McCulloch T26CS User manual

T26CS
(((( AAAA TTTT 2222 6666 CCCC CCCC MMMM CCCC ))))
GB Operator’s manual 2-22
SE Bruksanvisning 23-43
DK Brugsanvisning 44-64
FI Käyttöohje 65-85
NO Bruksanvisning 86-106
FR Manuel d’utilisation 107-127
NL Gebruiksaanwijzing 138-148
IT Istruzioni per l’uso 149-169
ES Manual de instrucciones 170-191
DE Bedienungsanweisung 192-213
PT Instruções para o uso 214-235
HU Használati utasítás 236-256
PL Instrukcja obs∏ugi 257-278
EE Käsitsemisõpetus 279-299
LV Lieto‰anas pamÇc¥ba 300-321
LT Naudojimosi instrukcijos 322-343
SK Návod na obsluhu 344-365
RS Priruãnik 366-387
HR Priruãnik 388-409
SI Navodila za uporabo 410-431
BA Uputstvo o upotrebi 432-453
CZ Návod k pouÏití 454-475
RU óêîâîäñòâî ïî
ýêñïëóàòàöèè 476-499
BG úêîâîäñòâî çà
åêñïëîàòàöèß 500-525
UA îñ´áíèê êîðèñòóâà÷à 526-550
GR √‰ËÁ›Â˜ ¯Ú‹Ûˆ˜ 551-575
TR Kullanım kılavuzu 576-597
RO Instrucöiuni de utilizare 598-619
S1156009-38,T26CS_1.fm Page 1 Tuesday, November 29, 2016 4:21 PM

KEY TO SYMBOLS
2 – English
Symbols
AT26CCMC
WARNING! A grass trimmer can be
dangerous if used incorrectly or carelessly,
and can cause serious or fatal injury to the
operator or others. It is extremely important
that you read and understand the contents of
this operator’s manual.
Please read the operator’s manual carefully
and make sure you understand the
instructions before using the machine.
Always wear:
• Wear a protective helmet where there is a
risk of falling objects
• Approved hearing protection
• Approved eye protection
This product is in accordance with
applicable EC directives.
Watch out for thrown objects and ricochets.
The operator of the machine must ensure,
while working, that no persons or animals
come closer than 15 meters.
Only use non-metallic, flexible cutting
attachments, i.e.trimmer heads with trimmer
cord.
rrows which show limits for handle
positioning.
Always wear approved protective gloves.
Wear sturdy, non-slip boots.
Make sure your hair does not hang below
shoulder level.
Choke: Set the choke control in the
choke position.
Set the choke control in the RUN position.
Primer bulb
Refuelling.
Noise emission to the environment
according to the European Community’s
Directive.The machine’s emission is
specified in the Technical data chapter and
on the label.
Other symbols/decals on the machine
refer to special certification requirements for certain
markets.
The engine is switched off by moving the
stop switch to the stop position. CAUTION!
The stop switch automatically returns to the
start position. In order to prevent
unintentional starting, the spark plug cap
must be removed from the spark plug when
assembling, checking and/or performing
maintenance.
Always wear approved protective gloves.
Regular cleaning is required.
Visual check.
Approved eye protection must always be
used.
S1156009-38,T26CS_1.fm Page 2 Wednesday, April 6, 2016 1:15 PM

CONTENTS
English – 3
Contents Note the following before
starting:
Please read the operator's manual carefully.
KEY TO SYMBOLS
Symbols ................................................................ 2
CONTENTS
Contents ............................................................... 3
Note the following before starting: ........................ 3
INTRODUCTION
Dear Customer, .................................................... 4
WHAT IS WHAT?
What is what on the grass trimmer? ..................... 5
GENERAL SAFETY PRECAUTIONS
Important .............................................................. 6
Personal protective equipment ............................. 6
Machine′s safety equipment ................................. 7
Cutting equipment ................................................ 9
ASSEMBLY
Fitting the loop handle .......................................... 10
Assembling and dismantling the two-piece shaft 10
Assembling the cutting equipment ....................... 11
Fitting the trimmer guard and trimmer head ......... 11
FUEL HANDLING
Fuel safety ............................................................ 12
Fuel ...................................................................... 12
Fueling .................................................................. 13
STARTING AND STOPPING
Check before starting ........................................... 14
Starting and stopping ........................................... 14
WORKING TECHNIQUES
General working instructions ................................ 16
MAINTENANCE
Carburettor ........................................................... 18
Muffler .................................................................. 18
Cooling system ..................................................... 18
Spark plug ............................................................ 19
Two-piece shaft ................................................... 19
Air filter ................................................................. 19
Checking and adjusting of throttle wire ................ 19
Maintenance schedule ......................................... 20
TECHNICAL DATA
Technical data ...................................................... 21
EC Declaration of Conformity ............................... 22
!
WARNING! Long-term exposure to noise
can result in permanent hearing
impairment. So always use approved
hearing protection.
!
WARNING! Under no circumstances may
the design of the machine be modified
without the permission of the
manufacturer. Always use original
accessories. Non-authorized
modifications and/or accessories can
result in serious personal injury or the
death of the operator or others.
!
WARNING! A grass trimmer can be
dangerous if used incorrectly or
carelessly, and can cause serious or fatal
injury to the operator or others. It is
extremely important that you read and
understand the contents of this
operator’s manual.
S1156009-38,T26CS_1.fm Page 3 Wednesday, April 6, 2016 1:15 PM

4 – English
INTRODUCTION
Dear Customer,
Thank you for choosing a McCulloch product.You are thereby part of a story that started long ago, when the McCulloch
Corporation started its manufacturing of engines during World War II. In 1949, when McCulloch introduced its first light
one-man chainsaw, woodworking would never be the same again.
The line of innovative chainsaws would continue over the decades, and business was expanded, first by airplane and
kart engines in the 1950s, then by mini chainsaws in the 1960s. Later, in the 1970s and 80s, trimmers and blower vacs
were added to the range.
Today, as a part of the Husqvarna group, McCulloch continues the tradition of powerful engines, technical innovations,
and strong designs that have been our hallmarks for more than half a century. Lowering fuel consumption, emissions
and noise levels are of top priority to us, as is improving safety and user-friendliness.
We certainly hope that you will be satisfied with your McCulloch product, as it is designed to be your companion for a
long time. By following this operators manual’s advice on usage, service, and maintenance, its lifespan can be extended.
If you should need professional help with repair or service, please use the Service Locator at www.mcculloch.com.
McCulloch has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
This manual can also be downloaded at www.mcculloch.com.
S1156009-38,T26CS_1.fm Page 4 Wednesday, April 6, 2016 1:15 PM

English – 5
WHAT IS WHAT?
What is what on the grass trimmer?
5
6
14
15
8
7
10
1
11
12
13
9
1
3
2
4
16
1 Trimmer head
2 Cutting attachment guard
3 Shaft
4 Shaft coupling
5 Loop handle
6 Throttle trigger
7 Stop switch
8 Throttle lockout
9 Spark plug cap and spark plug
10 Starter handle
11 Fuel tank
12 Air filter cover
13 Primer bulb
14 Choke control
15 Operator ′ s manual
16 Locking pin
S1156009-38,T26CS_1.fm Page 5 Wednesday, April 6, 2016 1:15 PM

GENERAL SAFETY PRECAUTIONS
6 – English
Important Personal protective equipment
HELMET
Wear a protective helmet where there is a risk of falling
objects
HEARING PROTECTION
Wear hearing protection that provides adequate noise
reduction.
EYE PROTECTION
Always wear approved eye protection. If you use a visor
then you must also wear approved protective goggles.
Approved protective goggles must comply with the ANSI
Z87.1 standard in the USA or EN 166 in EU countries.
GLOVES
Gloves should be worn when necessary, e.g. when fitting
cutting attachments.
IMPORTANT!
The machine is only designed for trimming grass.
The only accessories you can operate with this engine
unit are the cutting attachments we recommend in the
chapter on Technical data.
Never use the machine if you are tired, if you have drunk
alcohol, or if you are taking medication that could affect
your vision, your judgement or your co-ordination.
Wear personal protective equipment. See instructions
under the ”Personal protective equipment” heading.
Never use a machine that has been modified in any way
from its original specification.
Never use a machine that is faulty. Carry out the safety
checks, maintenance and service instructions described
in this manual.Some maintenance and service measures
must be carried out by trained and qualified specialists.
See instructions under the Maintenance heading.
All covers, guards and handles must be fitted before
starting. Ensure that the spark plug cap and ignition lead
are undamaged to avoid the risk of electric shock.
The machine operator must ensure that no people or
animals come closer than 15 metres while working.When
several operators are working in the same area the safety
distance should be at least 15 metres.
Carry out an overall inspection of the machine before use.
See the maintenance schedule.
!
WARNING! This machine produces an
electromagnetic field during operation.
This field may under some
circumstances interfere with active or
passive medical implants.To reduce the
risk of serious or fatal injury, we
recommend persons with medical
implants to consult their physician and
the medical implant manufacturer before
operating this machine.
!
WARNING! Running an engine in a
confined or badly ventilated area can
result in death due to asphyxiation or
carbon monoxide poisoning.
!
WARNING! Never allow children to use or
be in the vicinity of the machine. As the
machine is equipped with a spring-loaded
stop switch and can be started by low
speed and force on the starter handle,
even small children under some
circumstances can produce the force
necessary to start the machine.This can
mean a risk of serious personal injury.
Therefore remove the spark plug cap
when the machine is not under close
supervision.
IMPORTANT!
A grass trimmer can be dangerous if used incorrectly or
carelessly, and can cause serious or fatal injury to the
operator or others. It is extremely important that you
read and understand the contents of this operator’s
manual.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen.
Ask your dealer for help in choosing the right equipment.
!
WARNING! Listen out for warning signals
or shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
S1156009-38,T26CS_1.fm Page 6 Wednesday, April 6, 2016 1:15 PM

GENERAL SAFETY PRECAUTIONS
English – 7
BOOTS
Wear sturdy, non-slip boots.
CLOTHING
Wear clothes made of a strong fabric and avoid loose
clothing that can catch on twigs and branches. Always
wear heavy, long pants. Do not wear jewellery, shorts
sandals or go barefoot.Secure hair so it is above shoulder
level.
FIRST AID KIT
Always have a first aid kit nearby.
Machine′s safety equipment
This section describes the machine′s safety equipment,
its purpose, and how checks and maintenance should be
carried out to ensure that it operates correctly. See the
”What is what?” section to locate where this equipment is
positioned on your machine.
The life span of the machine can be reduced and the risk
of accidents can increase if machine maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest service workshop.
Throttle lockout
The throttle lockout is designed to prevent accidental
operation of the throttle control. When you press the lock
(A) (i.e.when you grasp the handle) it releases the throttle
control (B). When you release the handle the throttle
control and the throttle lockout both move back to their
original positions. This movement is controlled by two
independent return springs.This arrangement means that
the throttle control is automatically locked at the idle
setting.
Make sure the throttle control is locked at the idle setting
when the throttle lockout is released.
Press the throttle lockout and make sure it returns to its
original position when you release it.
Check that the throttle trigger and throttle lockout move
freely and that the return springs work properly.
See instructions under the heading Start. Start the
machine and apply full throttle. Release the throttle and
check that the cutting attachment stops and remains at a
standstill. If the cutting attachment rotates with the throttle
in the idle position then the carburettor idle setting must
be checked. See instructions under the heading
Maintenance.
IMPORTANT!
All servicing and repair work on the machine requires
special training.This is especially true of the machine ′ s
safety equipment. If your machine fails any of the
checks described below you must contact your service
agent.When you buy any of our products we guarantee
the availability of professional repairs and service. If the
retailer who sells your machine is not a servicing dealer,
ask him for the address of your nearest service agent.
!
WARNING! Never use a machine with
faulty safety equipment.The machine's
safety equipment must be checked and
maintained as described in this section.
If your machine fails any of these checks
contact your service agent to get it
repaired.
A
B
S1156009-38,T26CS_1.fm Page 7 Wednesday, April 6, 2016 1:15 PM

GENERAL SAFETY PRECAUTIONS
8 – English
Stop switch
Use the stop switch to switch off the engine.
Start the engine and make sure the engine stops when
you move the stop switch to the stop setting.
Cutting attachment guard
This guard is intended to prevent loose objects from being
thrown towards the operator.The guard also protects the
operator from accidental contact with the cutting
attachment.
Check that the guard is undamaged and not cracked.
Replace the guard if it has been exposed to impact or is
cracked.
Always use the recommended guard for the cutting
attachment you are using. See chapter on Technical data.
Muffler
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user. A muffler
fitted with a catalytic converter is also designed to reduce
harmful exhaust gases.
In countries that have a warm and dry climate there is a
significant risk of fire.We therefore fit certain mufflers with
a spark arrestor mesh. Check whether the muffler on your
machine is fitted with this kind of mesh.
For mufflers it is very important that you follow the
instructions on checking, maintaining and servicing your
machine.
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to
the machine.
If the muffler on your machine is fitted with a spark
arrestor mesh this must be cleaned regularly. A blocked
mesh will cause the engine to overheat and may lead to
serious damage.
!
WARNING! Never use a cutting
attachment without an approved guard.
See the chapter on Technical data. If an
incorrect or faulty guard is fitted this can
cause serious personal injury.
!
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact
can result in burns to the skin.
Remember the risk of fire!
!
WARNING! The inside of the muffler
contain chemicals that may be
carcinogenic. Avoid contact with these
elements in the event of a damaged
muffler.
!
WARNING! Bear in mind that:
The exhaust fumes from the engine are
hot and may contain sparks which can
start a fire. Never start the machine
indoors or near combustible material!
S1156009-38,T26CS_1.fm Page 8 Wednesday, April 6, 2016 1:15 PM

GENERAL SAFETY PRECAUTIONS
English – 9
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
• Obtain maximum cutting performance.
• Extend the life of cutting equipment.
Trimmer head
• Only use the recommended trimmer heads and
trimmer cords. These have been tested by the
manufacturer to suit a particular engine size. This is
especially important when a fully automatic trimmer
head is used. Only use the recommended cutting
attachment. See the chapter on Technical data.
• Smaller machines generally require small trimmer
heads and vice versa.This is because when clearing
using a cord the engine must throw out the cord
radially from the trimmer head and overcome the
resistance of the grass being cleared.
• The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of
the same diameter.
• Make sure that the cutter on the trimmer guard is
intact.This is used to cut the cord to the correct length.
• To increase the life of the cord it can be soaked in
water for a couple of days before use. This will make
the cord tougher so that it lasts longer.
IMPORTANT!
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
Refer to the instructions for the cutting attachment to
check the correct way to load the cord and the correct
cord diameter.
!
WARNING! Always stop the engine
before doing any work on the cutting
attachment.This continues to rotate even
after the throttle has been released.
Ensure that the cutting attachment has
stopped completely and disconnect the
spark plug cap before you start to work
on it.
!
WARNING! A faulty cutting attachment
may increase the risk of accidents.
IMPORTANT!
Always ensure the trimmer cord is wound tightly and
evenly around the drum, otherwise the machine will
generate harmful vibration.
S1156009-38,T26CS_1.fm Page 9 Wednesday, April 6, 2016 1:15 PM

ASSEMBLY
10 – English
Fitting the loop handle
• Clip the loop handle onto the shaft. Note that the loop
handle must be fitted between the arrows on the shaft.
• Fit the bolt, securing plate and wing nut as shown in
the diagram. Tighten the wing nut.
Assembling and dismantling the
two-piece shaft
Assembly:
• Loosen the coupling by turning the knob.
• Align the tab of the attachment (A) with the hole in the
coupling (B).
• Push the attachment into the coupling until the
attachment snaps into place.
• Before using the unit, tighten the knob securely.
Dismantling:
• Loosen the coupling by turning the knob (at least 3
times).
• Push and hold the button (C). While securely holding
the engine end, pull the attachment straight out of the
coupling.
B
A
C
S1156009-38,T26CS_1.fm Page 10 Wednesday, April 6, 2016 1:15 PM