MD SPORTS SOC058_017B User manual

MODEL:SOC058_017B
VM Innovations
ASSEMBLY INSTRUCTIONS
TM
ATTENTION
Contact
MD Sports
Customer Service
DO NOT RETURN
TO THE STORE
* For additional resources and Frequently
Asked Questions, please visit us at
themdsports.com

www.themdsports.com
SOC058_017B 1
(Continued on the next page.)
NOTICE!
This product is covered by a limited warranty that is effective for 90 days from the date of purchase. If, during the limited warranty
period, a part is found to be defective or breaks, we will offer replacement parts at no cost to you, the customer. The only exceptions
to the warranty include mainframes, table tops, playing surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper usage, alteration, misuse, abuse, accidental damage or
neglect.
This Limited Warranty gives you specific legal rights and you may also have other rights which vary from one State (province) to
another.
A PURCHASE RECEIPT (or other proof of purchase) will be required before any warranty service is initiated. For all
requests for warranty service, please feel free to contact our
Consumer Service Department at:
WEBSITE: www.themdsports.com
Please be aware of your product’s Limited Warranty for the return/refund policy from the store, We, at Medal Sports, can not handle
the product which is out of product’s limited warranty since we only provide available parts. Thank you!
PLEASE CONTACT US BEFORE RETURNING
THE PRODUCT TO THE STORE.
LIMITED 90 DAYS WARRANTY
STAPLE YOUR RECEIPT HERE
1 - Please leave your name, address, phone number, model number, parts needed on the answering machine if there is no attendant.
Failure to do so will result in a delay in shipping parts to you.
2 - Please review the replacement parts list and make sure that you have all of your parts before beginning assembly.
For questions that may arise or for missing/damaged parts, please contact us.
3 - Since you build all tables upside down, please inspect tabletops or playing surfaces right away before putting together, all damaged
table tops/playing surfaces need to be returned to the store. Please contact with retailer for their return policy.

www.themdsports.com
SOC058_017B 2
(Continued on the next page.)
Phillips Screwdriver - Not Included
Standard (Flat Head Screwdriver) - Not Included
Allen Key - Included
CAUTION!
Electric Screwdrivers may be helpful during assembly; however, please set a low torque and use
extreme caution.
1 - This product is intended for INDOOR use only.
2 - Please do not sit, climb or lean on the product.
3 - Please do not drag the product when moving it in order to avoid damaging the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces of the product.
5 - This is not a child's toy, adult supervision is required for children playing this game.
Power Tools
- Set Low Torque
High Torque
over tightened
WARNING:
Adult Assembly Required.
WARNING:
CHOKING HAZARD 
TOOLS REQUIRED
ASSEMBLY TIPS
IMPORTANT NOTICE!
Strong Adults Needed No Children in
Assembly Area Keep away from pets
Do not use or keep product
outdoors. For indoor use only.
No wet/humid conditions.
X2
1 - Please read the instructions carefully, and follow all assembly, operation and safety instructions properly in order to avoid
damage or injury. For the assembly, at least two adults are required.
2 - Some figures or drawings may not look exactly like your product. Please read and understand the text before beginning each
assembly step.

SOC058_017B PARTS LIST
910 11 12
13 14 15 16
2 3 41
x2 x2 x1 x2
6 7 85
x2 x4 x2
x2 x2 x2 x2
x11 x11 x2 x4
x2
18 19 20
x16 x16 x2
21
x4
22
x8
23
x8
24
x4
25
x24
26
x16
27
x8
28
x36
29
x26
30
x26
17
x2
31
x10
32
x8
Side Apron
Left Leg
Inside Ball Cup Goal Box Ball Catcher Ball Return
Channel
Support Brace Leg Leveler Outside Ball Cup
End Apron Playfield Right Leg
Player - Red
Player - Blue 5-Hole Rod
2-Hole Rod Rod Washer
Scorer Holder Rod End Cap Handle
“L” Bracket
3.5x38mm Screw M6x15mm Bolt
4x32mm
Flat Head Screw
4x15mm ScrewM6x35mm Bolt
T4x25mm Bolt T5x15mm Bolt4mm Nut
Rod Bumper Slide Scorer
3-Hole Rod
www.themdsports.com
SOC058_017B 3
(Continued on the next page.)
FOR FIG. 2
FOR FIG. 4 FOR FIG. 5 FOR FIG. 5 FOR FIG. 7
FOR FIG. 7 FOR FIG. 6
FOR FIG. 8 FOR FIG. 8
FOR FIG. 6
FOR FIG. 8
FOR FIG. 6
FOR FIG. 8
FOR FIG. 8 FOR FIG. 8
FOR FIG. 9 FOR FIG. 9
FOR FIG. 8
FOR FIG. 9
FOR FIG. 9
FOR FIG. 4
FOR FIG. 5, 6
FOR FIG. 2, 3 FOR FIG. 4
FOR FIG. 4
FOR FIG. 8 FOR FIG. 8 FOR FIG. 1,9 FOR FIG. 9
FOR FIG. 1 FOR FIG. 3 FOR FIG. 4

SOC058_017B PARTS LIST
SOC058_017B PRE-INSTALLED PARTS
P1 P2
x4 x16 x2
P3
x2
P4
P5 P6
x8
Rod Bushing Ball Return Cover Goal Cover
M6 Nut
x4
Square Nut with
Screws
Top corner
33
x14
34
x2
35 36
x1
4x12mm Screw
37
x4
Plastic “L” Bracket
Soccer Ball Allen Key
38
x2
39
x4
Top Slat Board 4 x 25mm Round
Head Screw
40
x6
41
x4
Triangle Board
Cap
Triangle Board
x4
Stop Ring
x24
M6 Spring
Lock Washer
42
M6 Washer
x8
42 43
x2
44
Goal End Board
www.themdsports.com
SOC058_017B 4
(Continued on the next page.)
FOR FIG. 7
FOR FIG. 7 FOR FIG. 1 FOR FIG. 1 FOR FIG. 5
FOR FIG. 7 FOR FIG. 1 FOR FIG. 4 FOR FIG. 4
FOR FIG. 8
FOR FIG. 9 FOR FIG. 8
FOR FIG. 2 FOR FIG. 4
FOR FIG. 2 FOR FIG. 1
ASSEMBLY INSTRUCTIONS:
1. Find a clean, level place to begin the assembly of your Product.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts list pages.
Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work surface.

www.themdsports.com
SOC058_017B 5
(Continued on the next page.)
X 2
X 2
X 4
2
38
X 6
31
39
X 2
44
X 2
P4
FIG. 1C
2
38
39
P4
FIG. 1
FIG. 1B
31
31
31
FIG. 1A 44
2
44
2

www.themdsports.com
SOC058_017B 6
(Continued on the next page.)
X 2
X 2
X 8
1
X 8
25
P3
P5
1
2
3
25
FIG. 2 Assembly
X 1
3
X 16
25
FIG. 3
FIG. 2
25
1
1
2
P3
P5
FIG. 1 Assembly
FIG. 1 Assembly
Note: Do not tighten the screws
at this step.

www.themdsports.com
SOC058_017B 7
(Continued on the next page.)
4
4
4
5
5
26 42
43
P6
FIG. 3 Assembly
X 16
X 2
X 8
X 4
X 2
X 8
X 1
X 24
4
5
24
26
27
36
42
X 4
43
P6
FIG. 4 FIG. 4A
FIG. 3 Assembly
26
24
24
4
4
4
5
5
27
42
FIG. 4B

FIG. 4 Assembly
X 2
X 24
X 6
X 4
www.themdsports.com
SOC058_017B 8
(Continued on the next page.)
6
7
7
28
28
40
6
28
28
28
40
40
40
FIG. 5
FIG. 5A
FIG. 5B
6
28 28

www.themdsports.com
SOC058_017B 9
(Continued on the next page.)
X 12
X 2
X 2
X 2
10
10
11
11
12
12
28
28
28
FIG. 6
FIG. 5 Assembly
Note: Lift the table assembly from the floor with two
strong adults, turn it over, and set table on its legs in
the location where you play. Go back and make sure
that all connections are tight.
DO NOT LEAN THE
TABLE ON ITS LEGS
HOLD TABLE
CABINET DO NOT HOLD THE LEGS
CAUTION: Two strong adults are recommended to turn the table over as shown.
1. Lift the table off the ground.
2. Turn the table over.
3. Place it on all four feet at the same time on the ground.

outside
inside
www.themdsports.com
SOC058_017B 10
(Continued on the next page.)
98
33
33
33
37
FIG. 7A
X 4
X 4
X 2
X 14
X 2
8
9
33
37
41
FIG. 7
37
41
FIG. 7C
FIG. 7B
Note: Cover the screw by inserting triangle
board cap (#41) into the Triangle Board (#37).

Handle hole
www.themdsports.com
SOC058_017B 11
(Continued on the next page.)
FIG. 8 FIG. 8A
= Blue
= Red
ORDER OF PLAYERS
(Overhead View)
16
16
17
16
16
15
15
17
29
30
P2
16
19
19
3035
29
X 4
X 2
X 11
X 2
X 11
X 26
X 4
X 16
X 26
X 16
13
14
15
16
17
18
19
29
30
35
X 16
P2
Note: Players of the same team color should have Handles
on the same side, and each team’s players should be facing
their opponent.
17 or13 14
18
19
18
19
or
13 14
FIG. 8B
18
18
FIG. 8C

20
21
22
31
X 8
X 2
X 4
X 8
X 4
X 4
X 8
20
21
22
23
31
32
P1
P1
FIG. 9
15
16
23
32
Handle hole
FIG. 9B
FIG. 9A
Note: The goalie should be at the
left side of each player.
www.themdsports.com
SOC058_017B 12
(The last page)
YOU ARE NOW READY TO PLAY!
Note: The Rods have a hole at the
end where their Handles will go.