Megapix DWC-MF10M28T User manual

Quick Start Guide
DWC-MF10M28T, DWC-MF10M36TIR,
DWC-MF10M8TIR
MEGApix® 720PTM 1MP Camera
Ver. 1.0 / 2015.03
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
1
1
2
3
4
5
Before installing your camera:
1. The mounting surface must bear ve times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover to be damaged.
This may cause a breakdown or re.
Reset to the Factory Default
Press the reset button for 5 seconds to
return the setup to the factory default.
Warning:
Pressing the ‘Reset’ button will result in
the lose of all setting data.
If needed,
make a note for further
installation.
Detach the dome cover from bottom
case
using the wrench provided.
When closing the dome back on the
camera, align the camera’s dome with the
sticker at the bottom of the camera for proper
sealing and protection
.
Product & Accessories
Part Name
Disassemble the Camera
Installation
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that the plug is easily
accessible.
Camera Cables
Screw &
Plastic Anchor-3pcs
Manual CD
Quick Manual
Template Sheet
for installing by Plate
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut Mount Plate Torx Wrench
Plate Hook
Mount Plate
Lens
Reset Button
Bottom Case
Gimbal
Bezel
Tilt Stopper Screw
Reset Button
Template Sheet
DC Power Cable
RJ-45 Cable
Dome Cover
Sticker
20150316
TEL: [phone]
www.Digital-Watchdog.com / [email protected]
Technical Support Hours: Monday-Friday 9:00AM to 8:00PM EST
Detach the camera’s cover dome from the camera’s
module by unscrewing the cover dome screws using the
L-Wrench. See ‘Disassemble the Camera’ for more
information.
Use the camera or mounting template to mark and drill
the necessary holes in the wall or ceiling.
Pull wires through and make connections.
Using three (3) included screws, mount and secure the
camera to the wall or ceiling.
Secure the camera’s cover dome onto the camera base
to complete the installation.
To adjust the camera’s orientation:
1. Loosen the tilt stopper screw at the base of the
camera’s Gimbal by rotating it counter clock-wise.
2. Move the camera to the desired angle.
3. Secure the camera’s lens position by screwing the tilt
stopper screw clock-wise.
To use the LAN water protector case:
1. Insert the network cable into (a), the camera’s
network port.
2. Connect (b) to the camera’s network port by rotating it
clock-wise until tight.
3. Attach part (c) to the case’s body, securing tightly by
rotating it clock-wise.
ab
c

NETWORK
ENVIRONMENTAL
Frame Rate 30 / 25
Video Compression Type H.264, MJPEG
IP IPv4, IPv6
LAN 802.3 Compliance 10/100 LAN
Web Viewer OS: Windows XP / Vista / 7, MAC OS
Browser: Internet Explorer, Chrome, Firefox, Safari
Video Management Software DW Spectrum™
Streaming Capability Multi Streaming CBR/VBR
Power Requirement DC 12V, PoE (IEEE802.3af Class 2)
Power Consumption 1 92W, 160mA / LED ON: 2.7W, 230mA
Operating Temperature/ Humidity -10
o
C ~ 50
o
C (14
o
F ~ 122
o
F), Less than 90% Humidity
Dimensions Ø 125 x 74.3 mm (Ø 4.9 x 2 9 inch)
Material Aluminum Housing
Weight 700 g (1.54 lbs)
Maximum User Access 4 Users
MECHANICAL
ELECTRICAL
Resolution 720p/SVGA/D1/VGA/CIF/QVGA/QCIF
IP Rating IP66 (Protects against dust and high pressure water)
LENS
IMAGE
Image Sensor 1/2 9" 1.0M CMOS
Lens Type Fixed Lens
Focal Length 2.8mm [DWC-MF10M28T]
3.6mm [DWC-MF10M36TIR]
8.0mm [DWC-MF10M8TIR]
IR Distance 30ft Range IR [IR models Only]
20150316
TEL: [phone]
www.Digital-Watchdog.com / [email protected]
Technical Support Hours: Monday-Friday 9:00AM to 8:00PM EST
DW Desktop Tool™
Use the DW Desktop Tool™ included in the camera’s accessory CD to scan the network and detect all MEGApix cameras.
Use the DW Desktop Tool™ to set the camera’s network settings,perform rmware upgrade or access the camera’s web client
1
2
3
4
5
6
To adjust the camera’s orientation:
1. Loosen the tilt stopper screw at the base
of the camera’s gimbal by rotating it
counter clock-wise.
2. Move the camera to the desired angle.
3. Secure the camera’s lens position by
screwing the tilt stopper screw clock-wise.
Template Sheet
Power
Ethernet cable
Ethernet cable
Two Options
Use a PoE-enabled switch to connect data and power through a single cable and begin
viewing and recording images instantly. A non-PoE switch will require an adapter for
power transmission.
1. Using a PoE-Enabled Switch
The Camera is PoE-compliant, allowing
transmission of power and data via a
single Ethernet cable.
PoE eliminates the need for the dierent
cables used to power, record, or control
the camera.
Follow the illustration below to connect
the camera to a PoE-enabled switch
using an Ethernet cable.
2. Using a Non-PoE Switch
If a PoE-enabled switch is not used,
use a power adapter for power
transmission
and non-PoE switch for
data transmission.
Follow the illustrations below to
connect
the camera without a
PoE-enabled Switch.
Cabling Specications
Web Viewer Screen
Installation Using Mount Plate Installation Using Mount Bolt & Nut
Template Sheet
1
3
2
4
5
Detach the camera’s cover dome from the
camera’s module by unscrewing the three
cover dome screws.
Using the metal mount plate, mark and
drill the necessary holes in the wall or
ceiling.
Pull wires through and make connections.
Using the three (3) included screws, mount
and secure the camera to the wall or
ceiling.
Attach the camera base to the metal
mount by snapping it into place using the
two metal handles.
Secure the camera’s cover dome onto the
camera base to complete the installation.
See ‘Disassemble the Camera’ for
water-proof cabling installation.
Detach the camera’s cover dome from the
camera’s module by unscrewing the three
cover dome screws.
Using the camera or mounting template,
mark and drill the necessary holes in the
wall or ceiling.
Secure the two long mounting screws to
the camera’s base.
Pull wires through and make connections.
Mount the camera to the mounting surface
using the 2 mounting nuts.
Secure the camera’s cover dome onto the
camera base to complete the installation.
See ‘Disassemble the Camera’ for
water-proof cabling installation.
1
2
3
4
5
7
6
5
1
2
3
4
Web viewer is optimized with Internet
Explorer10 or higher and Chrome.
Live video display. This is the region
for live video stream from the camera.
Setup Menu. Click to setup the
camera’s Video, Network, Events,
System etc.
When the image is not smooth
due to a slow network connection,
you can setup the buffering time to
make streaming video smoother.
PTZ Control- Virtual control for PTZ cameras.
ALARM Control-
Control sensor inputs and
relay outputs on supported cameras.
Backup- Export or print video and images from
the camera on supported models.
Sound Control- Control audio to and from the
camera on supported cameras.
Stream selection button. Select a
stream from the camera’s 3 available
streams to display it in the viewing area
.
Menu options such as PTZ, audio, sensor
and backup options will be disabled for
cameras that do not support those
functions.