Mediasite ML931 User manual

12V 7A12V 7A
ML931 / ML941 SET-UP GUIDE
SETTING UP YOUR MEDIASITE ML MULTIVIEW RECORDER
1. CONNECT VIDEO SOURCE(S)
ML931
A. Connect a 3G/HD/SD-SDI video source to an open SDI port.
B. Connect an SD video source to the S-Video/Composite port.
ML941
C. Connect an HDMI video source to the HDMI port.
D. Connect a 3G/HD/SD-SDI video source to the SDI port.
E. Connect an SD video source to the S-Video/Composite port.
2. CONNECT A CONTENT (SLIDE) SOURCE
Connect the appropriate adapter to the HDMI/DVI/RGB/YPbPr port. Then connect
your laptop, white board, document camera or any content source to the adapter.
3. CONNECT THE AUDIO SOURCE
Connect the breakout cable to the Recorder. Then connect an audio source to the
appropriate connector on the breakout cable. If you are using embedded SDI or HDMI
audio, no additional audio source is required.
4. TURN ON SOURCES
5. CONNECT THE RECORDER TO THE NETWORK
6. CONNECT THE POWER CABLE
Connect the power cable to the Recorder and then plug into a power source.
7. POWER ON THE RECORDER
The power button is located on the left side of your ML Recorder (not shown).
ADDITIONAL FEATURES
On the back of your ML Recorder is an embedded handle, an adjustable kickstand for desktop
placement and a Kensington Security Slot.
[e-mail] | 608.443.1600 | #videodoneright
A.
ML931 ML941 BREAKOUT
CABLE
3.
6.6.
5.5.
2.2.
C.
E.B.
3.3.
RCA
(UNBALANCED)
XLR
(BALANCED)
D.

©2017 Sonic Foundry, Inc. All rights reserved. Sonic Foundry, the Sonic Foundry logo, Mediasite and the Mediasite logo are registered trademarks of Sonic Foundry, Inc. All other trademarks are the property of their respective owners. ML931 / ML941 05/2017
CONFIGURING YOUR ML931 / ML941
[e-mail] | 608.443.1600 | #videodoneright
ML931 / ML941 QUICK REFERENCE
ML931 ML941
DVI-I INPUTS
HDMI, DVI-D, RGB (VGA),
YPbPr (Component)
1 1
S-VIDEO/COMPOSITE
INPUTS
S-Video/Composite 1 1
3G/HD/SD-SDI INPUTS
3G/HD/SD-SDI 2 1
HDMI INPUTS
HDMI 0 1
AUDIO INPUTS
HDMI (Embedded) 1 2
RCA (Unbalanced) 1 1
XLR (Balanced) 1 1
SDI (Embedded) 2 1
INCLUDED EQUIPMENT
HDMI to DVI-I adapter 1 1
RGB (VGA) to DVI-I
adapter
1 1
YPbPr (Component)
to DVI adapter
1 1
Composite to S-Video
adapter
1 1
Audio breakout cable
(XLR and RCA)
1 1
Power cable 1 1
DC power adapter 1 1
POWER REQUIREMENTS
Power 84W 84W
Input frequency 50-60Hz 50-60Hz
AC voltage input 100-240V 100-240V
Max heat dissipation 326 BTU/h 326 BTU/h
1. CONNECT THE RECORDER TO MEDIASITE
Open the Recorder Interface on your ML Recorder
and go to the Settings page. Click Mediasite
Connections. Enter your Mediasite’s Service URL and
the credentials you need to connect to it. You will get
this information from your Mediasite administrator.
2. LICENSE THE RECORDER
Click Unlicensed in the upper-right corner to acquire a
license from the connected Mediasite Video Platform.
Restart the Recorder when prompted.
LICENSING REQUIRED
You cannot record presentations with an unlicensed Recorder.
3. VERIFY YOU HAVE THE LATEST RECORDER
SOFTWARE
When your Recorder restarts after licensing, it
automatically checks for software updates on the
connected Mediasite Video Platform and Sonic
Foundry’s Customer Assurance Portal. Return to the
Settings page, click System, enter the default Recorder
administrator credentials (Admin/mediasite), and
go to Software Update to see if any updates are
available:
UPDATES AVAILABLE ON MEDIASITE
Click Apply Updates to install the latest updates. The Recorder
reboots once all updates have been applied.
UPDATES AVAILABLE ON CUSTOMER ASSURANCE PORTAL
If newer software updates are available on the Customer
Assurance Portal, you will see a download link. Click the link and
enter your organization’s credentials to download the software
to a location accessible from the Recorder. You will then upload
the software and update the Recorder. The Recorder reboots
once all updates have been successfully applied.
If you do not know your organization’s Customer Assurance
Portal credentials, contact your Mediasite administrator.
4. SELECT YOUR SOURCES
On the Input Devices page, select the
appropriate video and audio inputs.
5. PREVIEW INPUTS
Go to the Recorder page to preview
your inputs. Monitor incoming audio
levels and adjust them using the audio
level fader (analog only). Monitor the
incoming video and content sources
and adjust your equipment settings to
get the desired effect.
6. START RECORDING
Once you are satisfied with the inputs,
you can begin recording. It is always
a good idea to record and review
a test presentation. For additional
information:
RECORDER HELP
Click Help when logged into the Recorder for
information on managing your Recorder and
recorded content.
CUSTOMER ASSURANCE PORTAL
Go to the Customer Assurance Portal at
www.sonicfoundry.com/support to download
the Mediasite Recorder Guide, which contains
additional information on managing your
Recorder and recorded content. Contact
your Mediasite administrator for your
organization’s credentials.