Memphis Shades 2320-0037 User manual

2320-0037 FATS /SLIMS DETACHABLE PLATE ONLY MOUNTING KIT
06-07 DYNA’S FXDI, FXDCI, FXDBI, FXDI35, FXDC, FXDLI
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
Additional tools required that are not included in this kit.
7/16" or 11mm Wrench.
1.Cover gas tank and front fender with towels to avoid
damage during installation.
2. Install the two mounting plates onto the windshield, using
the bottom and third bolt up. Leave the nylon washers off.
The small tab goes to the bottom, big one at the top. Tabs
point out away from the Headlight. (see fig. 1)
3. Slip the windshield mounting plates and windshield onto
the fork clamps, (see figure 2 and 3) and secure the left and
right side locking mechanism.
4. Adjust the height, angle and alignment of the windshield
and tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make sure
the Locking Mechanism is Fully Engaged after installing
the windshield! (see figure 3)
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
Fig. 2Fig. 1
MOUNTING INSTRUCTIONS
MEM8876 01-01-08
First Bolt
Third
Bolt
Read and follow these directions carefully.
During installation, make sure that the windshield and hard-
ware do not interfere with any cables or wiring when the forks
are turned all the way in either direction. Also make sure,
through the full range of adjustment, that the windshield and
hardware do not hit the tank.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.

2320-0037 FATS /SLIMS DETACHABLE PLATE ONLY MOUNTING KIT
06-07 DYNA’S FXDI, FXDCI, FXDBI, FXDI35, FXDC, FXDLI
MOUNTING INSTRUCTIONS
2320-0037 FATS/SLIMS PLATE ONLY KIT
MEM8876 01-01-08
CORRECT
Fully engaged
Locking mechanism
NOT CORRECT
1. Place lower slot into lower bushing. 2. Rotate top slot into
place. 3. & 4. Secure locking Mechanism.
12
3
Figure 3
4
Loosen Allen Bolt to adjust angle, then re-tighten Allen Bolt.
R322C/T
LATCH
ASSEMBLY
1. M1137
2. M1138
21
PART #
M1138
M8876
DESCRIPTION
RIGHT MOUNTING PLATE FATS/SLIMS
MOUNTING INSTRUCTIONS/PARTS LIST
QTY.
1
1
M1137 LEFT MOUNTING PLATE FATS/SLIMS 1
R322 C/T
LATCH ASSEMBLY 2
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
you can also reach us at
[email protected]