Mega Accy M1300 User manual

M1300
Bluetooth Headset
User Guide
Power On
Power Off
No pairing
with phone
Low Volume
Noise
phone.
for more than 1 second.
manual for more information.
additional pairing in the next time.
manual.
Your phone should support voice dial
call function. Please see your phone
headset.
to phone, please refer to your phone
follow directions.
Weight
Pairing with phone
Transfer Call
2. When you transfer call from headset
press "OK"button on the phone.
5. Enter "0000" (4 zeros) and
p
ress OK
6. Once pairing is completed
successfull
y,
there will be no need f
o
2. Press and hold volume(+) button for
Answering a Call
Ending a Call
Last Number Redialing
Call Rejection
sound.
When
y
ou have incommin
g
call and
y
ou
hear the rin
g
sound
,
p
ress the call butto
n
Press call button shortly until you hear
command from the phone, and then
3. Perform Bluetooth connection with
4. When M1300 appears in the phone,
the phone.
call button for up to 4 seconds.
To turn off M1300, press and hold the
on the front for about 1-3 seconds .
You must pair your headset with phone
before you make a call.
1. Press the call button for power on.
on steadily.
about 4 seconds until the LED turns
To turn on M1300, press the call button
Charging Bluetooth
Charge M1300 fully, before using it.
1. Insert adaptor into charger jack on
the left side of headset.
2. Insert ada
p
tor into an electrical outle
t
3. M1300 will be fully charged within 2
hours.
Headset Features Start using headset
Average 6 hrs
Average 170 hrs
How to pair
1. When you transfer call from phone to
DESCRIPTIONITEMITEM
Call Time
-20 ~ 60 ‘C
120mAh , 3.7V
Approx.
18.4 x 45.7 x 12.8mm
Approx.
9.2 g (0.33 oz)
Specifications
Bluetooth Version V 1.2
Handsfree Profile
Profile Headset Profile
-Stay within 30 ft from your
-Adjust volume of headset
Standby Time
Upto 10m (30 feet)
Operating Temp.
-Check pin code "0000"
or phone.
Call Distance
Size (W x L x H)
Battery
How to call
-Check pairing order of
DESCRIPTION
-Check wheather headset
is at pairing mode.
When
y
ou receive a call
,
p
ress call butt
o
Troubleshooting
shortly.
Transfer Call/Adj.Volume
headset, press call button of the
Make a Voice Dial Call
phone
shortly.
Press call button until you hear beep
When
y
ou finish a call
,
p
ress call button
Adjust Volume
Press volume (+/-) button.
(+)
Call Button
(-)
LED
Indicator
Charger Jack Receiver
MIC
Volume
Button

<<NOTICE>>
* Section 15.19 Labelling requirements
This device complies with part 15 of the FCC rules
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
* Section 15.21 Information to user
The changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
* IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna
or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF
exposure requirements and void user’s authority to operate the device.
CE0197
FCC ID URMBCM110