Maxtor D540X-4K Datasheet

Capacity 80GB Firmware: M206B
Level MP
P/N: 127351
M
A
X
T
O
R
C
O
R
P
O
R
A
T
I
O
N
•
H
A
R
D
D
I
S
K
D
R
I
V
E
•
Q
U
A
L
I
T
Y
•
Jumper Styles B & C
Jumper Style A
or
Included in this Kit
Maxtor ATA Hard Drive
ATA Interface Cable
MaxBlast™ Plus II Diskette
MaxBlast™ Plus II CD
5.25-inch Mounting Brackets
(not included with all kits)
Mounting Screws
Quick Start Poster
Installation Guide
(not included with all kits)
Tools Required
Phillips Screwdriver
Small Needle-Nose Pliers
Operating System
CD and Boot Disk
System User Manual
SystemManual
Max•BlastTMPlus II
HardDrive Installation Software
Drive should be at room
temperature before
installing.
Precautions
About this Poster
Thank you for selecting a
Maxtor hard drive product.
This Quick Start Poster pro-
vides an installation overview
for users who have previous
experience installing a hard
drive.
If you need detailed instructions,
refer to the
Maxtor ATA Hard
Drive Installation Guide
provided
with this kit or included on the
MaxBlast Plus II CD-ROM.
ATA Hard Drive Installation Quick Start
Remove system cover
1
Determine jumper style
Match your drive to the illustration below
to determine jumper style. For styles B
and C, check drive label for the specific
model number.
Style C is used on models
D740X and D540X-4K.
2
INSTALLATION STEPS
Do not connect cables
to drive or motherboard
with system powered on.
Do not drop, bump, or
jar drive.
Do not touch circuit
board on drive.
continued
Note for Macintosh Users
Refer to Macintosh system
documentation or go to
www.apple.com.
Style A
Master
Slave
Cable
Select
Style B
Master
Slave
Cable
Select
Style C
Master
Slave
Cable
Select
(CLJ) Capacity
Limitation
Jumper
Set jumpers
See “Setting the Jumpers”in the Maxtor ATA
Hard Drive Installation Guide
for more details.

DC
Power Connector
Slave
(gray connector)
Power Supply
Cable
Striped Edge
Master
(black connector)
Capacity80GBFirmware:M206B
LevelMP
P/N:127351
M
A
X
T
O
R
C
O
R
P
O
R
A
T
I
O
N
•
H
A
R
D
D
I
S
K
D
R
I
V
E
•
Q
U
A
L
I
T
Y
•
ATA Interface
Cable
Motherboard or PCI Adapter
(blue connector)
Pin 1
Key
Bevel
Key Slot
Mounting
Screws
Mounting
Bracket
Mounting
Screws
Typical 5.25-inch Device Bay Installation
with Mounting Brackets
Typical 3.5-inch Device Bay Installation
Mounting Brackets
See “Formatting the Hard Drive”
in the
Maxtor ATA Hard Drive
Installation Guide
for more details.
Use Apple Drive Setup (classic
Mac OS) or Apple Disk Utility
(Mac OS X)
Mount the drive
Refer to your system
documentation for
more details.
3
Attach the cables
See “Attaching the Cables” in the
Maxtor ATA Hard Drive Installation
Guide
for more details.
4
Set the BIOS (Windows only)
See “Configuring the System BIOS”
in the
Maxtor ATA Hard Drive
Installation Guide
for more details.
5
Restart system with
MaxBlast CD and floppy
Use the MaxBlast Plus II CD
and floppy to partition and
format the drive.
6
Register product
Register your Maxtor drive
at www.maxtor.com
7
INSTALLATION STEPS
Please refer to the Maxtor ATA Hard Drive Installation Guide for warranty information.
Maxtor may make changes or improvements in the product(s) described in this publication at any
time and without notice. This product tested to comply with FCC standards for home or office use.
Copyright © 2002 Maxtor. All rights reserved. MaxBlast is a trademark and Maxtor is a registered
trademark of Maxtor Corporation. Other brands or products are trademarks or registered trademarks of
their respective holders. Maxtor Corporation, 500 McCarthy Blvd., Milpitas, California 95035 U.S.A.
Maxtor p/n: 20186900, rev A
For more help:
•Go to the Maxtor Knowledge Base at
www.maxtor.com/knowledgebase
•Contact Maxtor Technical Support at
www.maxtor.com
Top
Typical BIOS Setup Message