MAXDATA PLATINUM 50 I M1 User manual

User’s Manual
MAXDATA PLATINUM 50 I M1

2 3MAXDATA PLATINUM 50 I M1Contents
2 3MAXDATA PLATINUM 50 I M1Contents

2 3MAXDATA PLATINUM 50 I M1Contents
2 3MAXDATA PLATINUM 50 I M1Contents
Contents
1 Setting up the System 5
Server Position ........................................................................................................................................5
Connecting the System ...........................................................................................................................6
Rear Connectors .................................................................................................................................6
Powering up the System .........................................................................................................................6
2 Board Features 7
Board Components .................................................................................................................................8
Processor ................................................................................................................................................9
Main Memory ..........................................................................................................................................9
Hi-Speed USB 2.0 Support ......................................................................................................................9
Enhanced IDE Interface .........................................................................................................................10
Serial ATA ..............................................................................................................................................10
3 Installing and Replacing Board Components 11
Before You Begin ..................................................................................................................................11
Installation Precautions .........................................................................................................................11
Installing a Processor ............................................................................................................................12
Installing a Processor .......................................................................................................................12
Installing Memory ..................................................................................................................................15
Installing DIMMs ..............................................................................................................................16
Installing and Removing a PCI Express Card .........................................................................................16
Installing a PCI Express Card ............................................................................................................16
Configuring the System for Intel® Matrix Storage Technology for Serial ATA .......................................17
Configuring the BIOS for Intel® Matrix Storage Technology ............................................................17
Creating your RAID set .....................................................................................................................17
Loading the Intel® Application Accelerator Drivers ...........................................................................17
Setting Up a “RAID Ready” System ................................................................................................18
Mainboard Configuration Jumpers ........................................................................................................18
Clear RTC RAM (CLRTC1) ................................................................................................................18
CPU fan pin selection (3-pin FM_CPU1, FM_CPU2) ........................................................................19
Gigabit LAN controller setting (3-pin LAN_EN1) ...............................................................................19
VGA graphics controller setting (3-pin VGA_EN1) ............................................................................20
RAID select setting (3-pin RAID_SEL1) ............................................................................................20
BIOS recovery (3-pin RECOVERY1) ..................................................................................................21
Replacing the Battery ............................................................................................................................22
BIOS ......................................................................................................................................................25
Using the BIOS Setup Program .......................................................................................................25
AMI BIOS beep codes ...........................................................................................................................25
4 Regulatory and Integration Information 27
Product Regulatory Compliance ............................................................................................................27
Product Safety Compliance ..............................................................................................................27
Product EMC Compliance ....................................................................................................................27
Product Regulatory Compliance Markings ............................................................................................27
Electromagnetic Compatibility Notices .................................................................................................27
Europe (CE Declaration of Conformity) ............................................................................................27
Product RoHS Compliance ....................................................................................................................27
Installation Requirements ......................................................................................................................28
Prevent Power Supply Overload ......................................................................................................28
Place Battery Marking ......................................................................................................................28
Use Only for Intended Applications .......................................................................................................28

4 MFMAXDATA PLATINUM 50 I M1Contents
Figures
1. Rear connectors ................................................................................................................................6
2. PLATINUM 50 I Controls ...................................................................................................................6
3. Board Components ...........................................................................................................................8
4. Lift Socket Lever ............................................................................................................................12
5. Lift the Load Plate and Don’t Touch the Socket Contacts ..............................................................12
6. Remove the Protective Socket Cover .............................................................................................13
7. Remove the Processor from the Protective Processor Cover and Do Not Touch ..........................13
8. Install Processor ..............................................................................................................................14
9. Close the Load Plate .......................................................................................................................14
10. Dual Configuration Example 1 .........................................................................................................15
11. Dual Configuration Example 2 .........................................................................................................15
12. Installing a DIMM ............................................................................................................................16
13. Clear RTCRAM ................................................................................................................................18
14. FM CPU Setting ..............................................................................................................................19
15. LAN_EN1Setting .............................................................................................................................19
16. VGA Setting .....................................................................................................................................20
17. RAID_SEL1 Setting .........................................................................................................................20
18. BIOS Recovery Setting ....................................................................................................................21
19. Removing the Battery .....................................................................................................................24
Tables
1. Feature Summary ..............................................................................................................................7
2. Board Components ...........................................................................................................................8
3. NIC LEDs ...........................................................................................................................................9
4. Recommended memory configurations ............................................................................................9
5. Serial ATA hard disk drive connection .............................................................................................18
6. AMI BIOS beep codes ....................................................................................................................25
7. Product Certification Markings ........................................................................................................27

MF 5MAXDATA PLATINUM 50 I M1Setting up the System
1 Setting up the System
Server Position
Please take note of the following criteria for creating a practical and safe workplace when setting up
your computer:
The system can be used anywhere the temperature is suitable for people. However, rooms
with humidity over 70 %, and dusty or dirty areas are not appropriate. In addition, do not
expose the server to any temperatures over +30 °C or under +10 °C.
Make sure that the cables connecting the server to peripheral devices are not tight.
Make sure that all power and connection cables are positioned so that they are not trip
hazards.
When you save data to your server‘s hard disks or to a floppy disk, they are stored as
magnetic information on the media. Make sure that they are not damaged by magnetic or
electromagnetic fields.
Because the electronics in your computer can be damaged by jarring, no mechanical devices
should be placed on the same surface as the server. This is especially important for impact
printers whose vibrations could damage the hard disk.
ATTENTION
In order to fully separate the server from current, the power cord must be removed from the wall
outlet.
ATTENTION
To ensure stability, the floor stands must be turned outwards.

6 MFMAXDATA PLATINUM 50 I M1Setting up the System
Connecting the System
Rear Connectors
A. Mouse E. Serial port
B. Parallel port F. Video
C. Keyboard G. Broadcom BCM 5753 (Gbit LAN)
D. USB 2.0 ports
Powering up the System
At the front of the case, you can find the necessary controls like power button and the HDD LEDs.
Press the power button one time briefly in order to boot the server.
A. Power switch
B. Power LED
C. HDD LED
D. Key Lock
Figure 1. Rear connectors
A
C F
EG
D
B
Figure 2. PLATINUM 50 I Controls

MF 7MAXDATA PLATINUM 50 I M1Board Features
2 Board Features
This chapter briefly describes the main features of the mainboard.
Table 1 summarizes the major features of the board.
Table 1. Feature Summary
Feature Description
Processors Support for an Intel® Pentium® 4 processor in the LGA775 package with 800
MHz or 1066 MHz front side bus
Memory • Four 240-pin, 1.8 V SDRAM Dual Inline Memory Module (DIMM) sockets
• 667/533 MHz single or dual channel DDR2 SDRAM interface
• Designed to support up to 8 GB of system memory
Chipset Intel® E7230 Chipset consisting of:
• Intel® E7230 Memory Controller Hub (MCH)
• Intel® 82801GR I/O Controller Hub (ICH7-R)
Peripheral Interfaces • Up to eight USB 2.0 ports
Two ports routed to the back panel
Six ports routed to three USB headers
• Four Serial ATA II channels, via the ICH7-R, supporting Intel® Matrix
Storage (RAID 0/1/5/10)
• One IDE interface with ATA-66/100 support
• One diskette drive interface
• One parallel port
• Two serial ports, one on the back panel
• PS/2 keyboard and mouse ports
LAN • One Broadcom BCM5753 PCIe Gigabit Ethernet Controller
(10/100/1000 Mbit/s) with RJ-45 connector
Graphics • ATI® RAGE-XL PCI-based VGA controller
Expansion Capabilities • Two 32 bit / 33 MHz / 5 V PCI bus connectors (PCI 2.3)
• One PCI Express x8 connector (x4 link)
• One PCI Express x16 connector (x8 link)
BIOS AMI BIOS
• Support for SMBIOS
• Rapid BIOS Boot
Power Management • Support for Advanced Configuration and Power Interface (ACPI)
• Suspend to RAM (STR)
• Wake on USB, PCI, PCI Express, PS/2, LAN, and front panel
Server Management Hardware monitor with:
• Six fan sensing inputs used to monitor fan activity
• Remote diode temperature sensing
• Precision Cooling Technology fan speed control that automatically
adjusts processor fan speeds based on processor temperature and
chassis fan speeds based on system temperature
• Voltage sensing to detect out of range values

8 9MAXDATA PLATINUM 50 I M1Board Features
8 9MAXDATA PLATINUM 50 I M1Board Features
Board Components
Figure 3 shows the approximate location of the major components on board.
Table 2. Board Components
Label Description Label Description
A. Rear Fan 1 S. SATA 4
B. Rear Fan 2 T. SATA 3
C. Conventional PCI Slot 2 U. SATA 2
D. Conventional PCI Slot 1 V. SATA 1
E. PCIE Slot 2 (x8 Connector, x4 Link) W. HDD LED 1
F. PCIE Slot 1 (x16 Connector, x8 Link) X. Front Fan 2
G. Back Panel I/O Y. Front Fan 1
H. ATX 12 V Z. Backplane SMBus
I. LGA775 Processor Socket AA. Ambient Thermal Sensor
J. Channel A DIMM 1 Socket (blue) BB. USB 2.0 Ports 7/8
K. Channel A DIMM 2 Socket (black) CC. USB 2.0 Ports 5/6
L. CPU Fan 2 DD. USB 2.0 Ports 3/4
M. Channel B DIMM 1 Socket (blue) EE. Battery
N. Channel B DIMM 2 Socket (black) FF. COM2
O. CPU Fan 1 GG. Chassis Intrusion Connector
P. Diskette Drive HH. Front Panel Connector
Q. IDE II. Standby Power LED
R. ATX Power 1
Figure 3. Board Components
DIM
M
_B1
DIM
M
_A1
DIMM_A2
DIMM
_B2
A B D
CEFG
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
AA
BB
CC
DD
EE
FF
GG
HH
II
PCI 1
PCI 2
PCIE 1
PCIE 2

8 9MAXDATA PLATINUM 50 I M1Board Features
8 9MAXDATA PLATINUM 50 I M1Board Features
The NIC LEDs at the right and left of the NIC provide the following information:
Table 3. NIC LEDs
LED Color LED State Description
Left LED Off No network connection
Green Network connection in place
Blinking Transmit/receive activity
Right LED Off 10 Mbps connection (if left LED is on or blinking)
Red 100 Mbps connection
Green 1000 Mbps connection
Processor
The board supports a single Intel® Pentium® 4 Processor in the LGA775 package.
CAUTION
Failure to use an ATX12V power supply or not connecting the 12 V (2 × 2) power connector to the
mainboard may result in damage to the board and/or power supply.
Main Memory
The mainboard supports dual or single channel memory configurations defined in Table 4. 256 MB,
512 MB, 1 GB, and 2 GB unbuffered ECC/non-ECC DDR2 533/667 MHz DIMMs can be installed.
 NOTE
When installing one or two DIMMs, install the DIMM(s) to the blue slots (DIMM_A2/DIMM_B2). Use
only identical DDR2 DIMM pairs for Dual channel configurations.
Table 4. Recommended memory configurations
Mode DIMM_A1 (blue) DIMM_A2 (black) DIMM_B1 (blue) DIMM_B2 (black)
Single-channel Installed – – –
Dual-channel* Installed – Installed –
Installed Installed Installed Installed
* Use only identical DDR2 DIMM pairs.
 NOTE
System resources (such as PCI and PCI Express) require physical memory address locations that
reduce available memory addresses above 3 GB. As a result of this, less than the installed memory
may be available to the operating system and applications if more than 3 GB of memory are installed
in the system.
Hi-Speed USB 2.0 Support
 NOTE
Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class
B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded
cable that meets the requirements for a full-speed USB device.
The board supports up to eight USB 2.0 ports via ICH6-R; four ports routed to the back panel and
four routed to two internal USB 2.0 headers. USB 2.0 ports are backward compatible with USB 1.1
devices. USB 1.1 devices will function normally at USB 1.1 speeds.
USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer
rates. Disabling Hi-Speed USB in BIOS reverts all USB 2.0 ports to USB 1.1 operation. This may be
required to accommodate operating systems that do not support USB 2.0.

10 MFMAXDATA PLATINUM 50 I M1Board Features
Enhanced IDE Interface
The ICH7R’s IDE interface handles the exchange of information between the processor and peripheral
devices like hard disks, CD-ROM drives, and Iomega Zip drives inside the computer. The interface
supports:
• Up to two IDE devices (such as hard drives)
• ATAPI-style devices (such as CD-ROM drives)
• Older PIO Mode devices
• Ultra DMA-33 and ATA-66/100 protocols
• Laser Servo (LS-120) drives
Serial ATA
The board supports four Serial ATA channels via the ICH7R, connecting one device per channel in
either a RAID or non-RAID configuration.

MF 11MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
3 Installing and Replacing Board Components
Before You Begin
WARNING
The procedures in this chapter assume familiarity with the general terminology associated with
personal computers and with the safety practices and regulatory compliance required for using and
modifying electronic equipment.
Disconnect the computer from its power source and from any telecommunications links, networks,
or modems before performing any of the procedures described in this chapter. Failure to disconnect
power, telecommunications links, networks, or modems before you open the computer or perform
any procedures can result in personal injury or equipment damage. Some circuitry on the board can
continue to operate even though the front panel power button is off.
Follow these guidelines before you begin:
• Always follow the steps in each procedure in the correct order.
• Set up a log to record information about your computer, such as model, serial numbers,
installed options, and configuration information.
• Electrostatic discharge (ESD) can damage components. Perform the procedures described in
this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam
pad. If such a station is not available, you can provide some ESD protection by wearing an
antistatic wrist strap and attaching it to a metal part of the computer chassis.
Installation Precautions
When you install or exchange hardware components, observe all warnings and cautions in the
installation instructions.
To avoid injury, be careful of:
• Sharp pins on connectors
• Sharp pins on printed circuit assemblies
• Rough edges and sharp corners on the chassis
• Hot components (like processors, voltage regulators, and heat sinks)
• Damage to wires that could cause a short circuit
Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical
personnel.
 NOTE
The motherboard comes with a standby power LED. The green LED lights up to indicate that the
system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the
system and unplug the power cable before removing or plugging in any motherboard component.

12 13MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
12 13MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
Installing a Processor
Instructions on how to install the processor to the board are given below.
Installing a Processor
CAUTION
Before installing or removing the processor, make sure that AC power has been removed by unplugging
the power cord from the computer; the standby power LED should not be lit Failure to do so could
damage the processor and the board.
To install a processor, follow these instructions:
1. Observe the precautions in “Before You Begin”.
2. Open the socket lever by pushing the lever down and away from the socket (see Figure 4, A
and B).
3. Lift the load plate. Do not touch the socket contacts (see Figure 5, C and D)





Figure 4. Lift Socket Lever
Figure 5. Lift the Load Plate and Don’t Touch the Socket Contacts

12 13MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
12 13MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
4. Remove the protective socket cover from the load plate. Do not discard the protective socket
cover. Always replace the socket cover if the processor is removed from the socket (see
Figure 6, E).
5. Remove the processor from the protective processor cover. Hold the processor only at the
edges, being careful not to touch the bottom of the processor. Do not discard the protective
processor cover. Always replace the processor cover if the processor is removed from the
socket (see Figure 7).
Figure 6. Remove the Protective Socket Cover
�
Figure 7. Remove the Processor from the Protective Processor Cover and Do Not Touch

14 15MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
14 15MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
6. Hold the processor with your thumb and index fingers oriented as shown in Figure 8. Make
sure fingers align to the socket cutouts (see Figure 8, F). Align notches (see Figure 8, G) with
the socket see (Figure 8, H). Lower the processor straight down without tilting or sliding the
processor in the socket.
7. Pressing down on the load plate (Figure 9, I) close and engage the socket lever (Figure 9, J).
Figure 8. Install Processor






Figure 9. Close the Load Plate



14 15MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
14 15MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
Installing Memory
The board has four 240-pin DIMM sockets arranged as DIMM 1 and DIMM 2 in both Channel A and
Channel B, as shown in Figure 3.
Guidelines for Dual Channel Memory Configuration
Before installing DIMMs, read and follow these guidelines for dual channel configuration.
Two or Four DIMMs
Install a matched pair of DIMMs equal in speed and size (see Figure 10) in DIMM 1 (blue) of both
channels A and B.
Channel A
1 GB, 533 MHz DIMM 1
DIMM 2
Channel B
1 GB, 533 MHz DIMM 1
DIMM 2
If additional memory is to be used, install another matched pair of DIMMs in DIMM 2 (black) in both
channels A and B (see Figure 11).
Channel A
256 MB, 533 MHz DIMM 1
512 MB, 533 MHz DIMM 2
Channel B
256 MB, 533 MHz DIMM 1
512 MB, 533 MHz DIMM 2
Figure 10. Dual Configuration Example 1
Figure 11. Dual Configuration Example 2
Figure 8. Install Processor
Figure 9. Close the Load Plate

16 17MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
16 17MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
Figure 12. Installing a DIMM
Installing DIMMs
To install DIMMs, follow these steps:
1. Observe the precautions in “Before You Begin” on page 11.
2. Turn off all peripheral devices connected to the computer. Turn off the computer and
disconnect the AC power cord.
3. Remove the computer’s cover and locate the DIMM sockets (see figure 3).
4. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open
position.
5. Holding the DIMM by the edges, remove it from its anti-static package.
6. Position the DIMM above the socket. Align the small notch at the bottom edge of the DIMM
with the keys in the socket (see Figure 12).
7. Insert the bottom edge of the DIMM into the socket.
8. When the DIMM is inserted, push down on the top edge of the DIMM until the retaining clips
snap into place. Make sure the clips are firmly in place.
9. Replace the computer’s cover and reconnect the AC power cord.
Installing and Removing a PCI Express Card
CAUTION
When installing any PCI Express card on the board, ensure that it is fully seated in the PCI Express
connector before you power on the system. If the card is not fully seated in the PCI Express connector,
an electrical short may result across the PCI Express connector pins. Depending on the over-current
protection of the power supply, certain board components and/or traces may be damaged.
Installing a PCI Express Card
Follow these instructions to install a PCI Express card:
1. Observe the precautions in “Before You Begin”.
2. Place the card in the PCI Express connector.
3. Press down on the card until it is completely seated in the connector.
4. Secure the card’s metal bracket to the chassis back panel with a screw.

16 17MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
16 17MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
Figure 12. Installing a DIMM
Configuring the System for Intel® Matrix Storage Technology
for Serial ATA
Configuring the BIOS for Intel® Matrix Storage Technology
1. Assemble your system and attach two SATA hard drives.
2. Enter system BIOS Setup by pressing the <F2> key after the Power-On-Self-Test (POST)
memory tests begin.
3. Go to “Main” > “IDE Configuration”; make sure “Configure SATA As” is set to “RAID”.
4. Then save your settings by pressing <F10>.
Creating your RAID set
1. Upon re-boot you will see the Intel® Matrix Storage Manager Option ROM status message on
the screen. Press CTRL-I to enter the RAID Option ROM user interface.
2. In the User Interface menu, select option #1; Create RAID Volume. Enter a volume name,
press <enter>.
 NOTE
The RAID Volume name must be in English alphanumeric ASCII characters.
3. Use the arrow keys to select RAID 0 or RAID 1, press <enter>.
4. Select the drives to be used in the RAID array (only if there are more than two drives available),
press <enter>.
5. Select the stripe size (only for RAID 0), and press <enter>.
6. Enter the size of the volume (If you select less than the maximum volume size you can then
create a second RAID array on the remaining portion of your volume), and press <enter>.
7. Finally press <Y> to confirm your selections.
8. Exit the Option ROM user interface by pressing <esc>.
Loading the Intel® Application Accelerator Drivers
 NOTE
A floppy disk with the RAID driver is required when installing the operating system on a RAID set.
You can create a RAID driver disk from the mainboard resource CD. Either boot the CD and follow
the instructions on the screen or run the program located in the drivers directory under Windows to
create the driver disk.
1. Begin Microsoft® Windows® Setup by booting from the Microsoft® Windows® installation CD.
2. At the beginning of Microsoft® Windows® Setup, press <F6> to install a third-party SCSI or
RAID driver. When prompted, insert the floppy disk with the RAID driver. Install the Intel®
82801GR/GH SATA RAID Controller driver.
3. Finish the Microsoft® Windows® installation and install all necessary drivers.
4. Install the Intel® Application Accelerator software via the Intel® Express Installer CD included
with your motherboard or after downloading it from the Internet. This will add the Intel®
Storage Utility which can be used to manage the RAID configuration.

18 19MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
18 19MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
Setting Up a “RAID Ready” System
The Intel® Application Accelerator software offers the flexibility to upgrade from a single Serial ATA
drive to RAID without reinstalling the Operating System (OS), when a second SATA hard drive is
added to the system.
Follow the steps described in “Configuring the BIOS for Intel® Matrix Storage Technology” and
“Loading the Intel® Application Accelerator Drivers”.
Table 5. Serial ATA hard disk drive connection
Connector Setting Use
SATA1 / SATA2 Master Boot Disk
SATA3 / SATA4 Slave Data Disk
Mainboard Configuration Jumpers
Clear RTC RAM (CLRTC1)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS
memory of system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell
battery powers the RAM data in CMOS, which include system setup information such as system
passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the onboard battery.
3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5
to 10 seconds, then move the cap back to pins 1-2.
4. Re-install the battery.
5. Plug the power cord and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data.
CAUTION
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position.
Removing the cap will cause system boot failure!
Figure 13. Clear RTCRAM
CLRTC1
2
1
3
2
Normal (Default) ClearCMOS

18 19MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
18 19MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
CPU fan pin selection (3-pin FM_CPU1, FM_CPU2)
These jumpers allow you to connect either a 3-pin or a 4-pin fan cable plug to the CPU fan connectors
(CPU_FAN1, CPU_FAN2). Set these jumpers to pins 1-2 if you are using a 3-pin fan cable plug, or to
pins 2-3 if you are using a 4-pin plug.
FM_CPU1
FM_CPU2
2
3
2
1
212
3
3-pin fan 4-pin fan
(Default)
3-pin fan
Gigabit LAN controller setting (3-pin LAN_EN1)
This jumper allows you to enable or disable the onboard Broadcom BCM5753 Gigabit LAN controller.
Set to pins 1-2 to activate the Gigabit LAN feature.
4-pin fan
(Default)
LAN_EN1
2
123
Enable
(Default)
Disable
Figure 14. FM CPU Setting
Figure 15. LAN_EN1 Setting

20 21MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
20 21MAXDATA PLATINUM 50 I M1Installing and Replacing Board Components
VGA_EN1
2
1
2
3
VGA graphics controller setting (3-pin VGA_EN1)
This jumper allows you to enable or disable the onboard ATI Rage XL video graphics controller. Set
to pins 1-2 to enable the video graphics controller.
Enable (Default)
Figure 16. VGA Setting
Caution
Make sure to set this jumper to Disable if you want to install VGA cards on the PCI and PCI Express
slots.
RAID select setting (3-pin RAID_SEL1)
This jumper must always be installed to 2-3 to enable Intel® RAID ROM. Jumper setting 1-2 is not
supported.
RAID_SEL1
2
1
2
3
(not supported) INTEL RAID ROM
Figure 17. RAID_SEL1 Setting
Disable