Memphis Shades 2320-0138 User manual

Part No. 2320-0138
Trigger Lock Mounting Kit
Bullet Fairing
FXSB Breakout
Before assembly, read Warnings inside
MEK1998
WARNING
During installation, make sure that the fairing and
hardware do not interfere with any cables or wiring
when the forks are turned all the way in either direction.
Also make sure , through the full range of adjustment,
that the fairing and hardware do not hit the gas tank.
1.
2.
3.
This is a detachable fairing, ALWAYS make sure the
locking mechanism is fully engaged after installing the
fairing.
The improper installation of this kit and related
components could result in serious injury or death.
CAUTION
Memphis Shades fairings are made from Lucite
acrylic, and will last for years with proper care. Clean
your fairing with plenty of soapy water (mild dishwash-
ing liquid is best) and a soft cotton cloth. Use your bare
hands to feel and dislodge bugs, or cover with a wet,
soapy towel and let it soak. Don’t use paper towels and
scrape with anything. Small scratches can be removed
with NOVUS #2.
1.
Never use any glass cleaning products, petroleum
based chemicals, or cleaning agents with ammonia,
bleach or any other harsh chemicals. This includes (but
not limited to) RainX, brake fluid, acetone, paint thinner,
benzene and gasoline. “If it hurts your nose, it will hurt
the plastic.”
2.
Glass cleansing agents will cause severe damage to
your fairing, and will void your warranty.
For care and cleaning we recommend using Memphis
Shades All Kleer, a unique cleaner/polish, bug
remover and rain repellent that leaves a super slick
surface that makes the next cleaning even easier.
3.
Ref Code Description Qty
I1998 Mounting Instructions 1
M1449EC Throttle side plate assembly 1
M1448EC Clutch side plate assembly 1
S1167 Medium detachable clamp assembly 4
M310 Short arm allen wrench, 3/16 1
1. Kit Contents
2. Mounting Instructions
At certain times of the day the Sunlight can reflect off
the curvature of a fairing and cause extreme heat build-
up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an
opaque object over the instruments or adjust the fairing
to avoid reflections.
4.
Additional tools required that are not included in this kit.
7/16" or 11mm Wrench.
1.Cover gas tank and front fender with towels to avoid
damage during installation.
2.Install the Mounting plate assemblies andonto the
fairing, using the bolts that are pre-assembled on the
Mounting plate assemblies.
The Santoprene grommets should be inserted through the
holes in the fairing so that the flat round part of the grommet
lies flat on each side of the plastic. Tabs point in towards the
headlight. (Fig. 1)
continued overleaf…….
REVISION 0

Aluminum parts are electrocoated (E-coated)
for durability and weather resistance.



WARNING
If the adjustable clamps are installed backwards, it will
result in serious gas tank damage. Always check for
proper gas tank clearance before tightening hardware.
Memphis Shades warrants all product components, metal
and plastic, against defects in materials and workmanship
for 24 months.
For Parts and Warranty Help, Contact:
Memphis Shades, Inc.
P.O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or you
can also reach us by email:
[e-mail]


Part No. 2320-0138
2. Mounting Instructions, continued
Fig. 3
3. Loosely install the four Fork Clamps on the forks, ap-
proximately 2" apart. (Fig 2).
4. Start with Fork Clamp Bushing adjusted to rear of slot
(Fig 3) Then adjust as needed and check for clearance.
(See warning above.)
5. Slip the mounting plates and fairing onto the fork clamps,
(see figure 4) and secure the left and right side locking
mechanism
6. Adjust the height, angle and alignment of the windshield
and tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make
sure the Locking Mechanism is Fully Engaged after
installing the windshield! (see figure 5)
Fig. 4
Fig. 2
Trigger Lock Mounting Kit
Bullet Fairing
FXSB Breakout
Fig. 1
Tabs face in
towards headlight.
WARNING:
"Mounting clamps
backwards will cause
damage to your tank."
Side view. When installed correctly,
Allen bolts are tightened from the
back side of the fork, not the front.
CORRECT
Throttle side,
front of bike
INCORRECT
Throttle side,
front of bike
Loosen Allen Screw to
adjust Bushings to desired
windshield angle.
Rear of slot
1. Place lower slot into lower bushing.
2. Rotate top slot into place.
3. Secure locking Mechanism.
4. Loosen Allen Bolt to adjust angle,
then re-tighten Allen Bolt.
1 2 3 4
CORRECT
Fully engaged
Locking mechanism
NOT CORRECT
R322C/T
LATCH
ASSEMBLY
#memphisshades