ScorpionExo COVERT X User manual

12
EN EN
1
The mask is easily installed and removed because it is guided by
strong neodymium magnets. Its purpose is to shiled the rider from
excessive winds, dust, and small flying objects. It has two mouth
vents which are covered by mesh filters to filter out smaller
particles. NOTE: The mask is for aesthetics and comfort. It does
not provide protection.
Easily Removable Mask
2
The retractable internal sun visor protects the rider from
excessive sunlight, dirt, and small flying objects. It is
optically clear and features a state of the art fog-free
technology, a anti-scratch hardened coating, and UV
protection.
3
SpeedView® Retractable Internal Sun Visor
4
The removable and washable liner features a soft and
supple hypo-allergenic, anti-bacterial material with
advanced moisture wicking properties.
KwikWick® II Liner Fabric
Two intake vents across the front of helmet and
additional mouth vents in the mask force cool air in.
Aero-tuned ventilation
Use the removable mask only for weather protection,
not for impact protection.
Improper use of the mask may cause severe injury or death
by impacts exceeding the helmet's protection capability.
WARNING
Introduction
Function
Fit
Sun Visor
Ventilation Systems
Congratulations for acquiring a premium ScorpionExo®helmet.
This helmet embodies the latest, state-of-the-art design,
engineering and technology available in the market today
and is an excellent investment for your comfort and protection.
Please remember that no helmet can protect you against
all possible or foreseeable impacts even when built with
the latest and best materials and technology.
The following information will help you to enjoy and properly
care for your helmet.
A helmet’s main function is to protect your head from impact
in case of an accident. To accomplish this, a helmets surrounds
your head with a matrix of materials designed to absorb and
cushion impact energy in some accidents. A helmet is also
designed to provide you with comfort while riding at speed
and in various weather conditions. Yet, there is a trade-off:
A helmet decreases hearing sensitivity, peripheral vision and
physical movement to a certain extent while providing
protection and comfort.
It is important for maximum safety that your ScorpionExo®
helmet fit snugly and comfortably on your head with the retention
strap (chinstrap) properly and snugly fastened. With the chinstrap
securely fastened, move the helmet side to side, up and down,
and forward and backward to ensure that there is no excessive
movement of the helmet on your head. Your skin should move
with the helmet.
The sun visor on your Scorpion EXO® helmet provides protection
from weather, small flying objects, and wind. Additional tinted sun
visors are available to protect your eyes from bright sunlight.
The Scorpion EXO® SpeedView® internal sun visor allows you
to instantly lower the shield while riding.
NEVER USE A DARK OR TINTED VISOR IN DARK OR POOR
VISIBILITY RIDING CONDITIONS.
This is not only unsafe, but also illegal in most countries.
NEVER WEAR A VISOR THAT HAS BECOME SCRATCHED OR
WORN OUT, OR RIDE WITH A VISOR THAT IS FOGGED BY
CONDENSATION. THE SUN VISOR IN YOUR HELMET COMES
WITH A SCRATCH-RESISTANT COATING. The sun visors are
coated, which also loses their capacity in about 2 years.
For this reason, we recommend that you change your visor
at least every two years with a new one.
Ventilation systems are designed and engineered to maximize
your comfort in a wide range of temperatures. Familiarize
yourself with the vents on your street helmet. Some vents
have detents allowing partial opening and closing, thereby
controlling intake and exhaust airflow.Your helmet ventilation
systems should be kept clear of any obstructions including
dirt, insects or other items which could interfere with proper
flow of air. The ventilation systems play an important role,
especially during physical exertion or hot-weather riding.
Ventilation helps decrease the possibility of fogging
on the faceshield.
WARNING
1
2
3
4

34
EN EN
Helmet Overview
FRONT VIEW OF THE HELMET
Front
Intake Vents
Speedview®
Sunvisor
Detachable
Front Mask
Quick Release
Buckle
Chinstrap
Always check to make sure the crown liner, neckroll and
cheek pad are installed before using the helmet.
A helmet without the crown liner and/or cheekpad may
increase your risk of serious injury or death.
WARNING
SpeedView®
Retractable Sun Visor
REMOVING SPEEDVIEW® SUN VISOR
Firmly hold the sun visor
with your hand and gently
pull one side out away from
the helmet to release.
Repeat to release the opposite
side. Reverse process for
installation.
To raise the sunvisor,
simply push the SpeedView®
Sunvisor lever up.
To lower the sunvisor,
simply pull the SpeedView®
Sunvisor lever down.
First, push the button
(in red circle) on one side
of the sleeve.
While pushing the button
completely with one hand,
pull out the mask with
the other hand.
Do the same for the other
side of the sleeve.
Removing and Installing
The KwikWick® II Liner
REMOVING THE CROWN LINER
After removing the mask,
you can remove the crown
liner.
Detach 4 snaps in front and
back of the crown liner, then
pull it off from the helmet.
Reverse the process to
install it again.
REMOVING THE NECK ROLL & CHEEK PAD
Pull it off by detaching
6 velcro points around it.
Reverse the process to
install it again.
Removing The Mask

56
EN EN
Push the mask into two holes in front of the sleeve
until you hear “click” sound.
Be sure to hear this “click” sound to secure the mask.
Then pull the mask to outer direction several times
to check whether it is securely assembled to the helmet.
IMPORTANT NOTE:
The Mask is NOT FOR PROTECTION but for comfort use.
Installing The Mask
Cleaning Your Helmet System
FIRMLY AND SECURELY FASTEN YOUR CHINSTRAP.
Check your chinstrap for tightness occasionally as vibration or wind may
loosen it.
Do not simply pull your helmet down onto your head like a hat. Your
ScorpionExo®helmet should be worn as follows: Using both hands grab
the helmet’s bottom rim while holding the chin straps with your thumbs.
Then “roll” the helmet onto your head starting at the forehead. Continue
rolling the helmet on towards the back of the head until it comes to rest
with your head fully in contact with the inner lining and cheek pads.
None of the components of your ScorpionExo®helmet can be damaged
by water. All headliners and sweat-wicking cheek pads are machine
washable. Wash them with a mild detergent in warm water and allow to
air dry. Hand washing is recommended, but machine washing is also
permitted. Use the “delicate” cycle to prevent the agitator
from damaging the sweat-wicking material covering the liner parts,
HOW TO USE CHINSTRAP
While you are wearing your helmet,
grasp the notched arm of the chinstrap
with your right hand, and the locking
mechanism with your left hand. Pull
the nylon tab with your thumb and
forefinger to open the locking brace.
Insert the notched arm into the slot.
Release the nylon tab to lock the arm
in place. Adjust as needed.
Nylon tab
Locking brace
Open slot
Notched arm
Securing and Wearing
Your Helmet we recommend to place the parts in a washing bag. Do not place
lining parts in the dryer: Excess heat may damage the foam and
coverings. The sun visor may be cleaned with plastic polish or
mild soap and water. The shell of your helmet should be cleaned
using only a mild detergent and water.
Warning
DO NOT
Warranty
For your safety, it is important that you completely read the
owner’s manual and all warning labels.
DO NOT ride without snugly fastening your chinstrap.
DO NOT clean your helmet with petroleum products, solvents,
benzene, thinner or cleaning agents.
DO NOT paint over your helmet’s finish without totally protecting
and isolating the shock-absorbing liner and plastic parts.
Your warranty will otherwise be invalidated.
DO NOT drop your helmet from any height onto a hard surface.
This could cause damage to your helmet’s finished and/or
decrease its ability to protect you.
DO NOT place your helmet on your motorcycle’s rearview mirror:
The sharp pressure from the mirror’s edge will compress and
damage the helmet’s shock-absorbing liner.
DO NOT place your helmet on the motorcycle’s seat or fuel tank.
It can easily roll off and hit the ground causing damage to
the helmet. It is best to place your helmet on the ground so it
cannot fall in any direction.
DO NOT ride with a scratched faceshield. This can impair your
vision, especially at night.
DO NOT modify any part of your helmet, e.g., drilling the shell or
cutting and pressing the shock absorbing liner. Installation of sound
systems, speakers and microphones reduces your helmet’s ability to
protect you and is not recommended.
DO NOT use the helmet again if it has either been dropped or
involved in an accident. Replace it even if the damage is not visible
to the naked eye.
DO NOT wear a dark or tinted faceshield (including the retractable
SpeedViewTM Sunvisor) in dark or poor visibility riding conditions.
DO NOT place your headliners and cheek pads in the dryer after
washing. Allow them to air dry.
DO NOT attempt to remove, change or replace your faceshield while
riding your motorcycle or ATV.
DO NOT use paint which requires heat curing.
All ScorpionExo™ helmets have a warranty of 5 years.
Although there is no visible damage on your helmet, general wear
and tear over time may affect overall function of protective helmet
and increase the risk of injury in accident. It is advisable to replace
your helmet no later than every 5 years from purchase.
Should you have a warranty claim, go to your Scorpion dealer with
your invoice (this is you purchase proof, it's necessary in order to
start the warranty process). You can find our dealers' list on your
website: http://www.scorpionsports.eu/english/dealers/find-a-dealer/
find-a-dealer.html (choose your country and then the
location) The dealer will contact our after sales service
and start the warranty process in order to check
and/or repair your helmet.
WARNING
Small neodymium magnets are used for
easier operation.
The magnet force is not very strong, and generally
each magnet size is not considered as dangerous.
However, consult your physician before using if you are a
pacemaker wearer and not sure about the effect caused
by these magnets.