meitav-tec ETN-24-SUPER-SI Series User manual

etn24-super-si-series-europe-rev1.3-letter.doc
rev. 1.3 22/06/2006
On/Off Select Prog
Cool
Heat
Auto
Fan
Setting
Meitav-tec Ltd (Contel group)
Tel: [phone] Fax: [phone]
www.meitavtec.com - [email protected]
ETN-24-SUPER-SI Series
Owner’s Manual – Installation and Operating Instructions
Please read this manual carefully before installation and use.
Index
Options & Accessories 1
Installation Instructions 2
Wiring Connections 3
DIP switch Explanation 4
Operating Manual 5
Remotecontrol 6
Technician Settings 7
1. Options & Accessories
•External sensor option: RS01 for remote temperature sensing (1 required) RS01 for
averaging temperature with thermostat (4 required) RS02 for averaging temperature with
thermostat (2 required RS02 has two thermistors in one enclosure).
•Hand held remote control.
•Door switch or window contact connection.
2. Installation Instructions
Separate the front panel from back panel by depressing the
tongue located in the top of the unit.
Pull the back panel out.
Line the back panel up against the wall or flat surface. Install
three screws as required.
Make electrical connections as shown on enclosed electrical
wiring diagram. (Next page)
Install the cover to the back panel; first the two tabs on the
bottom and then the top tongue. Push until tight against the
wall.

2
1 2 3 4 5 6
3. Wiring Connections
Choose the right configuration for your model.
SWITCH FUNCTION
R 24 Vac RED
C 24 Vac Common from transformer
0 Window contact
T Window contact
S1 HEAT PUMP / HEAT 3 (W3)
S2 HEAT 1 (W1)
S3 HEAT 2 (W2)
S4 External sensor
S5 External sensor
S6 COMP.2 (Y2)
S7 FAN
S8 COMP.1 (Y1)
IMPORTANT! Before making any changes in the DIP switch disconnect electricity in
the main board.
4. DIP switch Explanations (different configurations)
Location of DIP switches:
Factory default configuration for DIP switches:
S2 S1
DIP switches S2 S1
1 2 3 4 5 6

3
1 2 3 4 5 6
Table 4.1 – DIP switch selection
DIP switch S1:
Func. Fan Mode in Econ. Time Delay Cool only or All modes Window Contact
No. Auto Fan* Continuous 4 Minutes* No Delay** Cool only All modes* OFF* Change Set
point “EC”
1 OFF* ON X X X X X X
2 X X X X OFF ON* X X
3 X X OFF* ON X X X X
4 X X X X X X X X
5 X X X X X X X X
6 X X X X X X OFF* ON
X = Not important * = Default switch ** = No delay for compressor – for test only
DIP switch S2:
Func. Internal/External
Sensor Display of T. Ambient HC / HP configuration
HC configuration HP configuration
No. Internal* External
COOL &
HEAT
(HC##)*
HEAT
PUMP
(HP##) With*
display No display Elc.
Heat* Oil Heat HP in
Heat HP in Cool
1 ON* OFF X X X X X X X X
2 OFF* ON X X X X X X X X
3 ON* OFF X X X X X X X X
4 X X OFF* ON X X X X X X
5 X X X X X X OFF* ON OFF ON
6 X X X X ON* OFF X X X X
X = Not important * = Default switch
4.2 DIP switch Operation
The DIP switch has 6 pins.
Each pin can be ON or OFF.
In this example picture, pins 1,6 - ON and pins 2,3,4,5 - OFF
4.3 External sensor connection - option
Important! The external sensor must be Meitav-Tec type.
Table 4.3 - N.TC. Sensor: Temperature ~ Resistance Characteristics
Temp °C 7.2 10.0 12.8 15.6 18.3 21.1 23.9 26.7 29.4 32.2
Temp °F 45 50 55 60 65 70 75 80 85 90
Res. k 115.8 100.9 88.1 77.1 67.7 59.6 52.5 46.4 41.2 36.6
The default from factory is INTERNAL SENSOR.
•Disconnect power to the thermostat 24vac.
•Move the DIP switch S2 as described in the table above
•Connect the temperature sensor to S4, S5 terminals.
•Reconnect power 24vac.
•Make sure the reading in the display is by the external sensor.
The length of the cable for the external sensor is 100 feet (30 meters) with standard cable.
If longer distance is needed then the cable MUST be shielded.
There is a wide range of sensors for different applications, duct, rooms, etc.
There is also option for averaging the temperature.
For details please contact our technical line or visit our web site.
1 2 3 4 5 6
Example
1 2 3 4 5 6
Default:
Default:

4
5. Operating Manual
5.1 On/Off
•Press the ON/OFF button to activate or deactivate the thermostat.
•The word "ON" or "OFF" will appear in the display.
5.2 Set temperature
•Press the SET buttons (+) or (-) - the temperature will flash.
•Adjust the set temperature using the (+) or (-) buttons.
5.3 Selecting modes
Press the MODE button to switch between the four modes:
•Cool
•Heat
•Cool/heat (auto-change over),
•Fan only.
•Emergency heat selectable in heat mode in Heat Pump type (only).
Press and hold the MODE button (5 seconds) to activate Emergency
heat (Heat Elements) and the compressor will be OFF.
This selection is for cold days when the outside temperature is very low and the
Heat Pump is active in heat.
To return back to Heat mode press and hold the MODE button again (only in Heat mode).
5.4 Fan/Auto Fan function
•Press the FAN button to select AUTO FAN.
•Press the FAN button again to cancel.
In AUTO FAN the fan will only run when calling for heat or cool.
6. RT03-HC-1S - Hand Held Remote Control - Option
6.1 General
This is an Infrared Remote Control Unit, which means it must be pointed at the thermostat (or
extra receiver) to operate.
Every time you change a parameter in the Remote Control, you must send it to the thermostat
by pressing the "ON/SEND".
6.2 RT03-HC-1S - Operating Manual
•Press the ON/SEND to activate the air conditioner and/or updating information.
Fan Mode:
•Press the FAN button to change between: FAN ON ( ) or AUTO FAN (A).
•Press the ON/SEND button to send information to thermostat.
Mode:
•Press the MODE button to change between:
COOL, HEAT, AUTO CHANGE and FAN ONLY.
•Press the ON/SEND button to send information to thermostat.
Temperature Set Point:
•Adjust the desired temperature using the (+) or (-) buttons.
•Press ON/SEND button to send information to thermostat.

5
Real Time Clock and Day:
•Press the SELECT button - CLOCK SET will flash.
•Press the (+) or (-) buttons - the hours will flash.
•Adjust the hours using the (+) or (-) buttons.
•Press the SELECT again - minutes will flash.
•Adjust the minutes using the (+) or (-) buttons.
•Press the SELECT again to return to normal display
mode.
•Press the ON/SEND button to send information to the
thermostat.
Timer:
IMPORTANT: If no button is pressed for 10 seconds the display will return to normal
display mode.
Start Time:
•Press the SELECT button twice - PROGRAM & START
(flashing) will appear on display.
•Press the SELECT button - the hours will flash.
•Adjust the hours using the (+) or (-) buttons.
•Press the SELECT button - the minutes will flash.
•Adjust the minutes using the (+) or (-) buttons.
Stop Time:
•Press the SELECT button - PROGRAM & STOP (flashing)
will appear on display.
•Press the SELECT button - the hours will flash.
•Adjust the hours using the (+) or (-) buttons.
•Press the SELECT button - the minutes will flash.
•Adjust the minutes using the (+) or (-) buttons.
•Press the SELECT button - the TIMER will blink
•Select TIMER ON or OFF Using the (+) or (-)
buttons.
•If you changed between TIMER ON or OFF, the
SEND will blink.
•Press SEND/ON button to send the information to
the thermostat.
•If you did not change between TIMER ON or OFF,
press the SELECT button to return to normal display mode.
Important: when the Timer is active, and there is power failure to the thermostat,
the display will show “ON” flashing.

6
7. Technician Settings
7.1 Set temperature limits and offset
•Press and hold ON button (5 second)
•Set the temperature to 55°C.
Set limit for cool
•Press the ON button.
•“COOL” will appear on display.
•Adjust set limit for cool using the (+) and (-) buttons.
Set limit for heat
•Press the ON button again.
•“HEAT” will appear on display.
•Adjust set limit for heat using the (+) and (-) buttons.
Important: The user can change the set temperatures on the display regardless of
the limit set, but the thermostat will work by the limit settings.
Set the offset (the offset is used for calibration of the measured temperature)
•Press the ON button again.
•“OFFS” will appear on display.
•Adjust set offset using the (+) and (-) buttons (range -6°C/+6°C – default 0°C).
Set point for cool in economy mode
•Press the ON button again.
•“AUX” and “COOL” will appear on display.
•Adjust set limit for cool in economy mode using the (+) and (-) buttons.
Set point for heat in economy mode
•Press the ON button again.
•“AUX” and “HEAT” will appear on display.
•Adjust set limit for heat in economy mode using the (+) and (-) buttons.
7.2 Lock/Unlock the thermostat’s buttons
Lock the thermostat’s buttons
•Press and hold ‘ON’ button (5 second).
•Set the temperature to 45°C.
•Press the ON button again.
•Using the (+) button to Set Lock.
Unlock the thermostat’s buttons
•Press and hold ‘ON’ button (5 second).
•Set the temperature to 45°C.
•Press the ON button again.
•Using the (-) button to Cancel Lock.
Important: In Lock button mode, the remote control still can be used to
operate the unit.

7
7.3 Window contact input
The input, normally open to connect door switch or window contact, etc.
The contact is Voltage free (2 terminals), normally open (active when close)
If window contact closes the thermostat have two options:
•Option A: The thermostat will be turned OFF.
•Option B: The thermostat will change the set point (Economy mode)
To change this options in the thermostat please refer to the dip switch
explanation.
When the thermostat is OFF – the window contact is not active.
7.4 Unit display
•When logic “EC” is selected on thermostat, and the window contact is active (close), the
display will show:
•When logic “OFF” is selected on thermostat, and the window contact is active (close),
the display will show:
Rev. 1.3
Cool
Heat ON
Auto Fan
OFF