Memorex DVR H264 User manual

Network (JPEG2000+H.264)
16Channel Network Stand Alone D R
Audio, USB Backup available
The most stable and reliable real stand-alone Digital ideo Multiplex Recorder
User’s Manual er1.0
NETWORK
AUDIO/SEQ

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
1
INSTALLATION & SAFEGUARDS
All the safety and operating instructions should be read before the unit is operated.
Environment Condition for Inst ll tion
- To prevent electric shock or other hazard, do not expose units to rain, moisture, or dust.
- This unit should be located in an area with low humidity and a minimum of dust..
- lace this unit in a well-ventilated place and do not place heat-generating objects on this unit.
- This unit should not be located in an area where it is likely to be subjected to mechanical shocks.
Before You St rt
- Ensure the power switch is in the OFF position prior to starting.
- Do not attempt to service this unit yourself as opening or removing covers may expose you to
dangerous voltage or other hazards.
- Installation should be performed by qualified service personnel only.
- This unit should be operated only from the type of power source indicated on the manufacturer’s
label and with the power supply included with the unit.
Notice
- Be aware thoroughly about the power connection before installation of the unit.
- Before initial configuration or operation you must first set the TIME/DATE, followed by setting
the unit to the FACTORY DEFAULT settings, lastly clearing the HDD. lease follow these steps
in order.
- ull the unit out of record mode prior to cutting power to the unit. Do this by entering the setup
menu, followed by switching the unit off. owering off the unit while writing to the disks can
cause critical malfunctions. (ex: Recording Error, layback Error, System Error)
- When you set the record type, you have to set the Record Configuration and also Schedule
Setup. This unit records as per the Record type & Schedule setup.
- The [REC] button on the front panel is for emergency record using highest image quality.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the
user of this equipment that there are dangerous voltages within the enclosure which may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to presence of
important operating and maintenance(Servicing) instructions in the literature accompanying the
appliance.
Installation & Safeguards

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
2
Contents
Contents
CHA . 1 Features & ackage Contents ---------------------------------------------------------------- 4
1-1. Features ---------------------------------------------------------------- 4
1-2. ackage Contents ---------------------------------------------------------------- 5
CHA . 2 Function of Each Button ---------------------------------------------------------------- 6
2-1. Front ---------------------------------------------------------------- 6
2-2. Rear ---------------------------------------------------------------- 8
CHA . 3 Installation ---------------------------------------------------------------- 9
3-1. Installation Configuration ---------------------------------------------------------------- 9
3-2. Detailed Installation ---------------------------------------------------------------- 10
1) Rack Mount ---------------------------------------------------------------- 10
2) HDD (Hard Disk Drive) ---------------------------------------------------------------- 10
3) Camera ---------------------------------------------------------------- 11
4) Monitor ---------------------------------------------------------------- 11
5) ower ---------------------------------------------------------------- 11
6) S OT, Video rinter ---------------------------------------------------------------- 12
7) Other External Device ---------------------------------------------------------------- 12
CHA . 4 Operation ---------------------------------------------------------------- 13
4-1. System Log-in ---------------------------------------------------------------- 13
4-2. Factory Default ---------------------------------------------------------------- 13
4-3. Display Configuration ---------------------------------------------------------------- 14
4-4. Live View Setup ---------------------------------------------------------------- 14
1) Full / Multiple View ---------------------------------------------------------------- 14
2) View in Sequence ---------------------------------------------------------------- 15
3) I View ---------------------------------------------------------------- 15
4) Freeze View ---------------------------------------------------------------- 15
5) Zoom View ---------------------------------------------------------------- 15
4-5. Record ---------------------------------------------------------------- 16
4-6. layback ---------------------------------------------------------------- 16
4-7. Search ---------------------------------------------------------------- 17
4-8. TZ Camera Operation ---------------------------------------------------------------- 17
4-9. Data Back-Up ---------------------------------------------------------------- 18
4-10. Audio Operation ---------------------------------------------------------------- 19
4-11. Mouse Operation ---------------------------------------------------------------- 19
CHA . 5 Set Up ---------------------------------------------------------------- 22
5-1. Entering the Menu ---------------------------------------------------------------- 22
5-2. Display Setup ---------------------------------------------------------------- 23
1) Screen Display ---------------------------------------------------------------- 23
2) Monitor Setup ---------------------------------------------------------------- 23
5-3. Configuration ---------------------------------------------------------------- 24
1) HDD Management ---------------------------------------------------------------- 24
2) TIME/DATE Setup ---------------------------------------------------------------- 26
3) Camera Setup ---------------------------------------------------------------- 26
4) Interval Setup ---------------------------------------------------------------- 28
5) Alarm Setup ---------------------------------------------------------------- 28

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
3
Contents
6) Event opup Setup ---------------------------------------------------------------- 28
7) Buzzer Setup ---------------------------------------------------------------- 29
8) assword Setup ---------------------------------------------------------------- 29
9) System Information ---------------------------------------------------------------- 29
5-4. Record Setup ---------------------------------------------------------------- 30
1) Record Configuration ---------------------------------------------------------------- 30
2) Schedule Setup ---------------------------------------------------------------- 31
3) Holiday Setup ---------------------------------------------------------------- 31
5-5. Back-Up (CD-R, USB) ---------------------------------------------------------------- 32
5-6. External Device ---------------------------------------------------------------- 33
1) TC /I Setup ---------------------------------------------------------------- 33
2) RS-232C Setup ---------------------------------------------------------------- 36
3) an Tilt Zoom Setup ---------------------------------------------------------------- 36
4) Spot Monitor Setup ---------------------------------------------------------------- 36
5) Audio Setup ---------------------------------------------------------------- 37
6) Audio Volume Setup ---------------------------------------------------------------- 37
7) Remocon Setup ---------------------------------------------------------------- 37
5-7. Factory Default ---------------------------------------------------------------- 38
5-8. Language Setup ---------------------------------------------------------------- 38
CHA . 6 Network Setup ---------------------------------------------------------------- 39
6-1. DVR Network Configuration ---------------------------------------------------------------- 39
CHA . 7 IRS ---------------------------------------------------------------- 43
7-1. IRS SETU ---------------------------------------------------------------- 44
7-2. DVR SETU ---------------------------------------------------------------- 45
7-3. VIEWER ---------------------------------------------------------------- 46
7-4. BACKU ---------------------------------------------------------------- 47
7-5. LAYER ---------------------------------------------------------------- 49
7-6. TRANSMITTER ---------------------------------------------------------------- 52
7-7. CLIENT ---------------------------------------------------------------- 54
7-8. CMS ---------------------------------------------------------------- 56
CHA . 8 DDNS Web Server ---------------------------------------------------------------- 59
8-1. Register DVR to DDNS Server ---------------------------------------------------------------- 59
8-2. DDNS Setup in DVR ---------------------------------------------------------------- 61
8-3. Web Program ---------------------------------------------------------------- 65
CHA . 9 rogrammers Reference ---------------------------------------------------------------- 66
1) Connector in Assignment ---------------------------------------------------------------- 66
2) RS232 ASCII-CODE ---------------------------------------------------------------- 66
CHA .10 Specification ---------------------------------------------------------------- 68
CHA .11 Remocon Key Definition ---------------------------------------------------------------- 69

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
4
CHAP. 1 Features & Package
Contents
Live View
Real time display per camera
Auto Sequence
I ( icture in picture)
Event opup
Digital Zoom
Display Freeze
Simple layback mode
Simple TZ camera control
Record
Variable Record resolution (For higher picture quality or higher recording speed)
Efficient Image Quality setup in 5 steps
Schedule Record / Holiday Record
Event Record (Alarm / Motion)
Emergency Record
Network
View Live and layback images across I network
Copy images across the network
Network Video Server
Pl yb ck
Search & layback by Date/Time, Event and Camera
Outstanding picture quality by J EG 2000 compression algorithm (No mosaic effect)
Suitable for recording not only images but also text
Various steps in Forward layback Speed
Various steps in Backward layback Speed
Easy and convenient search by Jog Shuttle & Remote Controller
D t B ck-Up
Simple Back-Up using built-in CD Recorder (Back-up CD layer included in the package)
Network Back-Up using Remote Viewer program (Remote Viewer included in the package)
Supports bigger capacity of SATA HDD
USB Device Back-Up available
Others
Multi-Language
VGA option board supports both TFT LCD monitor and CRT monitor
Lock the system by assword
JOG / SHUTTLE
AL/NTSC Auto detection
Control the unit by using Remote Controller [Normal, Single, Universal]
Audio recording : IN-4ch, OUT-1ch (mono)
CHAP. 1 Fe tures & P ck ge Contents
1-1. Fe tures

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
5
CHAP. 1 Features & Package Contents
1-2. P ck ge Contents
1. DVR Main Unit 2. Remote Controller
3. ower Cable 4. ower Adapter 5. User’s Manual 6. Software CD
7. Rubber ad 8. HDD absorber 9. Battery for
remote controller
10. Bolts
ackage Contents Description
1. DVR Main Unit STAND-ALONE DIGITAL VIDEO RECORDER
2. Remote Controller DVR control
3. ower Cable AC power supply to adapters for 12 V DC power
4. ower Adapter 12 V DC power supply
5. User’s Manual User’s Manual
6. Software CD Remote Viewer Software & Back up CD player
7. Rubber ad revent DVR from slipping. Attach it to the bottom of main unit
8. HDD absorber Absorbing the mechanical shock of HDD against the case bottom
9. Battery Battery for remote controller
10. Rack mount
bracket / Bolts
Rack mount bracket
For fixing Rack Mount bracket to DVR (6ea)
For fixing DVR with Rack Mount bracket to 19” Rack (4ea)
For fixing Hard Disk Drive into DVR (8ea)
11. Mouse S/2 Mouse
11. Mouse
J .SHUTTLE
MODE
IR
PTZ
MENU
PI P
FRZZOOM
NEXT
SEAR CH
REC PL AYSTOP SE Q
K . L OCK
Q . PL AY
1/ON 2 / OFF 3/OP EN 4/CL OSE
5/ NEAR 6/FAR 7/WI DE 8/TELE
9/SET 1 0/CL EAR 11/G OTO 1 2/AUTO
16/F415/F31 4/F213/ F1
RUN
ACTI V
E
CAMERA SE TUP
USB
HDDF ULL
RECORD
PLAY
ETHER NET
AUDIO/SEQ
NETWORK

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
6
CHAP. 2 Function of Each
Button
2-1 FRONT
CHAP. 2 Function of E ch Button
Name Function
①LED Lamps Shows status of operation
②-1 USB HOST Back-Up by connecting USB Media to USB HOST
②-2 USB Device Firmware upgrade by connecting C with latest firmware to USB port
③IR IR receiver
④Camera
selection
&
TZ camera
control
1. ressing this button will display a full screen image of that camera
2. Control TZ camera (Each button is assigned for each TZ command)
• ON : LIGHT ON • SET : SET RESET
• OFF : LIGHT OFF • CLEAR : CLEAR RESET
• O EN : IRIS O EN • GOTO : GOTO RESET
• CLOSE: IRIS CLOSE • AUTO : AUTO SCAN
• NEAR : FOCUS NEAR • F1 : USER 1
• FAR : FOCUS FAR • F2 : USER 2
• WIDE : ZOOM IN • F3 : USER 3
• TELE : ZOOM OUT • F4 : No Functions
⑤Record /
layback
REC Emergency Record at continuous, 120ips, SU ER FINE size
STO Stop of Emergency Record and return to Schedule Record
from Emergency Record. layback stop.
LAY layback of recorded data on HDD
SEARCH Search recorded data on HDD
⑥SETU MENU Set up for SYSTEM MENU or Use to exit the menu
Press MENU button before powering off the unit.
ENTER Selects each menu option
NEXT Move to next step
▲▼◀▶ Navigate in the menu
+ - Reduce or increase the option value in the menu
AUDIO/SEQ
NETWORK

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
7
CHAP. 2 Function of Each Button
Name Function
⑦LIVE View
Control
TZ On/Off for AN/TILT/ZOOM control mode
ress this button first to control TZ camera connected to
DVR unit via RS-485
ZOOM Zooming an image
FRZ Freezing an image
MODE Switch to split display
MODE button changes screen-division from (to) full screen
to (from) 16-split screen.
I Display in I ( icture in icture) mode
AUDIO / SEQ ress Once, Select audio channel.
ress Longer, Auto camera image sequencing in full screen
mode.
K.LOCK Lock the key function.
To unlock, press longer time (for several seconds) and then
input the password.
Q. lay
(Quick lay)
lay from image recorded 180ips ago in forward direction.
(in case recorded in continuous mode).
⑧Jog Shuttle
Control
J/SHUTTLE ressing Jog Shuttle button (Ready for use Jog/Shuttle)
: In playback mode, pressing J. SHUTTLE button make
images frozen.
RUN LED on : While you operate Jog or Shuttle
ACTIVE LED on : When J. SHUTTLE button is pressed
⑨Jog Shuttle Very easy and convenient search : ress J. Shuttle button, and images in
playback pause, and then Jog and Shuttle makes it very easy and convenient
to search, forward or backward, fast and slow, as user want.
⑩CD Recorder
(DVD Recorder)
Data Back-up and Firmware Upgrade using built-in CD Recorder

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
8
CHA . 2 Function of Each Button
2-2. REAR
Name Function
1 RS 485 Connection with TZ Camera or other external device using RS 485
interface
RELAY Output Relay out terminal
SENSOR Input Sensor input terminal
2 VGA Connection to VGA Monitor (CRT type or TFT LCD monitor)
Just in case you purchased DVR with VGA option board fixed on the main
board of DVR, you can connect VGA Monitor to DVR unit.
3 ETHERNET Connection to ETHERNET device
4 RS-232C Connection to external device as C using RS-232C to control the DVR
5 CAMERA Input Connection with camera
6 LOO Output Camera loop out
7 MONITOR
Output
Connection with Composite Monitor
8 S OT Connection with additional composite monitor
9 DC ower DC 12V 6.67A Adaptor
10 OWER
SWITCH
ower ON/OFF switch for adapters
To avoid accidental deletion of HDD data, please make sure to press
MENU button and enter into setup menu before powering off the unit.
This takes the unit out of record mode for safe shutdown.
11 Audio Input Microphone Input (4ch)
Audio Output Speaker Output (1ch)
12 Mouse A mouse controlling all functions of DVR

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
9
3-1. Inst ll tion Configur tion
CHAP. 3 Installation
CHAP.3 Inst ll tion

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
10
1) R ck mount
1. Remove 4 bolts on each side cap to
install rack mount.
2. Attach rack mount bracket to DVR.
3. Attach DVR with rack mount bracket to 19” rack.
2) HDD
1. Connect Main Board and HDD using SATA DATA cable and HDD power cable.
2. When you use just 1 HDD, install the HDD onto HDD1 location.
3. When you use 2 HDDs, install the first HDD onto HDD1 location and then install the second HDD
onto HDD2 location in order.
4. Stick the HDD absorber (included in package) on the bottom of case and then install the HDD
on top of them by using the bolts (included in package).
5. Screws must be inserted from outside of the case bottom.
CHA . 3 Installation
3-2. Det iled Inst ll tion
Connection of HDD C ble HDD fix
MAIN BOARD
xx
xx
xx
xx
xx
xx
I/O BOARD I/O BOARD
CD-RW
(
MASTER
)
MAIN BOARD
HDD1
(
MASTER
1) HDD2
(
MASTER
2)
HDD1 HDD2

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
11
CHA . 3 Installation
3) C mer
Before you turn on the ower switch, be sure all necessary devices such as ower
adaptor, cameras and Monitor are connected properly to DVR!
Notice
To avoid accidental deletion of HDD data, please make sure to press MENU button
before powering off the unit. This takes the unit out of record mode for safe shutdown.
Connect one DC 12V, 6.67 A Adaptor to the back side of ower Jack for right operation of
2HDDs and CD Recorder.
4) Monitor
Connect cameras to the camera input on rear panel of DVR marked CAMERA IN.
VIDEO A
IN OUT
VIDEO C
IN OUT
VIDEO B
IN OUT
Connect the video output marked MONITOR to Video-In of Main monitor.
5) Power

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
12
CHA . 3 Installation
6) SPOT, VIDEO PRINTER
7) Other Extern l Device
Connection with additional composite monitor
RS-232C : Control DVR through RS-232C port by using C.
RS-485 : Control external device like TZ Camera. ( in No.1 & No.2 at Terminal Block).
RELAY Output : Relay Output. ( in No.3 ~No.5 at Terminal Block)
SENSOR Input : SENSOR Input (Alarm connection) – ( in No.6 ~ No.26 at Terminal Block)
ETHERNET : Connection to LAN, WAN, Internet.
VGA : Connection to a VGA monitor(CRT,TFT LCD) if optional VGA board is fixed
on the main board as shown in the following figure.
Resolution set by manufacturer is 800x600 60 Hz, and user can set resolution
in MONITOR SETU / VGA SETU / VGA RESOLUTION.
Audio Input : Microphone Input (IN1~IN4)
Audio Output : Speaker Output (OUT)

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
13
CHA . 4 Operation
4-1. System Log-In
DVR LOG-IN
ENTER ASSWORD : _ _ _ _ _ _ _ _
IN UT YOUR OWN ASSWORD
TO EXIT, RESS [MENU]
1) To enter into the setup menu, press the [MENU]
button.
2) Enter password with channel number button
from No.1 to No.10 on the front of the DVR unit.
(Maximum of 8 digits are available)
3) After inputting the password, press the [ENTER]
button.
Administrator :
If the password entered matches previously set password, “ LOGIN ADMIN” message appears and
you can enter into SYSTEM SETU .
If the password entered does not match previously set password, the DVR unit goes back to live
display mode.
Factory default password is blank. For log-in, just press [MENU] button and then [ENTER] button.
-Factory default password
ADMIN : (Blank)
MANAGER : ‘ 1 ’
USER 1~USER8 : ‘ 2 ’ ~ ’ 9 ’
※We recommend configuring a unique password as per the procedure in
SYSTEM MENU - CONFIGURATION - ASSWORD SETU .
※For security reasons, be sure to make note of your own password.
CHAP. 4 Oper tion
12345
6 7 8 9 10
4-2. F ctory Def ult
Before first operation, you must check first if all connected camera images are displayed properly,
and then login to the SYSTEM MENU. And you also need to set Time/Date, Factory Default, and
then clear HDD. Even though it is brand new one. it is to make DVMR system and HDD ready for
proper operation. Starting recording without FACTORY DEFAULT setting and HDD clear will cause
malfunction.
1. FACTORY DEFAULT 2. HDD CLEAR
DISPLAY SETUP
CONFIGURATION
REOCRD SETUP
BACK-UP
EXTERNAL DEVICE
FACTORY DEFAULT
LANGUAGE
HDD MANAGEMENT
TIME/DATE SETUP
CAMERA SETUP
INTERVAL SETUP
ALARM SETUP
EVENT POPUP SETUP
BUZZER SETUP
PASSWORD SETUP
SYSTEM IMFORMATION
DISPLAY SETUP
CONFIGURATION
REOCRD SETUP
BACK-UP
EXTERNAL DEVICE
FACTORY DEFAULT
LANGUAGE
Refer to page 34. Refer to page 21.

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
14
4-3. Displ y Configur tion
CHA 4. Operation
1) Full / Multiple View
4-4. Live View Setup
Full screen
Multiple screen changes
Switch to multi-screen display by pressing [MODE]. For full image display, just press the channel button
which you want or continue to press [MODE] button until you see full screen.
When you playback images which recorded in 360X240(360X288) resolution, only 1, 4, 9, 13 & 16 split
screens are available. When you playback images which recorded in 360X120(360X144) resolution,
only 1, 4 & 16 split screens are available.
Status of DVR system
Emergency Record (Red)
Schedule Record (Green)
Record Stop (White)
Stop
Forward layback
Backward layback
ause
1/16~1/2x forward playback
1/16~1/2x backward playback
2~64x forward playback
2~64x backward playback
Current Time & Date
Camera Title
ETHERNET status
Connected
Disconnect
HDD Status
In live mode : Amount of data recorded
In layback mode : Amount of data played
LIVE Display
ALARM Record
MOTION Record
CONTINUOUS Record
icture Quality
BASIC
NORMAL
ENHANCED
FINE
SU ER FINE
120(100) I S @ 720x240(720x288)
240(200) I S @360x240(360x288)
480(400) I S @360x120(360x144)
I
FREEZE
SEQUENCE
ZOOM
AUDIO
360x240
360x120
(
)
¼ Full Screen
<During layback>

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
15
CHA . 4 Operation
3) icture in icture( I View)
When it is in full screen display mode, you can see other camera in a small
window by pressing [ I ].The other camera in small window is rotating in
sequence to next number of camera and you can set the rotating time
interval as per the procedure in SYSTEM MENU-CONFIGURATION-
INTERVAL SETU .
CAM-01
4) Freeze View
Full display mode : If you press the [FRZ] button, the FRZ icon will be activated on the
screen and “F” character will be shown beside camera title, and
live image will be frozen.
Split display mode : If you press the [FRZ] button, the FRZ icon will be activated on the
screen. press the channel button which you want to freeze.
To release frozen image, press channel number of frozen image again
and press [FRZ] button to exit FRZ mode.
5) Zoom View
2) View in Sequence
ress [SEQ] button. It automatically displays full screen images in sequence.
2
In full screen, press the [ZOOM] button and move the Selection Frame using J.SHUTTLE or Direction
keys to the area which you want to enlarge. And then press the [ENTER] button for 2-times enlarged
picture. To exit Zoom mode, just press [ZOOM] button again.
Horizontal Movement : J.SHUTTLE
Vertical Movement : Hold [U or DOWN] button and turn J/SHUTTLE
CH16
……
CH02
CH01
●
●●
●
●
●●
●
●
●●
●

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
16
CHA . 4 Operation
4-5. Record
Recording mode set before delivery by manufacturer (Default recording mode) is Schedule Recording.
In this default recording mode, it records 24 hours/day continuously in weekday and on the weekend.
Once you press the [REC] button while you see live view, the record type is changed to Emergency Record mode.
- Emergency Record : at full resolution/in best quality
Record type : CONTINUOUS, SU ER FINE quality,
120 (100) ips at 720X240 (720x288)
- Schedule Record
Record and stop as set (time interval and
record type) in RECORD-SCHEDULE SETU menu.
- Stop Record
Recording stopped as set in
RECORD-SCHEDULE SETU menu.
On the screen
- Emergency Record
: Red Record Icon ( ) and Record LED is lit
- Schedule Record
: Green Record Icon ( ) and Record LED is lit
- Record Stop
: White Icon ( ) and Record LED is off
- Motion Record, Alarm Record, Alarm + Motion Record
: Record standby LED blinks
: Record LED is lit
※While in Emergency Record mode, press [STO ],
[ LAY], [MENU], or [SEARCH] button to exit from
Emergency Recording mode and return to Schedule
Record mode.
※For details, refer to the SYSTEM MENU – RECORD
SETU ( age 30)
- This DVR unit does not record in following conditions ;
※While entered in the Menu.
※No camera is connected
※Overwriting is off in the Record Setup menu. ( HDD full )
Emergency Record [RED]
Schedule Record [GREEN]
4-6. Pl yb ck
On record mode or stop mode, press [ LAY] button to play the recorded data in 1x speed.
For backward playback, press [ LAY] button again.
Use Jog/Shuttle to pause and control playback speed. To stop playback, press the [STO ] button.
Using Jog/Shuttle
The [ACTIVE] LED will be lit, and Jog/Shuttle is ready for use. The [RUN] LED will blink whenever you
operate the Jog/Shuttle.
For forward playback, turn the Shuttle right and turn Shuttle left for backward playback.
Turn Jog using your index figure to see picture by picture in forward or backward direction.
Operation of Shuttle is as follows.
1/4 x : 4 times slower than normal playback speed
1/2 x : 2 times slower than normal playback speed
1 x : Normal playback speed
2 x : 2 times faster than normal playback speed
4 x : 4 times faster than normal playback speed
16 x : 16 times faster than normal playback speed
64 x : 64 times faster than normal playback speed
Stop Record [WHITE]
If you want to keep the playback speed you selected using Shuttle, just hold the shuttle at that location for a few
seconds, and playback in speed you selected continues until you rotate Shuttle again.
Backward layback 32x supportable.

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
17
CHAP. 4 Operation
4-7. Se rch
ress [SEARCH] button, and 3 different methods for searching recorded data are available as shown
in following SEARCH window. For selecting searching method, use direction key or Jog/Shuttle.
After selecting each search method, press [ENTER] button for playback. exit, press [MENU] button.
SEARCH
SEARCH BAR
TIME/DATE
EVENT LIST
SELECT MENU : ▲▼, & [ENTER]
1) SEARCH BAR
Search by percentage of total recorded data. It starts from image corresponding to set % of data
on the search bar.
2) TIME/DATE
Search by time & date. layback starts from the time & date selected.
3) EVENT LIST
Search by event list (Motion, Alarm, Video Loss).
RECORD SEARCH BAR
[START] 2007/JUN/15 AM11:34:34
[ END ] 2007/JUN/15 M02:50:45
[TARGET DATE/TIME]
020 %
SELECT: JOG, SHUTTLE
SEARCH : [ENTER], EXIT : [MENU]
TIME/DATE
[START] 2007/JUN/20 AM04:04:12
[ END ] 2007/JUN/20 M08:12:23
IN UT TIME/DATE
2005/JUN/07 AM04:04:12
SEARCH : [ENTER], EXIT : [MENU]
SEARCH p ge SEARCH BAR p ge
TIME/DATE p ge EVENT LIST p ge
EVENT LIST
SEARCH : [ENTER] , EXIT : [MENU]
CH EVENT TIME/DATE 001/001
--
--
--
--
--
--
--
----
----
----
----
----
----
----
---- / - -/ --
---- / - -/ --
---- / - -/ --
---- / - -/ --
---- / - -/ --
---- / - -/ --
---- / - -/ --
-- : -- : --
-- : -- : --
-- : -- : --
-- : -- : --
-- : -- : --
-- : -- : --
-- : -- : --
SELECT: ▲▼, AGE:+-
4-8. PAN/TILT/ZOOM C mer Oper tion
ress [ TZ] button first for TZ control mode. Numeric buttons from 1 to 16 and direction buttons are
assigned for each TZ command, and user can control TZ camera connected to DVR unit by
pressing any one of those 20 buttons, one after the other, as needed, and it is just like control by
separate TZ controller.

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
18
Button TZ command Button TZ command
1/ON OWER ON 10/CLEAR RESET CLEAR
2/OFF OWER OFF 11/GOTO RESET GOTO
3/O EN IRIS O EN 12/AUTO AUTO SCAN
4/CLOSE IRIS CLOSE 13/F1 ~ 16/F4 FUNCTION
5/NEAR FOCUS NEAR U BUTTON TILT U
6/FAR FOCUS FAR DOWN BUTTON TILT DOWN
7/WIDE ZOOM IN LEFT BUTTON AN LEFT
8/TELE ZOOM OUT RIGHT BUTTON AN RIGHT
9/SET RESET SET
4-9. D t B ck-Up
Enter into SYSTEM MENU-BACKU -CD-R SETU .
1) Insert empty CD Recorder media into CD Recorder and select the start time & date from which you want
to back up.
※The START & END time / date in HDD sub-menu only shows start and end of recording.
This is not selectable and editable.
※700MB on CD Recorder sub-menu represent size of CD Recorder media inserted.
2) To set start time of back-up and back-up data size, press the [ENTER] button first on [START] or [SIZE]
sub-menu and adjust using [+] or [-] button and move using [LEFT] and [RIGHT] button for next change.
After setting the time & date and back-up data size, press the [ENTER] button again to exit.
※End of back-up time will be calculated automatically as per start time & date and the back-up
data size you set.
※User can select the back-up data size (size of back-up data from start of back-up) on [SIZE] item but
END of back-up time is automatically determined by DVR system.
3) ress [ENTER] button on BURN sub-menu. DVR system starts burning CD.
4) When burning is completed, CD Recorder media will come out automatically. In the next CD back-up,
start
time of CD Recorder shall be the end time of previous CD-back-up, and you can back-up from that for
continuous data back-up. If you need another backup, repeat the above procedure. To stop backup,
press the [MENU] button.
※During burning CD, it’s impossible to cancel burning process.
5) User can verify the back-up CD on C with BACK-U CD LAYER (Included in ackage).
CD- R SETUP
HDD
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 M08:12:23
CD-R
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 M08:12:23
[ SIZE ] 000MB
BACKU
EXIT : [MENU]
CD-R SETUP
HDD
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 M08:12:23
CD-R 700 MB
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 M08:12:23
[ SIZE ] 700 MB - > 700MB
BACKU
CD-RW BURNING : IMAGE DATA.
EXIT : [MENU]
CHA . 4 Operation

Network Stand Alone DVR
Network Stand Alone DVRNetwork Stand Alone DVR
Network Stand Alone DVR
Network (JPEG2000+H.264)
Network (JPEG2000+H.264)Network (JPEG2000+H.264)
Network (JPEG2000+H.264)
19
4-11. Mouse Oper tion
1) Basic Operation
There are 11 keys that work by Mouse.
LEFT, RIGHT, WHEEL button Click once, double Click, Click longer.
And WHEEL U /DOWN.
2) Status that MOUSE ICON is not appreared
- LEFT button double click : The assigned channel is sequencing to FULL Screen →Left button
duble click, it reverts to previous split screen.
If user selects FREEZE, the assigned channel FREEZE.
- RIGHT button double click : The MOUSE ICON will be on.
Depending on the place of Mouse, it shows Width,Length and BOT.
- WHELL button click longer : Delete MOUSE ICON
- LEFT button click longer : In ZOOM mode, holding this button will change the icon.
If User moves the MOUSE, ZOOM area also moves.
3) Working Status in SETU MENU
- LEFT button click once : ENTER
- LEFT button double click : NEXT
- LEFT button click longer : MINUS
- WHEEL button click once : MODE (Schedule Recording, MASK SETU )
- WHEEL button double click : LEFT (For deleting password)
- WHEEL button click longer : None
- WHEEL button upper : LUS
- WHEEL button lower : MINUS
- RIGHT button click once : MENU
- RIGHT button click longer : LUS
Basically by Left button to select Menu, and by Right button to exit Menu.
Move mouse up and down, left arrow moving and indicate selected menu items.
WHEEL : to plus/minus Left button : to press enter
And Left key (Wheel button double click) : password deletes one by one (Login).
CHA . 4 Operation
4-10. Audio Oper tion
ress [AUDIO] button to select audio channel..Ch1, Ch2, Ch3, Ch4 or silence in due sequence.
※Sound of the selected audio channel comes out in Live display.
Recorded sound comes out in layback.