Maxkon BBQ Series User manual

Assembly Instructions :
FIREPIT WITH STEEL TABLE TOP:JS-FT139T
Part List
Part List
Description
Qty.
Drawings
A
Top Frame
1
B
Leg
4
C
Frame Support Part
4
D1
Small Log Grate
1
D2
BBR Grill
1
E
Fire Bowl
1
F
Mesh Lid
1
G
Lid Ring
1
H
Bolt (M6x8mm）
20
I
Poker
1
J
Allen Wrench
1
L
Ceramic Tile
8
M
Ice Bowl
1
N
Steel Table Top
1
O
Pancake Turner
1
P
Tong
1
Tool required: Allen Wrench (provided)
Assembly Instructions
Estimated Assembly Time: 20 Minutes
DO NOT over tighten hardware!
Step 1: Place parts on a smooth even surface, Attach Legs (B) to Frame Support Part (C)
with Bolts (H) Hand tighten!
Step 2: Attach Top Frame (A) to Legs (B) by using Bolts (H). Tighten all hardware
accordingly with an Allen Wrench (J) (provided) and adjustable wrench until all pieces fit
together securely. Turn the assembled fire pit frame over so that it sits securely (legs
down) on a flat surface.
Step 3: Place Fire Bowl (E) in the center of Top Frame (A) and put Log Grate (D1) and
Rack (D2) in the Fire bowl (E).Mount Lid Ring (G) on the Mesh Lid (F), then place the
assembled Mesh Lid over the Fire bowl (E) and put Ceramic Tiles (L) on the assembled
frame..

Your FIRE PIT is ready for use!
Step 4 For Table: Put the Steel Table Top (N) onto the assembled firepit frame. Then
Table is ready for using.
Step 5 For BBQ: Put the BBQ Grill (D2) onto the assembled frame. Then BBQ is ready
for cooking.
Step 6 For Cooler
Place the Ice Bowl (M) on the
assemble firepit base. The cooler
is ready for using
WARNING:
FOR OUTDOOR USE ONLY
FOR YOUR SAFETY:
1. Improper installation, adjustment,alteration,service or maintenance
can cause injury or property damage.
2. Read the installation, operation, and maintenance instructions
thoroughtly beforeinstalling or servicing this equipment.
3. Failure to follow these instructions could result in fire or explosion,
which could cause property damage, personal injury, or death.
OPERATING INSTRUCTIONS
Lighting
1. make sure there is only a small amount of ash in the bottom of the bowl.
2. place a layer of dry kindling or a natural firestarter onto the center of the
grate.
3. place above that a layer of dry seasoned hardwood that is cut to lengths no
more than 3/4 the diameter of the bowl.
4. use a match to light kindling or firestarter.
5. using a hook and heat resistant gloves,replace spark guard once the
kindling or firestarter is lit.
Tending the fire
You may need to shift and/or add logs for an ideal experience.
CAUTION: DO NOT place a hot spark guard or hot fire bowl tools onto
combustible surfaces such as grass, wooden deck or furniture.
1. Using a hook and heat resistant gloves, carefully remove spark guard.
2. While using a long handled fire pit tool, shift coals and logs to allow additional
airflow.
3. DO NOT add gasoline, kerosene, diesel fuel, lighter fluid or alcohol to relight or
enhance an existing fire.

4. Wait until glowing coals have developed before adding any additional wood. If
additional wood is required, place wood on top coals. Be careful not to shift
ashes.
5. Using a hook and heat resistant gloves, replace spark guard.
Extinguishing
1. Allow fire to burn itself out.
2. DO NOT use water to extinguish as this is dangerous and can cause damage to
this outdoor fire pit.
CLEANING AND CARE
Inspecting
This outdoor fire pit should be inspected on a regular basis to ensure product safety
and longer product life.
CAUTION: DO NOT attempt to inspect this outdoor fire pit until the fire is
completely out.
1. Check handles to make sure they are secure.
2. Check components for any signs of damage or rust.
3. If damage to any components is detected, DO NOT operate until repairs are
executed.
Cleaning
This outdoor fire pit should be inspected on a regular basis to ensure product safety
and longer product life.
Note: After repeated use, a slight discoloration of the finish may occur.
CAUTION: DO NOT attempt to inspect this outdoor fire pit unitl the fire is
COMPLETELY out.
CAUTION: DO NOT use oven cleaner or abrasive cleaners as they will
damage this product.
CAUTION: DO NOT clean any part of this outdoor fire pit in a self cleaning
oven as it may damage the finish.
1. Wipe exterior surfaces with a mild dishwashing detergent or baking soda.
2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing
brush.
3. Rinse clean with water.
4. Remove built-up creosote from components with a chimney cleaning product.
Storage
CAUTION: DO NOT move or store this outdoor fire pit until the fire is
completely out.
1. Once the fire is out, coals are cold and outdoor fire pit is cool to the touch,
remove ashes and properly dispose.
2. Store assembled in a location away from children and pets.