MAXTON DESIGN SPOILER EXTENSION User manual

Disclaimer
These are fitting guidelines only and we highly recommend installations are undertaken by a professional.
Maxton Design Ltd. can’t be held liable for any damages or liabilities that may arise from following any
guidelines given by the Company.
Vehicle modifications caused by the usage, abuse, or incorrect installation of Maxton Design Ltd. products
might result in significant vehicle malfunction. Vehicle damage, major bodily injury, disability, and/or death are
among the dangers. Any changes you make to your or someone else's car using Maxton Design Ltd. goods are
your responsibility. Maxton Design Ltd. is not responsible for any changes made to automobiles as a result of
the usage or abuse of its product and will not be held accountable. If you have little to no expertise installing
any of the products sold via maxtondesign.co.uk website, professional installation is highly suggested.
Products are sold as-is, and we are not responsible for any damages or injuries sustained during installation or
subsequent use of the vehicle. Because proper installation is crucial to our product's performance and longevity,
please go through the documentation carefully and test your installation before resuming driving.
SPOILER EXTENSION
-INSTALLATION MANUAL-

COMPLETE SET CONTAINS:
- Spoiler Extension
- Mounting Kit
- Mounting Manual
For more Installation Manuals visit
www.maxtondesign.co.uk/fitting-manuals
SPOILER EXTENSION
INSTALLATION MANUAL
Tel: [phone] Email: [email protected].uk Web: maxtondesign.co.uk
Page 2

1
SPOILER EXTENSION
INSTALLATION MANUAL
Tel: [phone] Email: [email protected].uk Web: maxtondesign.co.uk
Page 3
STEP 1
Place the spoiler extension on the spoiler for
the initial fitment testing
2STEP 2
Place masking tape on the cars spoiler around
the edges, this will be used to help mark the
placement of the product.
3STEP 3
Use a measuring tape to find an even distance from the the end of the cars spoiler to the end of
the product on both sides. We recommend you request assistance for this step.

SPOILER EXTENSION
INSTALLATION MANUAL
Tel: [phone] Email: [email protected].uk Web: maxtondesign.co.uk
Page 4
STEP 4
Outline the edges of the spoiler extension on the masking tape before removing.
4
5STEP 5
Lift the spoiler extension and place it to the
side. Use the provided degreasing cloth to
clean the spoiler prior to installation.
6STEP 6
Peel back 2-3cm of the 3M tape cover on one
of the edges of the product.

SPOILER EXTENSION
INSTALLATION MANUAL
Tel: [phone] Email: [email protected].uk Web: maxtondesign.co.uk
Page 5
STEP 7
Align the spoiler extension with the markings
drawn on the masking tape from step 4.
Do not put excessive pressure on the
product at this point as you will need to
further remove the 3m tape.
7
STEP 8
Slowly peel off the remaining 3M tape. Keep
a small amount of pressure on the spoiler
extension throughout this process to stop any
movement from occuring. We recommend
again that you should ask for assistance.
Once this is done you can clamp the
product down or apply downwards pressure
from above to ensure it has a more secure
fit.
8
STEP 9
Now for the most satisfying step, remove the
protective film from the product where
applicable (Carbon look and Gloss black
surface finishes).
9

SPOILER EXTENSION
INSTALLATION MANUAL
Tel: [phone] Email: [email protected].uk Web: maxtondesign.co.uk
Page 6
STEP 10
Use a heat gun to slightly heat the spoiler extension. This will further improve how well the 3M tape
bonds to the car. Be autious not to use excessive heat as it could cause defmorities to the product.
We recommend you keep a 30-40cm disance while completeling this process.
You can now sit back, relax and enjoy your new modification.
10
Please note these instructions are for guidance only. It is your responsibility to ensure
the installation is undertaken in a safe and correct way. We strongly recommend you
leave the installation to a qualified professional.

Thank you for choosing
Maxton Design!
We hope our product will meet your expectations.
Let us know if you have any questions.
7 Gilhusum Road, Leeds, West Yorkshire, LS27 7FN, United Kingdom
[phone]
[e-mail]
www.maxtondesign.co.uk