Mefu MF1700-M1 PRO User manual
Laminate Your Value
www.mefuchina.com
Contents
General Information
Panel
Warning Symbols
Safety
Installation and Notice
Operation
Maintenance
Troubleshooting
Repairs
Accessories
Technical Specification
General Information
Warm Laminator(Optional Cutter) MF1700-M1 PRO, 1630mm/64” updated from classic
M1 & M1+, keep the advantages of silicon roller, pneumatic lift etc. With optional cutters,
not only save the cost and time but adjust all positions during lamination, will prevent
any printings or laminating mistakes.
Equipped with more stronger frame ensures more stable and easy to operate, that is this
model can achieve laminating and cutting in one machine with high performance. It has
been the most human and efficiency laminating machine ever. With a laminating and
mounting width up to 1630mm(64''), ensures most application possibilities.
Before first use of the MEFU laminator, you should
carefully read this manual, which contains
important instructions, indications and safety
information. Failure to read the manual may result
in serious injury to operators and damage to
machine.
Machine is heavy! Please be careful, when moving.
2
2
3
3
4
5
6
10
10
11
11
11
Laminate Your Value
www.mefuchina.com
Safety
In order to make a full understanding of the machine, please read this manual
carefully before operation. Take care when operating the machine, especially if more
than one operator is using it.
Power supply
The power supply should meet the requirement of the machine.
Function
The emergency stop function and the mechanical stop function for the machine
should be test in connection with installation, servicing, maintenance etc.
Operation
In order to make a full understanding of the machine, please read this manual
carefully before operation.
Maintenance
Do not use water to clean the machine in case of short circuit, electric shock or rust.
In order not to hurt the rollers, please do not put any hard stuff on the machine.
Check the chains and gears at a regular time, clean and lubricate.
The rollers are mine parts of the machine, damage of the
rollers will affect the yields. Please rise the upper roller up
after lamination, in case of the deformation of the lower
roller under long time weight.
Emergency situations
In the event of an emergency, Press the emergency stop button to stop the laminator in an
emergency. Then the machine will run again and the button will bounce up, when you
clockwise rotate to the neutral position.
Red emergency stop buttons are located at left side of the machine.
4
Laminate Your Value
www.mefuchina.com
Installation and Notice
The MEFU Laminator should be assembled and used in a clean room with a
normal room temperature and normal humidity levels. The work place
should be dry and ventilated. Do not use this machine near water source or
wet ground. This minimize the occurrence of static electricity. In the
meanwhile, do not close to combustible and explosive goods.
Delivery inspection
When the machine is delivered, the following units are included:
·MEFU laminator
·Manual
·Accessories
Connections
Voltage: AC220/240V 50-60HZ
Positioning
The MEFU Laminator should be placed in a dry and ventilated situation.
Electrical connectors may only be connected to
socked to sockets with the correct voltage. All
other operations may only be performed by
authorized staff.
Before use
Check the chains and gears (at a regular time), clean and lubricate.
Using
The roller is hot during working, please do not touch it,in case of scalded or bruised.
After use
Place the roller in the idle position, raised 5 mm above the working table.
Clean the roller at a regular time, do not use water to clean the machine in case of short
circuit, electric shock or rust.
Use 80% alcohol, detergent or eraser to clean the rollers after lamination, which can
lengthen the rollers' life.
1.The temperature of the roller should under 40℃and stop heating.
2.Do not focus on one point.
3.Clean the residuum in time, otherwise it will affect the yields.
Assembly with the steps performed by technician
authorized.
5
Laminate Your Value
www.mefuchina.com
Operation
1. Install the oil-water separator
2.Connect the tube (from air compressor) to the air
inlet of oil-water separator.
4. Switch on the laminator
5. Place the roll of cold film and paper tube to the upper rolls (film roll and release liner roll), place the roll of graphic
and paper tube to the the lower rolls (feeding roll and finish product roll), and measure them straightly with scale on
the rolls.
6
3. Plug in
Laminate Your Value
www.mefuchina.com
12. Put down the roll to keep the feeding graphic steady.
13. Adjust the tension depending on your material.
8
15. Install the cutters
14. Lift down the roller.
16. Press “ON/Set” 3 seconds to turn on and
enter led display system, using “Up” or “Down” to
set proper temp for medias
17. In Forward Mode, press “Run” to lamnate, adjust speed
button accordingly.
In Reverse Mode, press”Stop”(Foot-pedal switch) to laminate.
Laminate Your Value
www.mefuchina.com
Maintenance
Every day
·Make sure that the machine is not held any hard stuff and the roller is not
damaged.
·check the buttons on the machine
Once a week
·clean the machine
Once a month
·Clean and lubricate the chains and gears.
·Check the power supply and the foot switch to prevent leakage.
·If you have an air compressor with laminator, check and clean with its manual.
As necessary
·Check the power supply and clean the roller.
10
Troubleshooting
The roller won’t move up and down
1.Reset the emergency stop button.
2.Reset the controls
(If none of this helps, please contact a
technician)
Control panel dead fault
1. Check power supply or emergency button.
2. If the fuse is burn down, just replace.
The roller can not run
1. Regulate the fraction of the rollers
2. Fix or regulate the chain wheel key on the
motor shaft
3. If Motor or speed controller breakdown, Just
replace the motor or the speed controller.
Snow points
1. Rises up the temperature
2. Clean the surface of graphic
3. If there is some problems with the film,
change the film.
Air bubbles or folds
1. Adjust the pressure of the rollers.
2. Make the printings flat
3. Improve speed or lower temperature.
4. Put the beam weight on printings
Printings go tilt
Regulate the pressure of the rollers.
Folds of films
1. Regulate the film roll's fraction
2. Lower the temperature
Finished products are too curled
Regulate the tension of the film or the reception
roll
Laminate Your Value
www.mefuchina.com
Technical Specification
Repairs
Contact a technician
You should first try contacting a technician through the
dealer where you bought your Laminator.
If this is not possible, contact MEFU Technical Service
Phone: +00 86 15890020566
Accessories
For any necessary accessories you need, you can try to
contact the dealer where you bought your MFEU Laminator.
The equipment may only be used for
its intended purposed as specified in
this manual. For any other use may
result in damage or injury, and is at
the user’s own risk.
11
Model
MF1700-M1 PRO
Max width
1630mm/64”
Speed
Up to 12m/min
Laminating type
Cold ( heat-assist)
Heating method
Infrared
Diameter of upper roller
130mm
Max thickness
23mm/0.9”
Warm up time
5-10min
Recommended temp range
30°C-40°C
Max temp
60°C/140°C
Fixed Volt
AC220V-240V 50HZ-60HZ
Fixed power
1600W
Power consumption
0.5-0.8kw/h
Laser safety
Yes
Foot pedal switch
Yes
Dimensions
2200*805*720mm
GW.
260KG
Table of contents
Other Mefu Laminator manuals
