Memphis Shades 2321-0226 User manual

Part No. 2321-0226
Trigger Lock Mounting Kit
MS Fats / Slim
Black
Before assembly, read Warnings inside
MEB8980
WARNING
During installation, make sure that the windshield and
hardware do not interfere with any cables or wiring
when the forks are turned all the way in either direction.
Also make sure , through the full range of adjustment,
that the windshield and hardware do not hit the gas
tank.
1.
2.
3.
This is a detachable windshield, ALWAYS make sure
the locking mechanism is fully engaged after installing
the windshield.
The improper installation of this kit and related
components could result in serious injury or death.
CAUTION
Memphis Shades windshields are made from Lucite®
acrylic, and will last for years with proper care. Clean
your windshield with plenty of soapy water (mild dish-
washing liquid is best) and a soft cotton cloth. Use your
bare hands to feel and dislodge bugs, or cover with a
wet, soapy towel and let it soak. Don’t use paper towels
and scrape with anything. Small scratches can be re-
moved with NOVUS #2.
1.
Never use any glass cleaning products, petroleum
based chemicals, or cleaning agents with ammonia,
bleach or any other harsh chemicals. This includes (but
not limited to) RainX, brake fluid, acetone, paint thinner,
benzene and gasoline. “If it hurts your nose, it will hurt
the plastic.”
2.
Glass cleansing agents will cause severe damage to
your windshield, and will void your warranty.
For care and cleaning we recommend using Memphis
Shades All Kleer, a unique cleaner/polish, bug
remover and rain repellant that leaves a super slick
surface that makes the next cleaning even easier.
3.
Memphis Shades warrants all product components, metal
and plastic, against defects in materials and workmanship
for 24 months.
For Parts and Warranty Help, Contact:
Memphis Shades, Inc.
P.O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or you
can also reach us by email:
[e-mail]
2. Mounting Instructions
At certain times of the day the Sunlight can reflect off
the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument
panel. Take care when parking. Park facing the sun,
place an opaque object over the instruments or adjust
the windshield to avoid reflections.
4.
Additional tools required that are not included in this kit.
7/16" or 11mm Wrench.
1.Cover gas tank and front fender with towels to avoid
damage during installation.
2. Install the two mounting plates onto the windshield, using the
bottom and third bolt up. Leave the nylon washers off. The small
tab goes to the bottom, big one at the top. Tabs point in towards
the headlight. (Fig 1)
3.There is an upper clamp and a lower clamp for each fork,(Fig 2a).
The lower clamp has protective film on the inside and does not
have the slotted bushing adjustment. The upper clamp has a flexi-
ble tapered Santoprene insert and does have the slotted bushing
adjustment.
4. On the clutch side, install the lower clamp around the fork tin with
the clamp in the largest setting as shown in Fig 2a. With the
grooves in the polymer bushing facing directly forward, slide the
clamp down until it rests on the lower triple tree and snug it in place
Next, separate the tapered insert from the upper clamp and flex the
insert around the upper part of the fork tin with the raised “stopper”
portion up. Rotate the insert rearward until the raised “stopper” por-
tion is underneath the upper triple tree, with the trailing edge of the
“stopper” portion even with the edge of the upper triple tree.
Continued overleaf…….
REVISION 0
n
Aluminum parts are electrocoated (E-coated)
for durability and weather resistance.
q
p
o
BUSHING
ASSEMBLY
r
s
1. Kit Contents
Ref Code Description Qty
nI8980B Mounting Instructions 1
oM1184EB Clutch side mounting plate assembly 1
pM1185EB Throttle side mounting plate assembly 1
qS1171EC Clutch side, upper fork clamp assembly 1
rS1172EC Throttle side, upper fork clamp assembly 1
sS1173EC Lower fork clamp assembly 2
Fork Clamp
Insert

Part No. 2321-0226
2. Mounting Instructions, continued
Fig. 3
Around the fork tin, slide the two parts of the upper clamp to-
gether in the smallest setting, and slip the clamp over the Santo-
prene insert, and align it with the lower clamp as shown in figure
2b.(The cable guide may need to be bent slightly.)
Repeat Step 4. on the throttle side.
5. Slip the windshield mounting plates and windshield onto the
fork clamps, (Fig 3 and 4) and secure the left and right side lock-
ing mechanism.
6. Adjust the height, angle and alignment of the windshield and
tighten
ALL bolts.
Note: This is a detachable windshield, ALWAYS make sure
the Locking Mechanism is Fully Engaged after installing the
windshield!
Fig. 1
1. Place lower slot into lower bushing.
2. Rotate top slot into place.
3. Secure locking Mechanism.
4. Loosen Allen Bolt to adjust angle,
then re-tighten Allen Bolt.
1 2 3 4
Fig. 4
Fig. 2a
Fig. 2b
CORRECT
Fully engaged
Locking mechanism
NOT CORRECT
R322C/T
LATCH
ASSEMBLY
Trigger Lock Mounting Kit
MS Fats / Slim
Black
First
Bolt
Third
Bolt
Adjustable upper
clamp with tapered
insert
Fixed lower clamp
Warning
Mounting clamps
backwards will cause
damage to you tank
Flex the tapered fork
clamp insert around
the upper fork tin, lip
facing down. Rotate
rearward until the
stopper portion is just
underneath the upper
triple tree
Stopper
Lip
Fig. 2