Medion LIFE P18047 User manual

125.7cm/50“ LCD-LED-Backlight-TV
MEDION® LIFE®P18047 (MD 30912)
Instruction Manual
30912 EN eCom RC Cover.indd Alle Seiten30912 EN eCom RC Cover.indd Alle Seiten 20.03.2015 14:01:1620.03.2015 14:01:16

EN
1
Table of contents
1. About these Instructions......................................................................................................... 3
1.1. Warning Symbols and Keywords.......................................................................................................................................................3
1.2. Proper use..................................................................................................................................................................................................3
1.3. Full HD.........................................................................................................................................................................................................4
1.4. Contents.....................................................................................................................................................................................................4
2. Safety Instructions .................................................................................................................. 5
2.1. Operating Safety .....................................................................................................................................................................................5
2.2. Set-Up Location.......................................................................................................................................................................................5
2.3. Repairs.........................................................................................................................................................................................................6
2.4. Intended Environment..........................................................................................................................................................................6
2.5. Safety when connecting.......................................................................................................................................................................6
2.6. Power Supply............................................................................................................................................................................................6
2.7. Battery Handling .....................................................................................................................................................................................7
2.8. Information about Conformity...........................................................................................................................................................8
3. Device Overview...................................................................................................................... 9
3.1. Front.............................................................................................................................................................................................................9
3.2. Rear and right-hand side................................................................................................................................................................... 10
3.3. Remote Control..................................................................................................................................................................................... 11
4. Start of Operation................................................................................................................. 13
4.1. Unpacking .............................................................................................................................................................................................. 13
4.2. Installation.............................................................................................................................................................................................. 13
4.3. Inserting Batteries into the Remote Control ............................................................................................................................. 13
4.4. Connecting the antenna ................................................................................................................................................................... 14
4.5. Connecting power supply ................................................................................................................................................................ 14
4.6. Switching the LCD TV on and off.................................................................................................................................................... 14
4.7. Channel search when switching on for the first time............................................................................................................. 15
5. Operation ............................................................................................................................. 16
5.1. Channel selection ................................................................................................................................................................................ 16
5.2. Sound settings ...................................................................................................................................................................................... 16
5.3. Screen settings...................................................................................................................................................................................... 16
5.4. Displaying information ...................................................................................................................................................................... 17
5.5. Displaying Information ...................................................................................................................................................................... 17
5.6. Opening the favourites list............................................................................................................................................................... 17
5.7. Selecting the source ........................................................................................................................................................................... 17
6. Teletext................................................................................................................................. 18
6.1. Using teletext ........................................................................................................................................................................................ 18
7. Connecting devices ............................................................................................................... 19
7.1. Connecting headphones .................................................................................................................................................................. 19
7.2. Digital amplifier via coaxial connection ..................................................................................................................................... 19
7.3. Connecting a soundbar/surround sound system .................................................................................................................... 19
7.4. Connecting a DVD/Blu-ray player.................................................................................................................................................. 19
7.5. Connecting a video recorder........................................................................................................................................................... 20
7.6. Connecting a DVD recorder ............................................................................................................................................................. 20
7.7. Connecting a receiver (SAT, DVB-T, decoder, etc.) .................................................................................................................... 20
7.8. Connecting a DVD/video recorder and SAT receiver .............................................................................................................. 21
7.9. Connecting a camcorder................................................................................................................................................................... 21
7.10. Device with HDMI or DVI output.................................................................................................................................................... 21
7.11. Connecting a PC................................................................................................................................................................................... 22
7.12. Connecting a network........................................................................................................................................................................22
8. Via the OSD menu ................................................................................................................. 23
8.1. Navigating in the menu..................................................................................................................................................................... 23
8.2. The menu system in detail................................................................................................................................................................ 24
9. PVR function......................................................................................................................... 41
9.1. Start/stop recording directly............................................................................................................................................................ 42
9.2. Programming recording.................................................................................................................................................................... 42
9.3. Playing back recordings..................................................................................................................................................................... 42
10. EPG – Programme guide....................................................................................................... 42
11. Media portal ......................................................................................................................... 43
11.1. Media library.......................................................................................................................................................................................... 43
12. HbbTV system ....................................................................................................................... 44

2
13. Internet ................................................................................................................................ 44
14. MEDION® Life Remote App ....................................................................................................45
15. Data protection MEDION® Smart TV...................................................................................... 45
16. Troubleshooting ................................................................................................................... 46
16.1. Do You Need More Help? ..................................................................................................................................................................47
17. LED-Backlight TV pixel faults................................................................................................ 47
18. Cleaning................................................................................................................................48
19. Disposal ................................................................................................................................ 48
20. Technical Data ...................................................................................................................... 49
20.1. Product data sheet .............................................................................................................................................................................. 51
21. Legal Notice .......................................................................................................................... 52
22. Index..................................................................................................................................... 53

EN
3
1. About these Instructions
Before using the device for the first time, you should read these operating instructions thoroughly and follow
the safety advice. This device may only be used as described in the operating instructions.
Always keep these operating instructions at hand but store them safely so that you can pass them on to a new
owner should you sell the unit.
1.1. Warning Symbols and Keywords
DANGER!
Warning of immediate risk of fatal injury!
WARNING!
Warning: possible mortal danger and/or serious irreversible injuries!
CAUTION!
Warning: possible light or moderate injuries!
CAUTION!
Please follow the guidelines to avoid property damage.
PLEASE NOTE!
Additional information on using the device!
PLEASE NOTE!
Please follow the guidelines in the operating instructions.
WARNING!
Warning: danger of electric shock!
WARNING!
Warning: danger due to excessive volume!
• Bullet point/information on operating steps and results
Tasks to be performed
1.2. Proper use
• This device is used to receive and play back TV programmes. Thanks to its various connection options, it can also be
used to receive and play back media from various external sources (receiver, DVD player, DVD recorder, video record-
er, PC, etc.). Your device offers a number of options for usage.
• The device is intended for private use only and not for industrial/commercial use.
• Please note that we shall not be liable for damage caused by improper use.
• Do not modify the device without our consent and do not use any auxiliary equipment which we have not ap-
proved or supplied.
• Use only spare parts and accessories which we have supplied or approved.
• Heed all the information in these operating instructions, especially the safety information. Any other use is deemed
improper and can cause personal injury or damage to the device.
• Do not use the device in extreme environmental conditions.
• This product is intended for use in dry, indoor areas only.
• This device is not suitable as a data monitor for office workplaces.

4
1.3. Full HD
Your LED-Backlight TV is equipped with the feature “Full HD”. This means that it is capable of displaying
high-resolution television programmes (HDTV). The prerequisite for this is a HDTV signal.
1.4. Contents
Please check the items received in the box and inform us within 7 days from purchase if anything is missing. Your statu-
tory rights are not affected.
WARNING!
Keep packaging material such as plastic film away from children. There is a risk of
suffocation if used improperly.
You should receive the following items
• LED backlight TV
• Remote control (RC1208) incl. 2 x 1.5V batteries (type LRO3/AAA)
• AV adapter
• YUV adaptor
• Wi-Fi dongle (Wistron, Vezzy 200, MSN 4004 4275)
• USB extension cable
• Stand incl. fastening screws
• Documentation

EN
5
2. Safety Instructions
2.1. Operating Safety
• Children should be supervised to ensure they do not play with this unit. This unit is not
intended for use by people (including children) with reduced physical, sensory or mental
abilities or for those without experience and/or knowledge, unless they are supervised by
a person responsible for their safety or they have been instructed on its use.
WARNING!
Keep packaging material such as plastic film away from children. There is a risk of
suffocation if used improperly.
WARNING!
Never open the housing of the LED-Backlight TV (electrical shock, short circuit and
fire hazard)!
WARNING!
Never insert any objects through the slots and openings of the LED-Backlight TV
(electrical shock, short circuit and fire hazard)!
• The slots and openings on the LED-Backlight TV are for ventilation purposes. Do not cov-
er these openings (overheating, fire risk)!
• Do not put any pressure on the display. There is a risk that the screen may break.
• The remote control has a class 1M infrared diode. Never use optical devices to look at the
LED.
CAUTION!
There is a risk of injury if the screen is damaged! Recover all broken pieces using
protective gloves and send them to your Service Centre for proper waste disposal.
Then wash your hands with soap because chemicals may have leaked out.
• To avoid damaging the screen do not touch it with fingers or sharp objects.
• Contact customer services if:
−the power cable is burnt or damaged
−liquid has penetrated the device
−the device is not operating correctly
−the device has fallen, or the casing is damaged
2.2. Set-Up Location
• In the first hours of operation, new devices may emit a typical, unavoidable but com-
pletely harmless smell, which will decline increasingly in the course of time. We recom-
mend that you ventilate the room regularly, in order to counteract the formation of the
smell.
• Keep your LED-Backlight TV and all connected devices away from moisture and avoid
dust, heat and direct sunlight.
• Do not use the device outdoors because other effects such as rain, snow etc. can also
damage the device.
• The device must not be exposed to water droplets or spray. Do not place objects that are
filled with water (such as vases) on the device. The container may tip over and the liquid
will impair the electrical safety.
CAUTION!
Keep candles and all other types of open flames away from the product to prevent
the spread of fire.

6
• Make sure that there is enough clearance in the wall units! Ensure a minimum separation
of 10 cm around the device for sufficient ventilation.
• Operate all components on a stable, level and vibration-free base, to prevent the
LED-Backlight TV from falling over.
• Avoid dazzle, reflections and strong bright-dark contrast in order to protect your eyes.
• The optimal viewing distance is 3 times the screen diagonal.
2.3. Repairs
• Repairs to your LED-Backlight TV should only be carried out by qualified specialists.
• Please contact our authorised service centre if you have any problems with your
LED-Backlight TV.
• Make sure to use only replacement parts provided by the manufacturer. The device may
sustain damage if unsuitable replacement parts are used.
2.4. Intended Environment
• The device can be operated at an ambient temperature of +5° C to +35° C and a relative
humidity of 20% - 85% (non condensing).
• In the switched-off state the LED-Backlight TV can be stored from -20° C to +60° C.
• Keep the device at a distance of at least one metre from high frequencies and magnetic
sources of interference (television, loudspeaker boxes, mobile telephones etc.) to avoid
malfunctioning.
WARNING!
After transporting the LED-Backlight TV wait until the device has reached ambi-
ent temperature before switching it on.
Large changes in temperature or fluctuations in humidity can cause moisture to
build up due to condensation within the LED-Backlight TV, which can cause an
electrical short circuit.
• During thunderstorms or if the device is not going to be used for long periods, remove
the plug from the mains socket and the aerial cable from the aerial socket.
2.5. Safety when connecting
2.6. Power Supply
• Even when switched off, some components of the device are live. In order to disconnect
the power to your LED-Backlight TV or to completely isolate the device from voltage
sources remove the mains plug from the mains socket.
WARNING!
Do not open the device’s housing. There is a risk of electric shock when the hous-
ing is open. The device does not contain any parts requiring maintenance.
• Only plug the LED-Backlight TV into an earthed socket with 220-240 V~ 50 Hz. Contact
you electricity provider if you are not sure if the socket is earthed or not.
• The socket must be near the LED-Backlight TV and easily accessible.
• In order to disconnect the power to your LED-Backlight TV or to completely isolate the
device from voltage sources remove the mains plug from the mains socket.
• For extra safety, we recommend using an over-voltage protection device to prevent your
LED-Backlight TV sustaining damage as a result of power surges or lightning strikes.
• If you are using an extension cable, make sure that it complies with UK Electrical Safety
requirements. If in doubt, contact your electrician.

EN
7
• Position the cable so that nobody is able to step on it or trip over it.
• Do not place any objects on the cable to avoid damaging it.
2.7. Battery Handling
WARNING!
Batteries can contain combustible materials. If not handled correctly batteries can
leak, become very hot, ignite or even explode, which could damage your device
or/and your health.
Please ensure compliance with the following advice:
• Keep batteries away from children. Contact your doctor immediately if a battery is swal-
lowed.
• Never charge batteries (unless it is clearly indicated).
• Never discharge batteries by high power output.
• Never short-circuit the batteries.
• Never expose the batteries to excessive heat such as sunshine, fire or similar.
• Do take apart or deform the batteries. Your hands or fingers could get injured or battery
fluids could get into your eyes or onto your skin. If this should happen then rinse the af-
fected areas immediately with a large amount of clean water and contact your doctor im-
mediately.
• Avoid heavy impacts and vibrations.
• Always observe the correct polarity.
• Make sure that the plus (+) and minus (-) poles are correctly inserted in order to avoid
short circuits.
• Never mix new and old batteries or different types of batteries. This could cause your de-
vice to malfunction. In addition, the weaker batteries would discharge too much.
• Immediately remove used batteries from the device.
• Remove the batteries from the device if you do not intend to use it for a long period of
time.
• Replace all the old batteries in a device with new batteries of the same type.
• Isolate the contacts of the batteries with sticky tape if you want to store or dispose of
them.
• Clean the contacts on the battery and device before inserting.

8
2.8. Information about Conformity
The device fulfils electromagnetic compatibility and electricity safety requirements.
The device complies with the fundamental requirements and the relevant regulations of
EMC Directive 2004/108/EC, the Low Voltage Directive 2006/95/EC and Directive 2011/65/
EU (RoHS).
This device fulfils the basic requirements and the relevant regulation of the Ecodesign
Guideline 2009/125/EG (Commission Regulation 642/2009).
Your device complies with the fundamental requirements and the relevant regulations of
R&TTE Directive 1999/5/EC.
Due to the 5GHz frequency range of the supplied wireless LAN solution, the device may
only be used inside buildings in the EU.

EN
9
3. Device Overview
3.1. Front
1
2
3
OFF/ON
1) LCD screen
2) Mains switch
3) Infrared sensor: Reception field for the infrared signals from the remote control
Operating light: Lights up blue when the appliance is in standby mode.

10
3.2. Rear and right-hand side
1
2
5
2
3
4
+
P/CH
+
TV/AV
12
13
14
15
YPbPr SIDE AV
5Vdc
Max.500mA
5Vdc
Max.500mA
MENU
6
7
8
9
10
11
SPDIF
Coax. OUT
SCART
SPDIF
Coax.OUT
SCART
16
1) COMMON INTERFACE (CI+): Card slot for connecting CI modules
2) USB (5V , 500 mA max.): USB connection for media playback and recording (PVR)
3) SIDE AV: Audio/video input (via included cinch adapter)
4) For connecting headphones with a 3.5 mm jack plug
5) Y Pb Pr: Component inputs for connecting devices with component output
(via included cinch adapter)
6) HDMI 1-3: HDMI connection for devices with HDMI output
7) ANT.: Aerial connection (DVB-T/DVB-T2/DVB-C/analogue)
8) VGA: Connection for connecting a PC
9) SCART: SCART connection(input/output)
10) SPDIF Coax. OUT: Digital audio output (coaxial)
11) LAN: Network connection to connect to the Internet
12) : Set the volume or navigate in the menu
MENU (press both buttons at the same time): Call up the on-screen menu,
to make settings on the device.
13) P/CH +/- : Select a channel or navigate in the menu
14) TV/AV: Select source
15) Standby button: switches the device on or into standby mode
16) Fixing holes for a wall bracket (hole spacing 400 x 400 mm).
PLEASE NOTE!
When mounting the device, make sure that you use M6 screws. The length of the screws corresponds to the
thickness of the wall bracket plus a max. of 13 mm.

EN
11
3.3. Remote Control
27
26
25
20
19
18
16
15
14
17
21
22
23
24
28
13
12
11
8
9
10
7
6
5
4
3
2
1
1) LED display for confirming button selection
2) 2 :Switching between DVB-T and DVB-C programmes/multifunction button for programme position or in-
put source
3) : Switch LCD TV on/off (standby mode on/off )
4) GZKV: Exit menu
5) NCPI: Analogue TV: stereo/mono;
Digital TV: select audio language (if available)
6) UK\G: Select screen format
7) UNGGR: Activate/deactivate sleep timer
8) HCX: Activate favourites list
9) GRI: Digital TV: call up electronic programme guide
10) UQWTEG: Select input signal of connected devices
11) : Increase (+) or decrease (−) volume.
12) Numeric keys:
TV: programme selection, teletext: page selector
13) : Set previous TV channel

12
14) : Activate teletext
Press 2x = set transparent
Press 3x = close
15) Direction button : Up in menu
Digital TV: select the info bar of the current channel, teletext: select next page;
Direction button : Down in menu,
Digital TV: select the info bar of the current channel, teletext: select previous page;
Direction button : Left in menu
teletext: call up sub-page;
Direction button : right in menu
teletext: call up sub-page
16) QM: Confirm selection in certain menus
17) R"/1-: Programme selection buttons
TV: select next (+) / previous (−) channel;
teletext: select next (+) / previous (−) page
18) TGVWTP: Go back one level in menus
19) OGPW: Open and close menu
20) RTGUGV: Select picture mode
21) KPHQ: Digital TV: display info (e.g. current channel number)
22) : Internet button
23) : Subtitles on/off (if available)
24) TGF"DWVVQP1\QQO: For teletext or menus
ITGGP"DWVVQP1TGRGCV: For teletext or menus
[GNNQY"DWVVQP1TQQV: For teletext or menus
DNWG"DWVVQP1VKVNG: For teletext or menus
25) Media button
: Fast rewind;
: Fast forward;
: Start recording (PVR);
: Stop playback;
: Start playback;
: Pause playback;
: No function;
: No function
26) OGFKC: Call up media browser
27) : Mute
28) "1/ FKURNC[1: Multi-function button for channel or input source / YouTube function
1Changing the button functions 1 & 2:
The 1 & 2 buttons can be programmed as required (channel or input source).
Start by selecting the function you require and then hold down the corresponding button for 5 seconds until
“MY BUTTON IS SET”appears. This confirms the new programming.
PLEASE NOTE!
After each “FIRST TIME INSTALLATION” your customised button programming is deleted and reset to the fac-
tory defaults.

EN
13
4. Start of Operation
CAUTION!
Before starting up please make sure that you read the “Safety instructions”section
4.1. Unpacking
• Select a suitable place for setting up the device.
• Open the box very carefully to avoid damaging the device. The device could be damaged if you use a knife with a
long blade to open the box.
• The box contains a number of small items (including batteries). Keep these items out of reach of children; the parts
are easy to swallow.
• Store the packaging material in a safe place; only use this box to transport the TV.
WARNING!
Keep packaging material such as plastic film away from children. There is a risk of
suffocation if used improperly.
4.2. Installation
Attach the base stand as shown in the drawing. Carry out this step before connecting the LED-Backlight TV.
4x
SPDIF
Coax.OUT
SCART
SPDIF
Coax.OUT
SCART
4x
4.3. Inserting Batteries into the Remote Control
Open the battery compartment cover on the back of the remote control.
Insert two LR03 (AAA) 1.5-V batteries in the battery compartment of the remote control. Check the battery polarity
(inscribed on the bottom of the battery compartment).
Replace the cover.
CAUTION!
Remove the batteries if the device will not be used for long periods. The remote control can be
damaged by leaking batteries.

14
4.4. Connecting the antenna
Your LCD TV supports different antenna signals.
You can feed the following image signals via the connection labelled ANT.:
• via analogue cable / an analogue home aerial
• via a DVB-T2antenna or
• via a DVB-C2connector (digital cable)
Connect the antenna cable from either the house aerial/the analogue cable connection, the DVB-T antenna or the
DVB-C connection to the antenna connection on the LCD television.
NOTE!
To receive encrypted/subscription channels you will need to use a CAM module and an appropriate card. In-
sert the CAM module (available from dealers) in the appropriate slot on the left side of the device (Common
Interface). You can then insert the card from your provider into the CAM module.
4.5. Connecting power supply
Plug the device into an easily accessible 220–240V ~ 50Hz mains socket.
4.6. Switching the LCD TV on and o
Set the power switch on the lower right-hand side of the device to QP. The device switches to standby mode and
the display on the front will light up.
To switch the device on, press
- on the remote control: the Standby/On button , one of the number buttons or one of the R/1- buttons;
- on the device: the UVCPFD[ button.
Use the Standby/On button on the remote control to switch the device back into standby mode. The device will
be switched off but continues to use power.
NOTE!
If there is no input signal, the device automatically switches to standby mode after five minutes. A count-
down timer will be shown on the screen until this occurs. This function is not available with all sources.
2This service must be available in your region

EN
15
4.7. Channel search when switching on for the rst time
You will be guided through the first time installation when you switch the device on for the first time.
Using the direction buttons  you can move up or
down in the menu and select the required language.
After confirming the selected language with QM the
first time installation will begin.
Use  to select the desired country. The country
setting will influence the order in which the channels
are stored. Also, there are a number of options preset
for the individual countries.
If you would also like to change the default settings
for the teletext language, use the direction button 
to select the entry TELETEXT SPRACHE then
use the direction buttons  to select the desired
language region  WEST, EAST, CYRIL-
LIC, TURK/GRE or ARABIC.
If Siyou would also like to search for encrypted chan-
nels, set the option to YES.
Then press QM to continue. A query about the digi-
tal antenna signal will appear.
Now you are asked to carry out the network settings. Select NO, if you want to skip this step. If you select YES, the
network options appear:
Here you can select the network type WIRELESS DEVICE or WIRED DEVICE.
If you are using USB Wi-Fi dongles, choose the option WIRELESS DEVICE as your network type and confirm
with QM. The television will scan for available wireless networks. Select the desired network. If this is secured, you
must enter the network password. See also the documentation that came with your wireless router.
If you have selected the setting WIRED DEVICE, a dynamic connection is automatically created as soon as you
connect the LCD TV to the Internet.
You can also enter a static IP address. To do this, press the green button to access the ADVANCED menu. Here you
can use the number buttons to enter the required IP address to connect your TV to the Internet. Using the red but-
ton, you switch between DYNAMIC and STATIC
Here you specify whether the digital antenna signal is to be fed in via AERIAL
(DVB-T) or CABLE (DVB-C). The search for digital TV channels will take place
according to this setting.
To stop the search at any time, press the OGPW button.
Search type setting: Antenna
To start the digital channel search, use the direction buttons  to select
YES and then press QM. To cancel, use the direction buttons  to select
NO and then press QM.
Search type setting: Cable
To start the digital channel search, use the direction buttons  to select YES
and then press OK. To cancel, use the direction buttons  to select NO and
then press QM.
After the end of the automatic channel programming, the channel appears. If the list is not processed further, it closes
after a few minutes.
If the channel list does not close automatically, press the OGPW button to exit the function.
NOTE!
The first time installation described here corresponds to the option FIRST TIME INSTALLATION in
the INSTALL AND RETUNE menu.
First time installation
Welcome please select your language! English
Bienvenue !Veuillez choisir une langue. Français
Willkommen, Wählen Sie bitte Ihre Sprache aus! Deutsch
Benvenuti, Selezionate la vostra luingua! Italiano
Bienvenido, seleccione un idioma Español
Hoş geldiniz, lütfen dil seçimini yapınız! Türkçe
Dobrodošli, izverite vaš jezik! Slovenski
Välkommen, välj ditt språk! Svenska
Üdvözöljük, kérjük válassza ki a nyelvet! Magyar
Bem-vindo, favor selecionar seu idioma Português
Tervetuloa, velitse kielesi! Suomi
Velkommen, velg ditt språk Norsk
Select Language Set Language
OK
First time installation
Country
SearchType
Teletext Language
Scan Encrypted Channels
Welcome!
UK
Digital only
West
Yes
Navigate Continue
Choose your country OK
Please Select Digital Search Type
Aerial Cable
Do you want to start an automatic
channel scan?
Yes No

16
5. Operation
5.1. Channel selection
To select a channel, either press one of the P +/- buttons on the remote control, P/CH +/- on the device or select the
channel directly using the number buttons.
For a two- or three-digit number, press the number buttons in the appropriate order.
Use the (UYCR) button to select the last channel played.
By pressing the QM button on the remote control you can call up the channel list, select the channel with the and
buttons and confirm with QM.
5.2. Sound settings
You can increase or decrease the volume by pressing the volume buttons on the remote control or on the
device.
Use the button to switch the volume fully off and on again.
Pressing the LANG button will display the current audio language.
5.3. Screen settings
Use the RTGUGV to choose between the screen modes: NATURAL, CINEMA, GAME, SPORTS, DYNAM-
IC.
Depending on the programme, the pictures are displayed in the formats 4:3 or 16:9. Use the UK\G button to adjust
the picture format.
AUTO: The format displayed is automatically adjusted to match the input signal.
FULL SCREEN: (only in HDMI mode and for HDTV programmes
received via cable or satellite): Pixel-exact reproduction of the image
(1:1).
16:9: Here you can stretch out the left and right sides of a normal
image (aspect ratio 4:3) by an equal amount to fill the entire width of
the screen.
SUBTITLE: With this function, a widescreen image (aspect ratio
16:9) with subtitles is zoomed to full screen size.
SUBTITLESUBTITLE
14:9: With this function, a wide image (aspect ratio 14:9) is zoomed
to the upper and lower edges of the screen.
14:9 ZOOM: This option sets the 14:9 picture format.
4:3: Is used to view a standard image (aspect ratio 4:3) as this is its
original format.
CINEMA: With this function, a widescreen image (aspect ratio 16:9)
is zoomed to full screen size.

EN
17
You can also change the picture format setting in the menu PICTURE> ADVANCED SETTINGS > PICTURE
ZOOM.
NOTE!
You can move the screen content up or down by pressing the /buttons if the picture format 14:9
ZOOM, CINEMA or SUBTITLE is selected.
NOTE!
Please note that, depending on the video source selected, not all picture formats are available.
5.4. Displaying information
Now: Next:
10:36-11:04The Big Bang Theory
08:476 ProSieben
TXT
;DVB-T S
Q
11:04-11:30 How I MetYour Mother
;;
CH55
5.5. Displaying Information
Press the KPHQ button to show information about the current programme.
You can get the same information when you switch over to a different channel.
PLEASE NOTE!
After pressing OGPW you can open the electronic user manual by pressing KPHQ.
5.6. Opening the favourites list
In the menu CHANNEL LIST > FAVOURITES you can add channels to a favourites list.
Press S the HCX button to activate the favourites list. The favourite icon will be displayed next to the channel name
in the programme information.
Use the R"-1/ buttons to switch between channels in the favourites list.
NOTE!
When you call up the channel list with QM, the favourites list is shown automatically.
Alternatively, use the and buttons to select your favourites and call them up with the QM button.
Press the HCX button again to deactivate the favourites list. The icon in the programme information disappears.
5.7. Selecting the source
NOTE!
Please note that when connecting with the UQWTEG button the source (the connected device) will only be
recognised if it has been activated in the menu SETTINGS, submenu SOURCES.
Use the UQWTEG button to select the source of the connected devices. When the SOURCE menu is open, you can
press the corresponding digit to select the desired source directly.
1. TV TV operation (plays back antenna and cable signals)
2. EXT1 Device on the SCART socket
3. SIDE AV Audio/video input on the side of the device using adapter (AV)
4. HDMI1 HDMI input 1
5. HDMI2 HDMI input 2
6. HDMI3 HDMI input 3
7. YPBPR Device on the YPbPr input using adapter (YUV)
8. VGA/PC Device on the PC input
Use the direction buttons to go to the desired source.
Confirm your selection with QM

18
6. Teletext
Teletext is a free service broadcast by most channels and contains the latest news, weather, TV programmes, share pric-
es, subtitles and other information. Your TV offers many useful functions for using teletext including multipage text,
subpage saving and high-speed navigation.
6.1. Using teletext
Your remote control has special buttons for operating the teletext.
Select a TV channel that broadcasts teletext.
Press button once to display the start/index page.
Pressing again makes the text transparent in front of the TV image.
Pressing a third time switches the device back into TV mode.
6.1.1. Selecting a teletext page
Number buttons
Enter the number of the desired teletext page as a three digit number using the number buttons.
The selected page number is displayed in the top left corner of the screen. The teletext counter searches until it
finds the selected page number.
Scrolling through pages
Using the channel selector buttons or the direction buttons and you can scroll back and forth through the
teletext pages.
Colour buttons
If coloured text entries are displayed at the lower edge of the screen then you can select the contents directly by
pressing the appropriately coloured button RED, GREEN, YELLOW and BLUE.
Subpages
Some teletext pages have subpages. The lower edge of the screen may contain something like 1/3, for example. The
subpages are displayed one after another at an interval of about half a minute. You can call up these subpages by press-
ing the or  button. A four-digit input box appears in which you can enter the number of the subpage (e.g. 0002).
Alternatively you can scroll through the subpages using the direction buttons .
INDEX
Use the TGVWTP button to select the index page, which has a list of the teletext content.

EN
19
7. Connecting devices
7.1. Connecting headphones
Connect headphones to the headphone jack ( ). You can adjust the volume in the menu SOUND, submenu HEAD-
PHONE. To mute the device’s speakers while using headphones, press the button or turn down the volume in the
menu SOUND, submenu VOLUME
WARNING!
The use of headphones at excessive volumes can produce dangerous acoustic
pressure and lead to permanent hearing damage. Before pressing play, set the
volume to the lowest setting. Start playback and increase the volume to a com-
fortable level. Changing the basic settings of the equaliser can also increase the
volume and thus cause permanent damage to your hearing.
WARNING!
Using headphones/earphones to listen to a device at high volumes for an extend-
ed period can damage your hearing.
7.2. Digital amplier via coaxial connection
Via the SPDIF Coax. OUT connection, you have the option of outputting the audio signal of your LCD TV via a digital
amplifier.
To do this, connect a coaxial cable to the SPDIF Coax. OUT connection on the LCD TV and the corresponding input
on the amplifier.
7.3. Connecting a soundbar/surround sound system
If you would like to optimise the sound output by connecting a soundbar or surround sound system, the following con-
nection types are available:
On the SPDIF Coax. OUT connection
If your soundbar/surround sound system has a coaxial SPDIF connector, use a cinch cable (not included) to connect
this to the SPDIF Coax. OUT connection on the LCD TV.
If your soundbar/surround sound system has an optical SPDIF connector, use an adapter (optical to coaxial, not in-
cluded) to connect this to the SPDIF Coax. OUT connection on the LCD TV.
Via the headphone output
Use a 3.5mm jack to 2 x cinch adapter (not included) to connect the headphone output ( ) of the LCD TV with
the sound inputs of the soundbar/surround sound system. In the menu SOUND, submenu HEADPHONE/LI-
NEOUT you should then select the setting LINE-OUT. After this, the volume of the headphone output can no
longer be set via the HEADPHONE option.
Via the SCART connection
Use a SCART to 2 x cinch adapter (not included) to connect the SCART connection of the LCD TV with the sound in-
puts of the soundbar/surround sound system.
7.4. Connecting a DVD/Blu-ray player
There are a number of options for connecting a DVD/Blu-ray player:
With a HDMI cable
If the DVD/ Blu-Ray has an HDMI connection, connect an HDMI cable (not supplied) to one of the HDMI sockets on the
LCD TV. No additional cable is required for sound transmission.