Memphis Shades MEK1938 User manual

Additional tools required that are not included in this kit.
7/16" or 11mm Wrench.
1. Cover gas tank and front fender with towels to avoid dam-
age during installation.
2. Install the two mounting plates oponto the fairing using
the black washer and acorn nut supplied with the fairing.
( Fig 1). Tabs point in towards the headlight.
3. On the Roadliner, use the 5mm Allen wrench, locate and
remove the two upper allen head bolts, one on each side of
the headlight. (Fig 2)
4. On the Stratoliner, remove the OEM windshield and
mounting hardware.
continued over….
Part No. 2321-0172
Yamaha Roadliner / Stratoliner 2006- 2010
MS Batwing Fairing
Mounting kit, Black
Detachable system allows easy removal.
Stylish and Functional.
Durable, electropainted finish.
Before assembly, read Warnings inside
MEK1938
WARNING
During installation, make sure that the fairing and
hardware do not interfere with any cables or wiring
when the forks are turned all the way in either direction.
Also make sure , through the full range of adjustment,
that the fairing and hardware do not hit the gas tank.
1.
2.
3.
This is a detachable fairing, ALWAYS make sure the
locking mechanism is fully engaged after installing the
fairing.
The improper installation of this kit and related
components could result in serious injury or death.
CAUTION
Memphis Shades fairings are made from Lucite®
acrylic, and will last for years with proper care. Clean
your fairing with plenty of soapy water (mild dishwash-
ing liquid is best) and a soft cotton cloth. Use your bare
hands to feel and dislodge bugs, or cover with a wet,
soapy towel and let it soak. Don’t use paper towels and
scrape with anything. Small scratches can be removed
with NOVUS #2.
1.
Never use any glass cleaning products, petroleum
based chemicals, or cleaning agents with ammonia,
bleach or any other harsh chemicals. This includes (but
not limited to) RainX, brake fluid, acetone, paint thinner,
benzene and gasoline. “If it hurts your nose, it will hurt
the plastic.”
2.
Glass cleansing agents will cause severe damage to
your fairing, and will void your warranty.
3.
Ref Code Description Qty
nI1938 Mounting Instructions 1
oM1226 Throttle side plate assembly, black 1
pM1225 Clutch side plate assembly, black 1
qM1088 Throttle side bracket assembly 1
rM1087 Clutch side bracket assembly 1
sR319 1/2” diameter spacer 2
tM366 8mm x 30mm Button head cap screw 2
uR320 1 1/2” Support spacer 2
vR312 8mm Flat washer 2
wM1450 8mm x 25mm Button head cap screw 2
R306 5mm Long arm allen wrench 1
M310 3/16 Short arm allen wrench 1
Memphis Shades warrants all product components, metal
and plastic, against defects in materials and workmanship
for 24 months.
For Parts and Warranty Help, Contact:
Memphis Shades, Inc.
P.O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or you
can also reach us by email:
[e-mail]
1. Kit Contents
2. Mounting Instructions
At certain times of the day the Sunlight can reflect off
the curvature of a fairing and cause extreme heat build-
up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an
opaque object over the instruments or adjust the fairing
to avoid reflections.
4.
REVISION 0
nqr
s
t
v
w
p
o
u
11
12
11 12

Part No. 2321-0172
2. Mounting Instructions, continued
Fig. 4
5. Install the Throttle side bracket qby placing the support
washeruinto the upper hole, “the large part faces out, the
small part faces in” followed by the bracket and then
loosely install the 8mm x 25mm button head cap screww
and 8mm Flat washerv. (Fig 2)
6. Locate and remove the two unused bolts in the lower
triple tree, one on each side of the headlight and discard.
Install the lower screw by inserting one of the new 8mm x
30mm button head screwstin this order, through the
bracketq, through the spacer sand tighten the lower and
upper bolt.
7. Repeat step 6 for the Clutch side bracketp. (Fig 2)
8. Install the fairing by placing the lower slots into the lower
mounting bushings. Slip the upper slots into the upper
mounting bushings and gently but firmly seat the slots into
place.
Lock the locking mechanism into place. (Fig 3 and 4)
9. Adjust the height, angle and alignment of the fairing and
tighten ALL bolts.
Note: This is a detachable fairing, ALWAYS make sure
the Locking Mechanism is Fully Engaged after install-
ing the fairing! (Fig 4)
Fig. 1
Fig. 2
Fig. 3
Yamaha Roadliner / Stratoliner 2006- 2010
MS Batwing Fairing
Mounting kit, Black
Step 2Step 1 Step 4 Step 3
1. Place lower slot into lower bushing.
2. Rotate top slot into place.
3. Secure locking Mechanism.
4. Loosen Allen Bolt to adjust angle,
then re-tighten Allen Bolt.
CORRECT
Fully engaged
Locking mechanism
NOT CORRECT
R322C/T
LATCH
ASSEMBLY