disconnect.
10. Attach the AC power cord.

18 19MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
18 19MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
Installing and Removing Memory
The silkscreen on the board for the DIMMs displays DIMM_A3, DIMM_A2, DIMM_A1, DIMM_B3,
DIMM_B2, DIMM_B1 starting from the center of the board. DIMM A3 is the socket closest to the
processor socket. See chapter 2 – „Memory“ for a discussion of the memory requirements.
Installing DIMMs
To install DIMMs, follow these steps:
1. Observe the safety and ESD precautions at the beginning of this book.
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Disconnect the AC power cord.
4. Remove the server‘s cover.
5. Locate the DIMM sockets (see figure 3).
Figure 12. Installing DIMMs
6. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open
position.
7. Holding the DIMM by the edges, remove it from its anti‑static package.
8. Position the DIMM above the socket. Align the small notch in the bottom edge of the DIMM
with the keys in the socket (see inset in Figure 12).
9. Insert the bottom edge of the DIMM into the socket.
10. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips
snap into place. Make sure the clips are firmly in place.
11. Reconnect or replace any internal components you needed to disconnect or remove.
12. Replace the server’s cover. Reconnect any external components you needed to disconnect.
13. Attach the AC power cord.

18 19MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
18 19MAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades
Replacing the Backup Battery
The lithium battery on the server board powers the RTC for up to 10 years in the absence of power.
When the battery starts to weaken, it loses voltage, and the server settings stored in CMOS RAM in
the RTC (for example, the date and time) may be wrong. Contact your customer service representative
or dealer for a list of approved devices.
! WARNING
Dangerofexplosionifbatteryisincorrectlyreplaced.Replaceonlywiththesameorequivalent
type recommended by the equipment manufacturer. Discard used batteries according to
manufacturer’sinstructions.
! WARNUNG
Wenneine ungeeignete Batterie eingesetztwird oder die Batteriefalsch eingesetzt wird,
bestehtExplosionsgefahr.ErsetzenSieverbrauchteBatteriennurdurchBatteriengleichen
oderäquivalentenTyps,dervomHerstellerempfohlenwurde.EntsorgenSiedieverbrauchte
BatterieentsprechenddenAnweisungendesHerstellers.
! AVERTISSEMENT
Dangerd’explosionencasderemplacementincorrectdelapile.Remplacez-launiquement
parunepiledumêmetypeoud’untypeéquivalentrecommandéparlefabricant.Mettezau
rebutlespilesusagéesenvousconformantauxinstructionsdufabricant.
! OSTRZEŻENIE
Nieprawidłowa wymiana baterii grozi eksplozją. Wymieniać tylko na taki sam lub
równoważnytyp,zalecanyprzezproducenta.Zużytebaterieutylizowaćzgodniezinstrukcjami
producenta.
! ADVARSEL
Lithiumbatteri-Eksplosionsfarevedfejlagtighåndtering.Udskiftningmåkunskemedbatteri
afsammefabrikatogtype.Levérdetbrugtebatteritilbagetilleverandøren.
! ADVARSEL
Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kunbatterisomanbefalt av
apparatfabrikanten.Bruktbatterireturneresapparatleverandøren.
! VARNING
Explosionsfaravid felaktigt batteribyte. Använd samma batterityp elleren ekvivalent typ
somrekommenderas av apparattillverkaren.Kassera använt batteri enligt fabrikantens
instruktion.
! VAROITUS
Paristovoiräjähtää,josseonvirheellisestiasennettu.Vaihdaparistoainoastaanlaitevalmistajan
suosittelemaantyyppiin.Hävitäkäytettyparistovalmistajanohjeidenmukaisesti.

20 PBMAXDATA PLATINUM 100 I M9Hardware Installations and Upgrades20
To replace the battery, follow these steps:
1. Observe the safety and ESD precautions in “Safety Information”.
2. Turn off all peripheral devices connected to the server. Turn off the server.
3. Disconnect the AC power cord from the server.
4. Remove the server‘s cover and locate the battery.
5. Lift the battery retention mechanism (see Figure 13).
6. Remove the battery from its socket.
Figure 13. Removing the Battery
7. Dispose of the battery according to local ordinance.
8. Remove the new lithium battery from its package, and, being careful to observe the correct
polarity, insert it in the battery socket.
9. Close the chassis.
10. Run Setup to restore the configuration settings to the RTC.
AF003185
Grosse Point Server Board
AF003185.ai
11 May 2009
Heideman Assoc.